Page 4 - receiver
4 0 1 QUick seT-Up: receiver 1. Do not connect the receiver to any other equipment yet! 2. Connect the two Antennas to the receiver. 3. Install the blades into the power supply, plug it into the back of the receiver, and into an outlet. 4. Press the POWER switch. Display will light up. 5. Press and ...
Page 5 - transMitter; Press the transmitter Power Switch until the display comes on.
5 QUick seT-Up: transMitter 1. With the Power switch on the transmitter OFF, install two fresh AA batteries into the transmitter. 2. Press the transmitter Power Switch until the display comes on. 3. Hold the transmitter with the EZsync Port facing the receiver, about a foot (30 cm) away. 4. Press th...
Page 6 - systeMs operation; should hear audio coming out of the system.; “Quick Set-up” is now complete. Please enjoy your r300 system.
6 QUick seT-Up: systeMs operation 1. Set the mixer/amp gain. 2. Talk or sing into the microphone or play the guitar at a normal volume. You should hear audio coming out of the system. 3. You may have to adjust the gain (via the control next to the connector on the receiver back panel) to provide the...
Page 7 - deTailed; receiVer cONTrOls, cONNecTOrs
7 SYNC R 300 EZ sync Clear SET EZ sync Clear Scan Electro-Voice R300 ANTENNA B ANTENNA A 12V .500mA MIN MAX VOLUME LEVEL -10dB 0dB BALANCED OUT UNBALANCED OUT deTailed coMponent descriptions 2.1 | r300 receiver receiVer cONTrOls, cONNecTOrs 1. Power ON/OFF 2. SYNC Data Transfer Button 3. Infrared EZ...
Page 8 - receiver setup & Operation
8 deTailed coMponent descriptions 2.1 | receiver setup & Operation 1. Place the receiver and antennas where there is a clear line of sight to the area where the transmitter will be used. Rotate the antennas to separate them by 90 degrees. 2. install the appropriate power connection blades into t...
Page 9 - direct sunlight before trying again.
9 e. Press the SYNC button on the receiver to transfer the channel information. f. The receiver will display SYNC until the data is transferred, then return to the main screen. g. The transmitter display screen will now show the new channel and frequency. h. If the channel data was not transferred t...
Page 11 - displaY
11 7. With the transmitter on, speak into the microphone or play the guitar. Turn up the level on the mixer or amplifier until you are able to hear the desired signal. If no audio is present, repeat setup and refer to the troubleshooting section. Note: It may be necessary to adjust the receiver outp...
Page 12 - This feature can be useful when the receiver is in a location where
12 deTailed coMponent descriptions 9. change lock-Out This feature can be useful when the receiver is in a location where unauthorized personnel have access to the receiver. With the LOCK ON, the channel cannot be changed and the word LOCK is displayed when the or button is pushed. a. Press and hold...
Page 14 - receiver Main Operating screen
14 deTailed coMponent descriptions 2.1.2 | receiver Main Operating screen display: 1. RF Signal Meter2. Audio Meter3. Lock Indicator4. No Signal Indicator5. Channel Number (01 to 32) or Frequency 6. Squelch Setting7. Antenna Diversity Status A or B antenna controls: 1. Press or to change channels2. ...
Page 15 - Handheld Transmitter
15 2.2 | Handheld Transmitter HT-300 CONTROLS, CONNECTORS AND INDICATORS1. Microphone Element2. Backlit LCD Display a. Channel b. Frequency c. Battery Level d. Mute Indicator 3. EZSync Infrared Port 4. Battery Cover – Screw type.5. Battery Compartment – Two AA Batteries6. On/Off/Mute button
Page 16 - Handheld Transmitter setup & Operation
16 deTailed coMponent descriptions 2.2 | Handheld Transmitter setup & Operation 1. insert batteries. a. Remove the battery compartment cover by unscrewing it completely. b. Insert two AA batteries as shown, sliding one up into the housing to make room for the other. 2. Turn the unit on by pressi...
Page 18 - bodypack Transmitter
18 deTailed coMponent descriptions 2.3 | bodypack Transmitter continued 5. LCD Display a. Channel b. Frequency c. Battery Level d. Mute Indicator 6. EZsync infrared window 7. Battery Compartment Latch – push down latch and slide cover as shown. 8. Two AA Battery Compartment – follow polarity as mark...
Page 20 - compatibility
20 GUideliNes AND RECOMMENDATIONS For Best Performance compatibility The transmitter and receiver must be of the same frequency band and set to the same channel in order to work together. The R300 is available in three frequency bands, A, B and E (Europe only). The band information is available in t...
Page 22 - problem
22 TrOUble SHOOTING GUIDE 0 4 problem possible causes solutions No audio and no display on the receiver Receiver is off Make sure that the power supply is properly connected and the on/off button is in the on position No audio and no RF signal indicator on the receiver display Transmitter is off Tur...
Page 24 - speciFicaTiONs
24 speciFicaTiONs r300 receiver Receiver Type Synthesized PLL Frequency Range (RF) A Band 618 – 634MHz B Band 678 – 694 MHz E Band 850 – 865 MHz Number of Channels 32 Modulation +/- 40 kHz Diversity Antenna RF Sensitivity < 1.0 μV for 12 dB SINAD Image Rejection > 55dB Squelch Tone Code plus A...
Page 25 - audio parameters
25 audio parameters Frequency Response 80 – 18kHz +/- 2dB Balanced Output 20 dBV (max @ 40 kHz deviation) Unbalanced Output Adjustable 8 mV to 0.755V RMS Distortion < 1.0%, 0.4% typical (ref 1kHz, 40kHz deviation) Signal-to-Noise Ratio > 100dB A Weighted Dynamic Range > 95dB Transmitters bp...
Page 26 - cerTiFicaTiONs; (Depending on frequency selected and country of operation)
26 cerTiFicaTiONs (Depending on frequency selected and country of operation) R300 receiver, HT-300 and BP-300 transmitters: Certified to ETSI EN 300 422-2 and ETSI EN 301 489-9, Conforms to European Union directives, eligible to bear CE marking as per the R&TTE directive. R300 receiver: Certifie...
Page 27 - EV Audio Service
27 FacTOrY SERVICE Factory service (North america) If factory service is required, ship the unit prepaid in its original carton to: EV Audio Service c/o Bosch Security Systems, Inc. 8601 East Cornhusker Highway Lincoln, NE 68507-9702 U.S.A. Tel: 402-467-5321 or 800-553-5992 Fax: 402-467-3279 Enclose...
Page 28 - accessories and parts
28 accessOries AND PARTS 0 8 accessories and parts Model # Order # R300-L System Uni Lapel ULM18 F.01U.168.803 R300-E System Headworn Microphone HM3 F.01U.168.804 Windscreen for ULM18 WS-18 F.01U.168.802 Windscreen for HM3 WS-H3 F.01U.170.778 Beltclip for BP-300 BC-300 F.01U.168.797 Guitar Cord MAC-...
Page 32 - Headquarters in Americas and Asia and Pacific rim addresses
32 americas: Headquarters Americas Bosch Security Systems, Inc. 12000 Portland Ave South, Burnsville, MN 55337, USA USA–Ph: 1-800-392-3497 Fax: 1-800-955-6831 canada: Ph: 1-866-505-5551 Fax: 1-866-336-8467 latin america: Ph: 1-952-887-5532 Fax: 1-952-736-4212 europe, africa & Middle-east: Headqu...
