EverFocus EPH5212 - Manual

6 Issue: 1.0 * The HDcctv Alliance states Look for the unique HDcctv logo to be sure: 100m transmission over even low-grade RG59 Plug-and-play interoperability with other compliant products Forward compatibility with future versions of the standard See www.hidefcctv.org for details 1.3 System Config...

7 Issue: 1.0 2. Installation and Connection 2.1 Package Contents

8 Issue: 1.0 2.2 Base Installation - Make holes for mounting and cable hole on the wall where the dome camera is to be installed. Attach the arm firmly with the supplied mounting screws (4) or other means which will secure the unit properly to resist wind and snow/ice loading. - After mounting the a...

9 Issue: 1.0 2.3 Connection Interface and Wiring cables *Caution Do not connect the power cable until all other connections have been completed. Be sure to remove the shipping foam ring and sheet before connecting the power to the dome camera. 2.3.1 Connecting the RS-485 lines The dome camera can be...

11 Issue: 1.0 3. Programming PTZ and Camera Functions and Options [OSD Menu Structure] - Main Menu/Title - Operation Menu SW302 SW301 SW303 J302

14 Issue: 1.0 3.1 Getting Started You should install and connect the dome to an interface device before using this operating guide. Refer to {2. Installation and connection of this manual}. Once installed, apply power to the dome and the start-up screen is displayed on the monitor. Before installing...

15 Issue: 1.0 The title edit menu can be used in the setup for Preset/Pattern/Tour/Scan commonly. - Move the joystick right in Main Menu. The screen appears on the monitor: - Move the joystick right, left, up or down to select a character. - Press [Tele] button to input a character and [W ide] butto...

17 Issue: 1.0 Use this function to initialize all or specific parameters of dome to factory default parameters. - Enter into {Main Menu} - Select {System} using joystick [ ▶ ] and move to {Initialize} in the sub menu of {System} - Select items to be initialized. - Press [Near] button or use joystick...

20 Issue: 1.0 3.4.4 Image Setup This menu is for changing displayed image settings. - Enter into {Main Menu} - Select {Display} and move to {Image Setup} using joystick [ ▶ ]. - Using joystick [ ▶ ], Normal image, Horizontal image, Vertical image or H/V image can be selected. - Press [Open] button o...

23 Issue: 1.0 increasing the brightness of the overall screen so that subjects being shot with a loss of dark detail due to backlight will have just the right brightness level. - Enter into {Main Manu} - Select {Camera Setup} and move to {AE Setup} using joystick [ ▶ ]. - Set AE mode for Full Auto, ...

24 Issue: 1.0 Sharpness enhances picture detail by increasing the aperture gain of the camera and sharpening the edges in the picture. Digital Image Stabilizer (DIS) function internally detects shaking of the image due to camera shaking and performs digital compensation processing inside the DSP to ...

30 Issue: 1.0 ▲ / ▼ : move joystick up and down for selecting an item. ◀ / ▶ : move joystick left and right for moving an item. ▶ / [Open]/ [Near]: move joystick right to select or save settings or go to edit pages. ▶ / [Close]/ [Far]: move joystick to cancel or to exit current menu (Back). The dome...

33 Issue: 1.0 4. Troubleshooting Guide If problems occur, check the installation of the dome with the instructions in this manual. And refer to this manual for further information. Problem Solution No video on the screen - Verify that power is connected to all components in the system. - - Verify th...

34 Issue: 1.0 5. Specifications 5.1 General Specifications Pickup Device 1/2.8” Sony Exmor R 2.1 megapixel Color Progressive CMOS sensor Pixels 1920x1080 with 2.5µx 2.5µ pixel size Image Area Dimensions 4.8mm x 2.7mm (16:9 aspect ratio; 5.52mm diagonal) Sensitivity 0.2lux/F=1.6 DSS off color; 0.1lux...