Page 2 - ADDENDUM; REVISION SHEET; Revision
ADDENDUM REVISION SHEET Revision Issued Date Revision Page Rev.-A April 28, 1993 1st issue
Page 3 - Stylus-800/1000 SERVICE MANUAL General Description; General Description; Fast; Table 1-1 Print Speed and Printable Column
ADDENDUM Stylus-800/1000 SERVICE MANUAL General Description 1.1 General Description This addendum only summa the major features and specifications which specifically applicable to the 1.1.1 Features ■ Fast printing speed. You can print up to 150 in 10 LQ mode and up to 250 in 10 DRAFT mode. ■ Built-...
Page 4 - General Description; Paper Handling Specification; maximum
ADDENDUM General Description Stylus-800/1000 SERVICE MANUAL 1.1.2.2 Paper Handling Specification Paper Feeding : ■ Friction (either from built-in auto sheet feeder or manual insertion slot) ■ push tractor feed (from rear tractor unit (optional)) Note) Set the release lever to correct position to sel...
Page 5 - paper thickness, as shown in table below.; R I G H T
ADDENDUM Stylus-800/1000 SERVICE MANUAL General Description Adjust lever : The adjust lever, attached to the carriage unit, must be set to proper position for the paper thickness, as shown in table below. Table 1-2 Adjust Lever Position Lever Paper Position LEFT Cut Sheet (Horizontal) Continuous for...
Page 6 - Printer Operations; Panel; type push; INK OUT; Figure
ADDENDUM General Description SERVICE MANUAL 1.1.3 Printer Operations This section describes the basic operation of the printer. 1.1.3.1 Control Panel The control panel of the Stylus-1000 contains six non-lock type push buttons and nine LED indicators for easy controls over the various printer’s func...
Page 7 - SERVICE MANUAL; Table 1-3 Default Setting Item; us
ADDENDUM SERVICE MANUAL General Description 1.1.3.2 Default Setting Item The default setting items of the Stylus-1000 are as listed in table below. Table 1-3 Default Setting Item Menu Contents Description Factory Setting Character Table Select the character table us Italic Auto Print Direction ON: P...
Page 8 - PAUSE; to
ADDENDUM General Description SERVICE MANUAL Error Conditions The Stylus-1000 detects various errors and indicates them with the LED indicators and buzzer as shown in table below. T 1-4 ror Indication Buzzer Recovery Error PAPER INK OUT LED LED O N OFF PAUSE LED ■ x 3 times Set the paper and press th...
Page 9 - Operating Principles; MAIN BOARD Block Diagram
ADDENDUM Stylus-800/1000 SERVICE MANUAL Operating Principles 2.1 Operating Principles The main control circuit of the Stylus-1000 is different from the and is the MAIN BOARD. This board has an additional to which the I/F card The figure below shows a block diagram of the main control circuit board. ...
Page 10 - In addition to the sensors built in the C106 MAIN; HP; CPU; Printhead; Figure 2-2 Sensor Circuit Block Diagram
ADDENDUM Operating Principles Stylus-800/1000 SERVICE MANUAL 2.1.1 Sensor Circuit In addition to the sensors built in the C106 MAIN for MAIN BOARD for the Stylus-1000 is equipped with a sensor which detect the position of the release lever. The release lever is usedto switch between normal paper fee...
Page 11 - Stylus-800/1000 SERVICE MANUAL Disassembly and Assembly; Disassembly and Assembly; specifically applicable to the; assembly
ADDENDUM Stylus-800/1000 SERVICE MANUAL Disassembly and Assembly 3.1 Disassembly and Assembly This addendum only explains the disassembly and assembly procedures specifically applicable to the 3.1.1 Printer Mechanism M-4860 Removal [Step 1][Step 2] [Step 3] [step 4] [Step 5] [Step 6] [Step 71 [Step ...
