Page 3 - CONTENTS
CMY Zoom 575™ ©Elation Professional® 3 CMY Zoom 575™ CONTENTS 1. General Information……………………………………………………………………… 3 a. Introduction………………………………………………………………………. 3 b. Unpacking………………………………………………………..…………..… 3 c. Customer Support…………………………………………….………………… 3 d. Warranty Registration……………………………………………………..……...
Page 4 - GENERAL INFORMATION; INTRODUCTION
CMY Zoom 575™ ©Elation Professional® 4 CMY Zoom 575™ 1. GENERAL INFORMATION INTRODUCTION : Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The CMY Zoom 575,™ has been designed to perform reliably for years when the guidelines in...
Page 5 - WARRANTY REGISTRATION
CMY Zoom 575™ ©Elation Professional® 5 CMY Zoom 575™ Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION : The CMY Zoom 575™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchas...
Page 6 - Never open this fixture while in use!
CMY Zoom 575™ ©Elation Professional® 6 CMY Zoom 575™ Thus, lamp should always be replaced at the end of their recommended duty cycle. Extreme caution should be used when operated this or any fixture fitted with a gas discharge lamp. Never open this fixture while in use! During the initial operation ...
Page 7 - SAFETY INSTRUCTIONS; any service related issues.
CMY Zoom 575™ ©Elation Professional® 7 CMY Zoom 575™ 2. SAFETY INSTRUCTIONS The CMY Zoom 575™ is an extremely sophisticated piece ofelectronic equipment. To guarantee a smooth operation, it isimportant to follow the guidelines in this manual. Themanufacturer of this device will not accept responsibi...
Page 8 - may increase the risk of damage and/or personal injury.; Never look directly into the light source,
CMY Zoom 575™ ©Elation Professional® 8 CMY Zoom 575™ may increase the risk of damage and/or personal injury. 10. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture. 11. Do not attempt to operate this fixture if the power cord has become damaged or frayed. Important N...
Page 10 - GENERAL GUIDELINES; manufactures warranty.
CMY Zoom 575™ ©Elation Professional® 10 CMY Zoom 575™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, etc. Do not attempt operation or installation without a proper knowledge on how to so. This fixture was designed for indoo...
Page 11 - LAMP INSTALLATION INSTRUCTIONS; Installing or replacing the lamp; Only install the lamp with the device unplugged from the mains.; never touch the lamp when it is hot.; Installation Procedure:; found on the bottom plate of the fixture.
CMY Zoom 575™ ©Elation Professional® 11 CMY Zoom 575™ 5. LAMP INSTALLATION INSTRUCTIONS Installing or replacing the lamp Only install the lamp with the device unplugged from the mains. The lamp has to be replaced when it is damaged or deformed. Before replacing the lamp, be sure the unit has had amp...
Page 12 - Do not operate this device with open cover; Lamp Optimization
CMY Zoom 575™ ©Elation Professional® 12 CMY Zoom 575™ equivalent). Please remember there is only one way to insert the lamp and the lamp should fit completely in the lamp socket. 5. Once the lamp has been inserted into the socket, gently slide the socket assembly back into place and secure with the ...
Page 13 - adjustment screws (
CMY Zoom 575™ ©Elation Professional® 13 CMY Zoom 575™ adjustment screws ( "1, 2, 3”) counterclockwise turn until the light is bright and evenly distributed. Please remember that a MSD 575/2 lamp is not a hot-restrike lamp therefore, you should wait at least 15 minutes before attempting to strike...
Page 14 - MOUNTING and INSTALLATION; areas were the fixture might be reached by unauthorized personal.; Before taking into operation for the first time,; Mounting; qualified staff should attempt installation.
CMY Zoom 575™ ©Elation Professional® 14 CMY Zoom 575™ 6. MOUNTING and INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were the fixture might be reached by unauthorized personal. Before mounting the fixture to any surface, make...
Page 15 - Mounting points
CMY Zoom 575™ ©Elation Professional® 15 CMY Zoom 575™ Mounting points Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and t...
Page 16 - Clamp Mounting
CMY Zoom 575™ ©Elation Professional® 16 CMY Zoom 575™ Clamp Mounting The CMY Zoom 575™ provides a unique mounting bracket assembly that integrates the hanging yoke as well as the safety cable rigging point in one unit (see the illustration below). When mounting this fixture to truss be sure to secur...
Page 17 - and female 3-pin XLR connector on either end of the cable.; DMX-512 control connection
CMY Zoom 575™ ©Elation Professional® 17 CMY Zoom 575™ 7. Understanding DMX Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): Your fixture and your DMX controller require a standard 3-pin XLR connector for data input and data output (see figure below). If you are constructing ...
Page 18 - DMX-512 connection with DMX terminator
CMY Zoom 575™ ©Elation Professional® 18 CMY Zoom 575™ other side to the male 3-pin XLR input of the moving head (Please refer to the diagram below.). You can chain multiple moving heads together through serial linking. The cable needed should be two conductor, shielded cable with XLR input and outpu...
