Page 2 - Introduction; IMPORTANT SAFEGUARDS; WARNING; Wash hands after handling.
82 Introduction IMPORTANT SAFEGUARDS Read Instructions - All the safety and operating instructions should be read before the appliance is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the product a...
Page 4 - Lithium-ion Battery Handling Precautions; Danger
Introduction (Continued) 84 Lithium-ion Battery Handling Precautions Danger Do not disassemble or modify the battery pack. The battery pack is equipped with built-in safety protection features. Should these features be disabled, the battery pack can leak acid, overheat, emit smoke, burst and/or ig...
Page 5 - Warning
Introduction (Continued) 85 Do not use an apparently damaged or deformed battery pack by drop of the battery pack or any other damage. Otherwise, acid leakage, overheating, smoke emission, bursting and/or ignition of the battery pack may occur. Do not directly solder the battery pack. Otherwise,...
Page 6 - Caution
Introduction (Continued) 86 Caution Do not use or subject the battery pack to intense sunlight or hot temperatures such as in a car in hot weather. Otherwise, acid leakage, overheating and/or smoke emission can occur. Also, its guaranteed performance will be lose and/or its service life will be sh...
Page 7 - BEFORE YOU USE; Temperature of the main body; Clean this
Introduction (Continued) 87 BEFORE YOU USE Temperature of the main body When this recorder is used for a long time in the power-on state, the temperature of the main body may become high. However, this is not a fault. The power plug cord applicable to the local power specifications is attached. Be...
Page 12 - DISCLAIMERS; SD memory card
Introduction (Continued) 92 DISCLAIMERS ● The contents of this instruction manual are subject to change without notice. ● It is prohibited to copy any part or the whole of this instruction manual without our prior written consent. Unless used for personal use, it is also prohibited under copyright l...
Page 14 - Contents
Introduction (Continued) 94 Contents Introduction ...................................................................................... 82 IMPORTANT SAFEGUARDS ....................................................... 82 Lithium-ion Battery Handling Precautions .................................... 84...
Page 15 - Confirming the Accessories upon Unpacking
Introduction (Continued) 95 Confirming the Accessories upon Unpacking AV cable Recorder Camera head Instruction manual AC adapter/ Power cord Battery pack USB cable Earphone Belt clip
Page 16 - Preparations; The Name of Each Part; Recorder
96 Front glass Camera unit Head connector Direction indicator ring ※ The side marked with the ELMO logo indicates the upper side. Screw lock Lens cover Camera cable Preparations The Name of Each Part Recorder Camera Head SD card slot Battery lock USB terminal DC-IN terminal Belt clip RESET Belt clip...
Page 17 - The Name of Each Screen; Warning message display; Playlist; ENTER; SELECT
Preparations (Continued) 97 The Name of Each Screen z Warning message display Message Meaning Load the SD memory card. The SD memory card has not been loaded or may not have been loaded properly. ( Î P104) The SD memory card is locked. Check and load the SD memory card again. The write switch of the...
Page 18 - How to Charge the Recorder
Preparations (Continued) 98 How to Charge the Recorder 1 Set in the battery. Fit the catches of the battery in their mating slits in the recorder, and push the battery in completely. 2 Start recharging. Plug the DC plug of the AC adapter in the DC-IN terminal on the side of the recorder, and plug th...
Page 19 - Remaining Battery Power
Preparations (Continued) 99 Remaining Battery Power 1 According to the remaining battery power, the battery icon on the upper right corner of the LCD monitor varies as illustrated below: Remaining battery power: Change in the icon display 2 When the remaining battery power is running low, the “No Ba...
Page 20 - How to Use and Remove the Belt Clip; How to attach the belt clip
Preparations (Continued) 100 Convex (B) part of the belt Slit (2) How to Use and Remove the Belt Clip How to attach the belt clip 1 Remove the belt clip locking screw Remove the belt clip locking screw by turning it counterclockwise. 2 Attach the belt clip. Match the slit (1) in the reorder side wit...
Page 21 - How to remove the belt clip
Preparations (Continued) 101 How to remove the belt clip 1 Remove the belt clip locking screw Turn the Belt clip locking screw counterclockwise for removal. 2 Remove the belt clip. Press the C part of the belt clip in the arrowed direction while pressing the other side of the belt clip . 3 Attach th...
Page 22 - How to attach/detach the camera head; Attaching the Camera Head to the Recorder
Preparations (Continued) 102 How to attach/detach the camera head When attaching the camera head to the recorder, turn OFF the power supply to the recorder beforehand. Attaching the Camera Head to the Recorder 1 Remove the rubber cover. Remove the rubber cover from the camera head attaching connecto...
Page 23 - Removing the Camera Head; Waterproof function of this recorder
Preparations (Continued) 103 Removing the Camera Head 1 Remove the camera head. Turn the screw lock of the head connector counterclockwise to remove the camera head, and attach the rubber cover. Waterproof function of this recorder The camera head section of this recorder is waterproof. Note with ca...
