Elation 1200C - Manual

Elation 1200C

Elation 1200C – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
Page: / 64

Table of Contents:

  • Page 3 – CONTENTS
  • Page 4 – GENERAL INFORMATION; INTRODUCTION
  • Page 5 – recycle whenever possible.
  • Page 6 – Never open this fixture while in use!
  • Page 7 – SAFETY INSTRUCTIONS; injuries and/or damage to the fixture.
  • Page 8 – may increase the risk of damage and/or personal injury.
  • Page 10 – GENERAL GUIDELINES; manufactures warranty.
  • Page 11 – Tilt Locking Mechanism
  • Page 12 – LAMP INSTALLATION INSTRUCTIONS; Safety Regulations; exposure to harmful UV radiation!; Installation Procedure:; “D” found on the back plate of the head assembly to access the lamp.
  • Page 13 – Do not attempt to operate this fixture without the protective; Lamp Optimization
  • Page 15 – MOUNTING AND INSTALLATION; areas were unauthorized personnel might reach the fixture.
  • Page 16 – Mounting points
  • Page 17 – Clamp Mounting; assembly; Securing the Design Beam 1200CTM
  • Page 18 – UNDERSTANDING DMX; Never
  • Page 19 – you may omit pins 4 and 5, see the illustration below.
  • Page 20 – DMX-512 connection with DMX terminator
  • Page 21 – show
  • Page 22 – ti
  • Page 23 – The lamp is struck when; rs; Changes
  • Page 25 – “Select program”; section of the control menu. You can set the number of steps under; “Edit program”; . You can edit the individual scenes under; “Edit scenes”; With this function, you can run the internal program via sound.
  • Page 26 – will remain in the fixtures memory indefinitely.
  • Page 29 – No DMX Status –; This function allows you to invert all pan movements. Use the Up and; Pan Degree –; This function changes the order of the DMX channels to more; Mic Sensitivity –; These adjustments and settings should only be performed by a
  • Page 31 – This function should only be performed by a qualified technician.
  • Page 32 – be entered each time the calibration menu function is entered.
  • Page 33 – Setting the DMX address -
  • Page 34 – Controller Settings
  • Page 35 – Operating Modes
  • Page 37 – Using the Built-In Wireless DMX System; When the WDMX system is activate the link between the built-in; Never connect a fixture to a controller via a DMX cable when the; transmitter to your DMX controller.
  • Page 38 – DMX signal from a controller.
  • Page 39 – DMX compliant controller.
  • Page 40 – Step 1B – Building Scenes from an External DMX Controller.
  • Page 41 – Step 2 – Editing Programs.
  • Page 44 – Auto Pro Part 1 is Program 2
  • Page 46 – DMX channel function and values:; Value; Pan Fine 16bit
  • Page 47 – Cyan Color Fine :
  • Page 48 – Fixed gobo indexing Fine
  • Page 49 – Fine Dimmer intensity:
  • Page 51 – FUSE REPLACEMENT; electronics and the other protects the lamp circuitry.
  • Page 52 – Pan Er
  • Page 54 – is not located in the default position after the reset.; CTO color Er; in the default position after the reset.; Color wheel Er; Focus Er; the default position after the reset.; Effect Wheel Er; located in the default position after the reset.
  • Page 55 – CLEANING AND MAINTENANCE; The following points have to be considered during the inspection:
  • Page 60 – CIRCUIT SCHEMATIC
  • Page 61 – TECHNICAL SPECIFICATIONS; Philips Gold MSR 1200 FastFit
  • Page 64 – Elation Professional
Loading the manual

Rev. 12/30/2008-visage Version v1.1





Elation Professional

6122 S Eastern Ave

Los Angeles, Ca 90040

www.elationlighting.com

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - CONTENTS

Design Beam 1200C™ ©Elation Professional® 3 Design Beam 1200C™ CONTENTS 1. General Information……………………………………………………………………… 4 a. Introduction………………………………………………………………………. 4 b. Customer Support…………………………………………….………………… 3 c. Warranty Registration……………………………………………………..……. 5 d. Discharge Lamp Warning………………...

Page 4 - GENERAL INFORMATION; INTRODUCTION

Design Beam 1200C™ ©Elation Professional® 4 Design Beam 1200C™ 1. GENERAL INFORMATION INTRODUCTION : Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Design Beam 1200C,™ has been designed to perform reliably for years when th...

Page 5 - recycle whenever possible.

Design Beam 1200C™ ©Elation Professional® 5 Design Beam 1200C™ Please do not discard the shipping carton in the trash, keep for warranty repair. Please recycle whenever possible. WARRANTY REGISTRATION : The Design Beam 1200C™ carries a two year (730 days) limited warranty. Please fill out the enclos...

Other Elation Models

All Elation Other