Page 19 - Fixture DMX addressing
CMY Zoom 575™ ©Elation Professional® 19 CMY Zoom 575™ Fixture DMX addressing; All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture sta...
Page 20 - signal the display will flash
CMY Zoom 575™ ©Elation Professional® 20 CMY Zoom 575™ signal the display will flash "A.XXX" (XXX representing the actual DMX address). If your fixture is connected to a DMX controller and the display is flashing (not receiving a DMX signal), please check the following: - The 3 PIN XLR plug (...
Page 21 - DISPLAY LED INDICATORS
CMY Zoom 575™ ©Elation Professional® 21 CMY Zoom 575™ 8. DISPLAY LED INDICATORS The CMY Zoom 575™ has two LED indicators on the display. These indicators are designed to give a quick visual indication of the fixtures’ status. The illustration below details the functionality of the LED indicators. . ...
Page 22 - Default settings are shaded.
CMY Zoom 575™ ©Elation Professional® 22 CMY Zoom 575™ 9. FIXTURE MENU On-Board System Menu: The CMY ZOOM 575™ comes with an easy to navigate system menu. This next section will detail the functions of each command in the system menu. LED Control Panel: The control panel located on the top, front of ...
Page 24 - Main Menu Functions
CMY Zoom 575™ ©Elation Professional® 24 CMY Zoom 575™ Main Menu Functions 0. ADDRESS MENU - AOO1 - A511 (Value) - This is where you set the fixtures DMX address. Setting/Changing the DMX Address After applying power to the CMY ZOOM 575™ the LED will display the fixture’s current DMX address immediat...
Page 25 - RUN
CMY Zoom 575™ ©Elation Professional® 25 CMY Zoom 575™ will test the color channel, changing the color one by one and show the rainbow effect with different speeds. Again please remember, there are 10 DMX channels, and all except channels 3, 6, and 10 can be tested 4. Press MODE/ESC to exit. 2. PLAY ...
Page 27 - COLR
CMY Zoom 575™ ©Elation Professional® 27 CMY Zoom 575™ COLR - When you activate this reset function, the fixture will only reset the color wheel motor. 1. Access the main menu. 2. Tap the UP button until “RESE” is displayed, press ENTER. 3. Tap the UP button until “COLR” is displayed, then press ENTE...
Page 28 - clear the lamp time every time you replace the lamp.
CMY Zoom 575™ ©Elation Professional® 28 CMY Zoom 575™ 2. Tap the UP button until “RESE” is displayed, press ENTER. 3. Tap the UP button until “OTHR” is displayed, press ENTER to confirm and begin the reset process. 4. Press MODE/ESC to return to the main menu. 5. TIME MENU - LIFE - Displays the fixt...
Page 29 - VALU
CMY Zoom 575™ ©Elation Professional® 29 CMY Zoom 575™ 3. Tap the UP button until “CLMP” is displayed, then press ENTER to reset the lamp running time. 4. Press MODE/ESC to return to the main menu. 6. MIC MENU - This function allows for electronic control of the internal microphone’s sound sensitivit...
Page 30 - – This menu option access all the special functions listed below.
CMY Zoom 575™ ©Elation Professional® 30 CMY Zoom 575™ 2. Tap the UP button until “DISP” is displayed. 3. Press ENTER, the display will show “VALU”. 4. Tap the UP button until ”D-ON” is displayed and tap the ENTER button. 5. Press the UP button to select “ON” to activate this function, or “OFF” to de...
Page 31 - RDMX; Fixture Settings
CMY Zoom 575™ ©Elation Professional® 31 CMY Zoom 575™ feature on and off. 1. Access the main menu. 2. Tap the UP button until “SPEC” is displayed, press ENTER. 3. Tap the UP button until “LAAU” is displayed, press ENTER. 4. The display will show “ON/OFF.” 5. Press the UP button to display “ON” to ac...
Page 32 - DLOF
CMY Zoom 575™ ©Elation Professional® 32 CMY Zoom 575™ 2 to a value of “7” and use channel 3 to set your address to 57 by selecting a channel value of 57. Example 2: If you want to set the starting address to 420, set channel 1 to a value of “7,” channel 2 to "8" and channel 3 to "164"...
Page 33 - DFSE; When you confirm this function, the fixture will begin to; FANS
CMY Zoom 575™ ©Elation Professional® 33 CMY Zoom 575™ 1. Access the main menu. 2. Tap the UP button until “SPEC” is displayed, press ENTER. 3. Tap the UP button until “DFSE” is displayed, press ENTER. 4. The display will show “ON/OFF.” 5. Press the UP button to display “ON” to activate this function...
Page 34 - VER
CMY Zoom 575™ ©Elation Professional® 34 CMY Zoom 575™ 5. Press UP or DOWN button to select “HIGH” or “AUTO”. 6. Press ENTER to confirm. 7. Press MODE/ESC to return to the main menu. VER - Use this function to display the Software version of the unit. 1. Access the main menu. 2. Tap the UP button unt...