Page 24 - How to Load and Unload the SD Memory Card; How to load the SD memory card
Preparations (Continued) 104 How to Load and Unload the SD Memory Card When loading or unloading the SD memory card, turn OFF the power supply to the recorder beforehand, or the stored data could be lost. The file saved in the SD memory card could be corrupted or deleted or “write” function of the S...
Page 25 - Turn ON and Turn OFF the Power Supply; Turning ON the power supply; Turning OFF the power supply
105 Turn ON and Turn OFF the Power Supply Turning ON the power supply Before turning ON the power supply, be sure to load the SD memory card. ( Î P104) 1 Turn ON the power supply. Press [POW ER&HOLD] slide switch to the POW ER side for approx. 2 seconds. Then, the Startup screen appears on the L...
Page 26 - Setting to the hold state; “Click”
106 Setting to the hold state 1 Set to the hold state. Press the [POW ER&HOLD] slide switch to “HOLD” side until the switch is clicked. ※ When the recorder is set to the hold state, no other functions of the recorder are available. This helps prevent wrong operations during the recording or when...
Page 27 - Set the Date and Time
107 Set the Date and Time When the power supply to the recorder is turned ON for the first time after purchase, the Date and Time Setting screen appears. Then, set the date and time according to the procedures below. 1 Move the cursor. To move forward the cursor, press [ENTER]. To move backward the ...
Page 28 - Recording; How to record
108 This is convenient for quick start when the camera direction adjustment or record setting is not required. Hold down [REC] to start recording. When shooting an important scene, be sure to try shooting beforehand and check the resolution, the video quality and the frame rate to see whether their ...
Page 30 - Changing the record settings
Recording (Continued) 110 Changing the record settings 1 Turn ON the power supply. ( Î P105) 2 Display the Record Mode setting screen. Press [REC] once to enter the Record mode, and then, press [MENU] to appear the Record Mode setting screen. 3 Select the record setting item. Move the cursor to the ...
Page 32 - Standard duration of recording
Recording (Continued) 112 Standard duration of recording [SD memory card capacity: 1GB] Record Mode: Video (No Audio) ※ Comparison table of approximate recording time. Frame rate Resolution Video quality 25 frames/sec 15 frames/sec 5 frames/sec 3 frames/sec 1 frames/sec High 34min 56min 2hr50min 4hr...
Page 33 - SD Memory Card M-Series made by Hagiwara Sys-Com
Recording (Continued) 113 The actual memory capacity and recording time of the SD memory card may depend on its manufacture or type. When the SD memory card of different capacity from 1GB is used, the recording time is roughly proportional to the capacity. The recording time of the SD memory card of...
Page 34 - Playing back the file; How to play the file
114 Playing back the file How to play the file 1 Turn ON the power supply ( Î P105) 2 Select the file Select the file to be played by using [ ∧ ] or [ ∨ ]. 3 Play the file Press [ENTER] to play the file. ※ When the playback ends, return to the Playlist screen. z Button operation during playback Fram...
Page 35 - Search mode
Playing back the file (Continued) 115 File exchange (Next file / Previous file) When the record mode for the playing file is set to [Video + Audio] or [Video], the mode can not be selected to [Audio only]. When the record mode for the playing file is set to [Audio only], the mode can not be selected...
Page 36 - Bookmark mode
Playing back the file (Continued) 116 Bookmark mode In the bookmark mode, when a favorite scene is checked with [ ] and [ENTER] is pressed, the checked favorite scene can be displayed instantaneously by using [ ∧ ] (UP) or [ ∨ ] (DOW N) z Button operation in the bookmark mode Button operation Functi...
Page 37 - Changing the play settings
Playing back the file (Continued) 117 Changing the play settings 1 Turn ON the power supply. ( Î P105) 2 Play the file. ( Î P114) 3 Display the play settings. Press [ENTER] in playback to pause the recorder. Then, press [MENU]. Then, the Play Setting OSD appears. 4 Select the play settings. Move to ...
Page 39 - Delete File
119 Delete File 1 Turn ON the power supply ( Î P105) 2 Select the file. Select the file to be operated on the Playlist screen by using [ ∧ ] or [ ∨ ]. 3 Display the OSD When [MENU] is pressed, the OSD appears. When [MENU] is pressed again, the OSD disappears 4 Select “Delete File.” Select “Delete Fi...
Page 40 - Using in Connection with External Devices; Attaching an external microphone to the recorder
120 Using in Connection with External Devices Attaching an external microphone to the recorder When attaching an external microphone to the recorder, turn OFF the power supply to the recorder beforehand. 1 Remove the rubber cover. Remove the cover from the external microphone terminal on the top of ...
Page 41 - Using in Connection with External Devices (Continued); Outputting video to the external monitor
Using in Connection with External Devices (Continued) 121 Outputting video to the external monitor When connecting the recorder with any external equipment, turn OFF the power supply to the recorder beforehand. 1 Connect the AV cable. Remove the rubber cover from the Earphone /AV output terminal, an...
