Page 2 - CONTENTS; ENGLISH
CONTENTS ENGLISH IMPORTANT SAFETY INSTRUCTIONS ...... 3 IMPORTANT SERVICE INSTRUCTIONS ...... 3 DESCRIPTION ...... 4 Unpacking & Warranty ...... 4 Installation Notes ...... 4 FRONT PANEL ...... 5 Mains Switch ...... 5 Protect ...... 5 Limiter ...... 5 Level Indication ...... 5 Power ...... 5 REA...
Page 3 - SAFETY COMPONENT ( MUST BE REPLACED BY ORIGINAL PART ); IMPORTANT SERVICE INSTRUCTIONS
3 The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated „dangerous voltage“ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point wit...
Page 4 - DESCRIPTION
Congratulations on your ElectroVoice PA series power amplifier purchase! The ElectroVoice PA-Series power amp line combines outstanding audio performance, exceptional reliability and secure operational safety in a compact 2RU chassis design. All models in the PA Series provide several protection cir...
Page 5 - FRONT PANEL; Mains Switch; protection circuitry.; Limiter; loudspeaker systems from being damaged by probable overload.; Level Indication; protection circuit causes these indicators to go out.; Power
FRONT PANEL Mains Switch Use the mains switch to switch the unit’s power on. A soft-start function prevents inrush current peaks on the mains, additionally preventing the mains line protection switch from activating during the amp’s power-on operation. Loudspeaker outputs are activated via relay swi...
Page 6 - REAR PANEL; Audio Signal Inputs
REAR PANEL Audio Signal Inputs The electronically balanced inputs facilitate the connection of external signal sources (e.g. mixing consoles). When screwed to the power amp, the screwlock connectors provided with the unit prevent accidental disconnection. Choosing balanced cables (2 conductors for a...
Page 7 - minimal impedance of 4 ohms per channel.; Loudspeaker Outputs; mm
100V 25W 100V 25W 16 x 25W 100V 6W 100V 6W 66 x 6W PA2450L & PA4150L Loudspeaker systems connected to channels A and B (or C and D) have to be connected according to the polarity indicated. Please, make sure to mind the minimal impedance of 4 ohms per channel. For bridged operation, the load has...
Page 8 - Mains Fuse
REAR PANEL Mains Fuse Under normal circumstance, the mains fuse blows only in the event of failure. When replacing the fuse, make sure to use a fuse of the same type with identical amperage, voltage and blow characteristics. If the mains fuse blows repeatedly, please contact an authorized service ce...
Page 9 - MAINS OPERATION & RESULTING TEMPERATURE; Mains Operation
MAINS OPERATION & RESULTING TEMPERATURE Mains Operation The following tables provide a useful aid in determining power supply and cabling requirements. Column “1/8 max. output power into 4 ohms (2) ” states the values to be used for normal operation. These results were measured with the power am...
Page 10 - Sine wave 1kHz
MAINS OPERATION & RESULTING TEMPERATURE PA2400T - 100V output Umains [V] Imains [A] Pmains [W] Pout [W] PD [W] BTU/ hr (3) idle 230 0,3 44,3 0 44 151 Max. output power into 25ohms (1) 230 8,9 1643 2x430 783 2672 1/3 max. output power into 25ohms (1) 230 5,5 952 2x143 665 2270 1/8 max. output pow...
Page 11 - NOTES
Page 12 - INHALT
INHALT WICHTIGE SICHERHEITSHINWEISE ....................... 13 WICHTIGE SERVICEHINWEISE ....................... 13 BESCHREIBUNG ....................... 14 Auspacken & Garantie ....................... 14 Installationshinweise ....................... 14 FRONTSEITE ....................... 15 Netzsc...
Page 14 - BESCHREIBUNG
15 Herzlichen Glückwunsch! Sie haben sich mit einer Endstufe von Electro-Voice für ein Gerät modern- ster Technologie entschieden. Die Endstufen der PA-Serie vereinen überragende Audio Performance mit höchster Zuverlässigkeit und Betriebssicherheit. Zahlreiche Schutzschaltungen, die für jeden Kanal ...
Page 15 - FRONTSEITE; Netzschalter; dieser Verzögerung die Protect LED.
15 FRONTSEITE Netzschalter Mit dem Netzschalter wird das Gerät eingeschaltet. Eine Softstart-Schaltung vermei- det dabei Einschaltstromspitzen auf der Netzleitung. Dadurch wird verhindert, dass der Leitungsschutzschalter des Stromnetzes beim Einschalten der Endstufe anspricht. Die Lautsprecher werde...
Page 16 - RÜCKSEITE; Signaleingänge
16 17 RÜCKSEITE Signaleingänge An den elektronisch symmetrischen Eingängen werden die Signalquellen (z.B. Mischpult) angeschlossen. Die im Lieferumfang enthaltenen Steckverbinder können mit der End- stufe verschraubt werden um ein versehentliches Entfernen zu verhindern. Die verwendeten NF-Kabel sol...
Page 17 - Lautsprecherausgänge; cherlinien ist möglich.
16 17 100V 25W 100V 25W 16 x 25W 100V 6W 100V 6W 66 x 6W PA2450L & PA4150L Lautsprecher für Kanal A & B (bzw. C & D) werden entsprechend der angege- benen Polarität angeschlossen. Beachten Sie, dass die minimale Impe- danz für jeden Kanal 4 Ohm beträgt. Für den Brückenbetrieb muß die Las...
Page 18 - Netzsicherung
18 19 RÜCKSEITE Netzsicherung Die Netzsicherung löst unter normalen Umständen nur bei einem Fehlerfall aus. Die Sicherung darf nur gegen eine gleichwertige Sicherung mit gleicher Strom-, Spannungs- und Auslösecharakteristik getauscht werden. Sollte die Netzsicherung wiederholt durchbrennen, kontakti...