Page 36 - STEP
CMY Zoom 575™ ©Elation Professional® 36 CMY Zoom 575™ STEP - With this function you can program the number of steps in your individual Program. 1. Access the main menu. 2. Tap the UP button until “EDIT” is displayed, press ENTER. 3. Tap the UP button until “STEP” is displayed, press ENTER. 4. The di...
Page 37 - CEDT
CMY Zoom 575™ ©Elation Professional® 37 CMY Zoom 575™ 5. The display will show the DMX value for the channel that is being edited. It will be displayed as “07XX,” it stands for Channel 7 of the editing scene, the DMX value is “XX.” 6. Adjust the DMX value by tapping the UP button, until you get the ...
Page 39 - The chart below details the channel layout for 11 DMX channels.
CMY Zoom 575™ ©Elation Professional® 39 CMY Zoom 575™ 10 . DMX CHANNEL TRAITS The chart below details the channel layout for 11 DMX channels. CHANNEL 1: Color Wheel CHANNEL 2: Cyan Filter CHANNEL 3: Magenta Filter CHANNEL 4: Yellow Filter CHANNEL 5: Strobe Control CHANNEL 6: Mechanical Dimmer CHANNE...
Page 40 - DMX channel function and values:; Shutter closed; Channel 6 – Dimmer intensity:; Full beam
CMY Zoom 575™ ©Elation Professional® 40 CMY Zoom 575™ DMX channel function and values: Channel 1 - Color Wheel: 0-15 Open / white 16-31 Red32-47 Blue48-63 Green64-79 Light Yellow80-95 UV filter 96-111 CTB 112-127 CTO 128-189 Forwards rainbow effect from fast to slow190-191 No rotation192-255 Backwar...
Page 41 - Channel 9 - Color macros - CMY and color wheel; Off
CMY Zoom 575™ ©Elation Professional® 41 CMY Zoom 575™ Channel 8 - Zoom: 0-255 Zoom 27 - Zoom 19 Channel 9 - Color macros - CMY and color wheel 0-7 Off 8-15 Macro1 16-23 Macro224-31 Macro332-39 Macro440-47 Macro548-55 Macro656-63 Macro764-71 Macro872-79 Macro980-87 Macro1088-95 Macro11 96-103 Macro12...
Page 42 - Color change normal
CMY Zoom 575™ ©Elation Professional® 42 CMY Zoom 575™ 246-255 No function Channel 11 – Lamp on/off, reset, internal programms 0-19 Color change normal 20-39 Color change to any position40-59 Lamp on60-79 Lamp switch off80-84 All motor reset85-87 No function88-90 Colors motor reset91-93 No function94...
Page 43 - persist after a second attempt a third attempt will be made.
CMY Zoom 575™ ©Elation Professional® 43 CMY Zoom 575™ 11. ERROR CODES: When power is applied, the unit will automatically enter a “reset/test” mode. This mode brings all the internal motors to a home position. If there is an internal problem with one or more of the motors an error code will flash in...
Page 45 - CLEANING AND MAINTENANCE; The following points have to be considered during the inspection:
CMY Zoom 575™ ©Elation Professional® 45 CMY Zoom 575™ 12. CLEANING AND MAINTENANCE The following points have to be considered during the inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury...
Page 48 - PHOTOMETRIC DATA
CMY Zoom 575™ ©Elation Professional® 48 CMY Zoom 575™ 14. PHOTOMETRIC DATA
Page 49 - DIMENSIONAL DRAWINGS
CMY Zoom 575™ ©Elation Professional® 49 CMY Zoom 575™ 15. DIMENSIONAL DRAWINGS
Page 50 - CIRCUIT SCHEMATIC
CMY Zoom 575™ ©Elation Professional® 50 CMY Zoom 575™ 16. CIRCUIT SCHEMATIC
Page 51 - TECHNICAL SPECIFICATIONS; or; Fuse protection; Subtractive Color Mixing with CMY Dichroic Flags; manual are subject to change without any prior written notice.
CMY Zoom 575™ ©Elation Professional® 51 CMY Zoom 575™ 18. TECHNICAL SPECIFICATIONS Power supply:Operating Voltage _98VAC, 50Hz; _ 120VAC, 50Hz; _ 208VAC, 50Hz; _ 220VAC, 50Hz; _ 230VAC, 50Hz; _ 240VAC, 50Hz; or _ 98VAC,60Hz; _ 120VAC,60Hz; _ 208VAC,60Hz; _ 220VAC,60Hz; _ 230VAC,60Hz; _ 240VAC,60Hz; ...
Page 52 - Elation Professional
CMY Zoom 575™ ©Elation Professional® 52 CMY Zoom 575™ Elation Professional 4295 Charter Street Los Angeles, CA. 90058 323-582-3322 / 323-582-3108 fax www.ElationLighting.com /[email protected]
