Electrolux ESE6107SG - User Manual

Side by Side RefRigeRatoRS

iNStRUCtioNS

iNStRUCtioNS

Aligned to cupboard –

even gap

Top of refrigerator

is level – horizontal

Adjust front rollers for

unevenness of floor. e.g.

adjust this roller down.

Packing may be required

underneath the rear roller

to ensure stability.

4. If the appliance now rocks from one corner to the

opposite rear corner, this means that the floor is

uneven; you will need to put some packing under one

of the rear rollers.

5. You may now need to fine-tune the installation by

adjusting the front rollers once again.

adjUStiNg dooR aligNmeNt

Each door is independently adjustable in the vertical

direction by turning the adjustable bolts under the hinges

using the spanner provided.

Large plastic roller nut

Front roller

Adjusting bolt

The doors can be adjusted up or down. Depending on the

amount of adjustment required it may be sufficient to adjust

only one door (refer to following diagrams).

NOTE: When the height of the rollers and adjusting bolts

are correctly adjusted the refrigerator will stand firmly on

the floor and the doors will be in line with one another.

When correctly installed, your refrigerator should:

• Have adequate clearance to the back, sides and

top for air circulation

• Be aligned to the surrounding cupboards

• Have doors that will self close from a partially

open position

CleaRaNCeS aRoUNd yoUR RefRigeRatoR

Your Side by Side refrigerator can be installed between

cupboards or fixtures but you must allow for the following

spaces around the cabinet.

• Allow a minimum of 5mm clearance on both sides

(see diagram 1)

• Allow a minimum of 10mm clearance above hinge

covers (see diagram 1)

• Allow 10mm clearance at the back of the refrigerator

(see diagram 1)

Diagram 1

Recommended

minimum airspace

CABINET

5mm

10mm

10mm

5mm

DOORS

• If you place the refrigerator next to a wall, allow a

minimum clearance of 250mm for freezer side and

350mm for fridge side of the doors, this will allow

easy removal of shelves and bins for cleaning (refer to

diagram 2).

• The refrigerator is designed to sit proud of cupboards and

other fixtures. To enable doors to open fully, ensure that

other fixtures do not stick out further than the refrigerator

cabinet (see diagram 2).

iNStallatioN

The refrigerator should arrive with the front rollers wound

down. We recommend that the appliance be tilted

backwards by about 10mm to 15mm, this will allow the

doors to self close providing a consistent door seal.

To do this follow the instructions below.

Height adjustable

front rollers

Fixed rear rollers

10 –15mm

When you want to install your appliance, take the

following steps.

1. Roll the refrigerator into it’s final position.

WARNING

The rollers are designed for forward or backward

movement only. They are not castors. Moving the

refrigerator sideways may damage your floor and

the rollers.
2. If the refrigerator is not tilted back you can adjust the

two front rollers by adjusting the large plastic roller

nut. You may need two people, one to adjust rollers

and one to tilt the refrigerator slightly back to take the

weight of the appliance off the front rollers. This will

increase or decrease the height of the rollers. One

turn of the nut will change the tilt of the refrigerator by

approximately 5mm.

3. If the cabinet is level, then the side walls should be

plumb or vertical. If the cabinet is built in or partly built

in check the alignment of the cabinet side against

the cupboard.

Spanner

Spanner

iNteRNal paCkagiNg

1. Please remove all internal packaging material before

use. Any glue or tape residue or the like should be

removed with a solution of mild detergent and water.

2. Clean your appliance thoroughly and wipe off any dust

that has accumulated during shipping.

3. It is recommended that the refrigerator is kept upright at

all times. However if for any reason the refrigerator is laid

down, let it stand for a minimum of 1 hour before

turning on.

WARNING

Before cleaning: Remove the power cord from the power

socket. This will make sure there is no chance of getting

an electric shock.

4. Install accessories such as the egg tray. The

accessories are packed together to prevent damage

during delivery.

5. Plug your appliance into the power point.

6. We recommend that you let your refrigerator run for

two to three hours before you put any food in it. This

will allow you to check that it is operating properly

and that enough cool air is circulating.

Diagram 2

25

0mm

350mm

maximum

cupboard depth

iNStallatioN maNUal