Page 19 - NETZBETRIEB & WÄRMEENTWICKLUNG; Netzbetrieb; der Aussteuerungsgrenze betrieben wird.; Wärmeentwicklung in der Endstufe; zeigt die abgegebene Wärmemenge je Stunde.
18 19 NETZBETRIEB & WÄRMEENTWICKLUNG Netzbetrieb Mit Hilfe der folgenden Tabellen können die Anforderungen für Stromversorgung und Zuleitungen bestim- mt werden. Für normalen Betrieb können die Werte der Spalte „1/8 max. Ausgangsleistung an 4Ohm (2) “ verwendet werden. Die Endstufe wurde hier mi...
Page 20 - Sinusaussteuerung 1kHz
20 21 NETZBETRIEB & WÄRMEENTWICKLUNG PA2400T - 100V Ausgang UNetz [V] INetz [A] PNetz [W] PAus [W] PV [W] BTU/ hr (3) Leerlauf 230 0,3 44,3 0 44 151 Max. Ausgangsleistung an 25Ohm (1) 230 8,9 1643 2x430 783 2672 1/3 max. Ausgangsleistung an 25Ohm (1) 230 5,5 952 2x143 665 2270 1/8 max. Ausgangsl...
Page 21 - NOTIZEN
Page 22 - TABLE DES MATIÉRES
TABLE DES MATIÉRES INSTRUCTIONS DE SÉCURITÉ IMPORTANTES ....................... 23 INSTRUCTIONS DE RÉPARATION IMPORTANTES ....................... 23 INTRODUCTION ....................... 24 Déballage et garantie ....................... 24 Remarques concernant l’installation ....................... 24...
Page 23 - INSTRUCTIONS DE SÉCURITÉ IMPORTANTES; COMPOSANT DE SÉCURITÉ (DOIT ÊETRE REMPLACÉ PAR UNE PIÈCE; INSTRUCTIONS DE RÉPARATION IMPORTANTES
23 INSTRUCTIONS DE SÉCURITÉ IMPORTANTES Le symbole représentant un éclair fléché dans un triangle équilatéral a pour but d’alerter l’utilisateur de la présence d’une „tension dangereuse“ non isolée à l’intérieur du boîtier, pouvant être d’une force suffisante pour constituer un risque d’électrocutio...
Page 24 - INTRODUCTION
Félicitations ! En achetant un amplificateur de puissance Electro-Voice vous avez choisi un appareil employant la technologie la plus avancée qui soit. Les amplificateurs de puissance PA-Series associent des performances audio inégalées, à un fonctionnement fiable et durable. Les différents circuits...
Page 25 - FACE AVANT; Interrupteur secteur; Utilisez l’interrupteur secteur; Limiteur; ne soient endommagés par une probable saturation.; Indicateur de niveau
FACE AVANT Interrupteur secteur Utilisez l’interrupteur secteur pour mettre l’appareil sous tension. La fonction de temporisation Soft-Start le protège des sautes de courant, ce qui de plus évite l’activation du circuit de protection interne lors de la mise sous tension. Les sorties haut- parleur so...
Page 26 - PANNEAU ARRIÈRE; Entrées Signal Audio
PANNEAU ARRIÈRE Entrées Signal Audio Les entrées symétrisées électroniquement facilitent la connexion de sources de signal externes (ex. des consoles de mixage). Lorsqu’ils sont vissés à l’ampli de puissance, les connecteurs à vis fournis avec l’appareil empechent tout débranchement accidentel. Il e...
Page 27 - utiliser uniquement des câbles du commerce.
100V 25W 100V 25W 16 x 25W 100V 6W 100V 6W 66 x 6W PA2450L & PA4150L Les haut-parleurs connectés aux canaux A et B (ou C et D) doivent être branchés en respectant la polarité indiquée. Veuillez vous assurer qu’il y a bien une impédance minimale de 4 ohms par canal. Pour le fonctionnement en mode...
Page 29 - ALIMENTATION SECTEUR ET TEMPÉRATURE RÉSULTANTE; Fonctionnement sur le secteur
ALIMENTATION SECTEUR ET TEMPÉRATURE RÉSULTANTE Fonctionnement sur le secteur Les tableaux suivants vous apporteront une aide précieuse dans la détermination du choix de l’alimentation et des câbles. La colonne “1/8 max. output power into 4 ohms (2) ” indique les valeurs à utiliser pour un fonctionne...
Page 30 - Onde sinus 1 kHz
ALIMENTATION SECTEUR ET TEMPÉRATURE RÉSULTANTE 30 PA2400T - 100V output Umains [V] Imains [A] Pmains [W] Pout [W] PD [W] BTU/ hr (3) idle 230 0,3 44,3 0 44 151 Max. output power into 25ohms (1) 230 8,9 1643 2x430 783 2672 1/3 max. output power into 25ohms (1) 230 5,5 952 2x143 665 2270 1/8 max. outp...
Page 31 - NOTICES
Page 32 - TECHNICAL SPECIFICATIONS
32 33 TECHNICAL SPECIFICATIONS � � �� �� � � � �� �� � � � �� �� � � � �� �� � � � �� �� � �� �� �� �� �� �� � � � � � � � � � � � � � �� �� �� � �� � � � � � �� �� �� � �� � �� �� �� � �� � � �� �� �� � �� �� �� �� �� �� �� � �� � � � �� � �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ...
Page 37 - DIMENSIONS; PA series amplifier dimensions in mm.
36 37 DIMENSIONS PA series amplifier dimensions in mm.