Page 12 - Disassembly and Assembly; Paper Feed; Motor Removal; Take out the paper feed motor.; Paper Feed Motor; Figure 3-2 Paper Feed Motor Removal
ADDENDUM Disassembly and Assembly Stylus-800/1000 SERVICE MANUAL 3.1.2 Paper Feed Motor Removal [Step 1] Remove the printer mechanism. (Refer to 3.1.1.) [Step Remove two screws ((CBS M3x1O)X2) which fixing the paper feed motor. [Step 3] Turn the paper feed motor for about 90 degree, as shown in figu...
Page 13 - Feed; Roller Assembly Removal; Remove four screws; II; -3 Paper Feed Roller Assembly Removal
ADDENDUM Stylus-800/1000 SERVICE MANUAL Disassembly and Assembly 3.1.3 Paper Feed Roller Assembly Removal [Step 1] Remove the printer mechanism. (Refer to 3.1.1.) [Step 2] Remove the carriage assembly. (Refer to [Step 3] Remove four screws M3x1O)X4, two each at left and right side) and remove the re...
Page 14 - Certain thick and stiff; between; YES; Cw; Figure 4-1 Adjust Tool Set Position
ADDENDUM Stylus-800/1000 SERVICE MANUAL Adjustment 4.1 Adjustment This addendum only explains the adjustment procedures which specifically applicable to the Stylus-1000. 4.1.1 Paper Gap Adjustment [Step 1] Insert the plastic into a paper path from the rear of the printer, at the position shown in fi...
Page 15 - Adjustment; Carriage guide; Figure 3-2 Paper Gap Adjustment
ADDENDUM Adjustment Stylus-800/1000 SERVICE MANUAL Carriage guide Printhead shaft holder / ’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Carriage guide shaft holder stylus 600 o\ ‘ Front frame PG Adjust gag...
Page 16 - SERVICE MANUAL Maintenance; Table 6-1 Recommended Lubricant; Type Name QTY Part No. Availability; Oil; Grease; Ref. No. Lubrication Point Lubricant stylus stylus
ADDENDUM Stylus-800/1000 SERVICE MANUAL Maintenance 6.1 Maintenance This addendum only explains the maintenance which specifically applicable to the Stylus-1000. 6.1.1 Lubrication A proper lubricant must be applied only to the specified points of the printer mechanism for optimal performance. Table ...
Page 17 - Maintenance
ADDENDUM Maintenance Stylus-800/1000 SERVICE MANUAL y’& - . Figure 6-1. Lubrication Points 6 - 2 I
Page 18 - SERVICE MANUAL APPENDIX; Appendix; Connector Summary; Figure below shows the; cl; Printer Mechanism; Figure A-1 Interconnection of Major Components
ADDENDUM SERVICE MANUAL APPENDIX Appendix This addendum only explains the comectors which specifically applicable to the Stylus-1000. Connector Summary Figure below shows the between the major components of the Stylus-1000. AC Input z cl 06 Printer Mechanism (M-4810/4860) I . . . . . . . . . . . . ....
Page 19 - APPENDIX
ADDENDUM APPENDIX Stylus-800/1000 SERVICE MANUAL Board Cl 06/114 MAIN Table A-1 Connector Location Pin 36 pins 1212 465 4 18 Description Centronics parallel l/FHEAD-1 (to HEAD-2 (to sensor PF motor CR motor PS line (from Panel control line (to AC input (UN) DC output (to C106/114 MAIN) (to C106/114 ...
Page 20 - A.3 CIRCUIT BOARD COMPONENT LAYOUT; Control; Board Component Layout
ADDENDUM APPENDIX Stylus-800/1000 SERVICE MANUAL A.3 CIRCUIT BOARD COMPONENT LAYOUT I II 1I 4 I I , 1111! , - 1 . - ” . . . , . .— 12 - - - - - i “ o 0 0 0 0 Figure A-2. Cl 14 MAIN Control Board Component Layout A - 4 REV.-A I
Page 21 - EPSON