Page 42 - Connection to the earphone; Connection to a speaker
Using in Connection with External Devices (Continued) 122 Connection to the earphone 1 Connect the earphone. Remove the rubber cover from the Earphone /AV output terminal, and connect the earphone. ※ The audio output of the recorder is monaural. The φ 3.5mm mini-plug can be used for earphone connect...
Page 43 - Changing Various Settings on the Setting Item Screen; How to change
123 Changing Various Settings on the Setting Item Screen How to change 1 Turn ON the power supply.( Î P105) 2 Display the setting items. Hold down [MENU] to display the setting items. 3 Select the setting item. Select the setting item by using [ ∧ ] (UP) or [ ∨ ] (DOW N), and press [ENTER]. When the...
Page 44 - Changing Various Settings on the Setting Item Screen (Continued); Setting Item List
Changing Various Settings on the Setting Item Screen (Continued) 124 Setting Item List Name Function 704 × 480 640 × 480 320 × 240 Resolution 160 × 128 To set the resolution High Standard Video Quality Low To set the video quality 25 frames/sec 15 frames/sec 5 frames/sec 3 frames/sec Frame Rate 1 fr...
Page 46 - SD card information
Changing Various Settings on the Setting Item Screen (Continued) 126 SD card information 1 Turn ON the power supply.( Î P105) 2 Display the setting items. Hold down [MENU] to display the setting items. 3 Select “SD Card.” Select the “SD card” by using [ ∧ ] or [ ∨ ], and press [ENTER]. Then, the SD ...
Page 47 - Format SD card
Changing Various Settings on the Setting Item Screen (Continued) 127 Format SD card 1 Turn ON the power supply.( Î P105) 2 Display the setting items. Hold down [MENU] to display the setting items. 3 Select “SD Card.” Select the “SD card” by using [ ∧ ] or [ ∨ ], and press [ENTER]. Then, the SD memor...
Page 48 - Firmware upgrade
Changing Various Settings on the Setting Item Screen (Continued) 128 Firmware upgrade For the purpose of enhancing the recording function, the recorder can upgrade the firmware (recorder operation program). Since this upgrading is to change the central function of the recorder, improper upgrading co...
Page 50 - Setting the Date and Time
Changing Various Settings on the Setting Item Screen (Continued) 130 Setting the Date and Time The date and time is saved in the recorded data. 1 Turn ON the power supply.( Î P105) 2 Display the setting items. Hold down [MENU]. 3 Select “Set Time.”( Î P107) 4 Set the date and time.( Î P107) In any o...
Page 52 - Replacing the Lens
132 Replacing the Lens The camera lens can be replaced by the optional lens. 1 Remove the lens cover. Remove the lens cover from the camera unit mounting bracket by turning the lens cover counterclockwise. 2 Remove the lens. Remove the lens from the camera unit mounting bracket by turning the lens c...
Page 53 - Adjusting the Focus
133 Adjusting the Focus Do not scrub the lens or give a shock to the lens, or the lens could be damaged or failed. Note that separation at any point other than the point where separation is permitted could cause failure. Apply grease to the O-ring of the camera unit mounting bracket. If the O-ring i...
Page 54 - Connection to the PC
134 Connection to the PC Connection to the PC The PC applicable to this import should have been installed with Microsoft Windows2000 (SP4 or newer) or XP (SP2 or newer). When connecting the recorder with the PC or upgrading, be sure to use both the AC adapter and the battery. 1 Connect the USB cable...
Page 55 - Browsing the files
Connection to the PC (Continued) 135 Do not unplug the USB cable until the file operation ends completely. The file can be renamed only on the PC. Select the file to be renamed, click [Name Change] on the File menu. After inputting a new name, press [ENTER]. Browsing the files The files in the SD me...
Page 56 - Troubleshooting
136 Troubleshooting ■ Battery and power source Symptom Cause Remedy The SUV-Cam cannot be turned ON. Does the battery have a charge? Use the attached AC adapter or charge the battery. ( Î P98) The battery runs out quickly after charging. The SUV-Cam is being used in a cold Climate If the recorder is...
Page 61 - Specification
141 Camera head main unit Water proofing IPX8 Total length 80cm or 150cm Mass 80cm ＝ Approx. 115g 150cm ＝ Approx. 150g Dimension diameter ： 20mm length ： 84.8mm Lens Focal length 3.8mm F number 2.0 Horizontal field angle 53.4° Vertical field angle 40.0° Focus adjustment Manual Shooting range 0....
Page 62 - Optional Accessories
142 Optional Accessories Optional accessories Camera head 80cm # 2614 Camera head 150cm # 2614-1 Battery pack # 2615 Lens f=6.0mm F2.5 # 2616 Lens f=8.0mm F2.0 # 1616-1 For the information of the optional accessories, ask the sales outlet from whom you have purchased this recorder or visit our websi...
Page 63 - Note
