Page 3 - Table of Contents
ii Table of Contents EZ 250 Parts List 1 Items Provided by Installer 2 Preloaded Eiki Code 3 Preloaded Timer 4 EZ 250 Layout 5 EZ 250 Software Installations 6 Programming EZ 250 7-17 Labeling Buttons 18-19 Installing EZ 250 20-24 DIP Switch Settings 25 EZ 250 Software Troubleshooting 26 EZ 250 Opera...
Page 6 - Items Provided by Installer
- 2 - Items Provided by Installer • If you are going to need to program the EZ-250, a DB 9 serial cable to connect your computer to EZ 250 • Slotted screw driver • Hex driver • 2 pieces of standard Cat 5 cables to run between the EZ 250 and EZlink Hub • The control cable that was included with the p...
Page 7 - Preloaded Eiki Code
- 3 - Preloaded Eiki Code PLUG AND PLAY SET UP Your EZ-250 system is set to operate right out of the box. It has been pre-configured to work with the current line of EIKI projectors. If you are using one of the projectors listed below simply connect the control cable from the projector to the RS-232...
Page 8 - Preloaded Timers; button 9; down for
- 4 - Preloaded Timers The controller is preloaded with different timers that will turn off the projector after a specified period. This function can be selected by pressing button 9 down for 30 seconds, after the button starts to blink, continue pressing the button down. The button will blink once ...
Page 10 - EZ 250 software Installation
- 6 - EZ 250 software Installation 1. Goto http://www.eiki.com 2. Then select EZ 250 Software 3. Save to your PC 4. Then install the program from your desktop
Page 11 - Programming using a Saved file; Select EZ 250 under EIKI by clicking on the start menu, then all
- 7 - Programming EZ 250 (Best viewed in 1024 x 768 or higher) 1. To connect your EZ 250 controller to your EZlink Hub interface take two (2) standard cat5 cables and connect the first cable between EZlink 1 port on the interface and EZ 1 port on the controller and the second cable to the EZlink 2 p...
Page 12 - located on the back of the EZ 250); Standard Programming
- 8 - Reset Button Reset Button 5. Select open Note: a pre-existing file may be modified for current user specs once it is opened. 6. Select the Upload New Configuration to Control Button Or 7. The software will prompt you to press the reset button. (reset button is located on the back of the EZ 250...
Page 13 - Select Manufacturer
- 9 - Reset Button 5. Select Manufacturer 6. Select Model this will provide default codes to the EZ 250 7. Press the Select Button 8. Select the Upload New Configuration to Control Button Or 9. The software will prompt you to press the reset button. (reset button is located on the back of the EZ 250...
Page 14 - Standard Programming for 2 Devices; Select Manufacturer
- 10 - Reset Button 10. After the programming status disappears disconnect the cables from the computer and press the reset button on the back of the EZ 250 and you are ready for the installation of the EZ 250 Standard Programming for 2 Devices 1. Same as steps 1 thru 7 in Standard Programming 2. Se...
Page 15 - Standard Programming for a LSE device and a another Device; Select Upload New Configuration to Control
- 11 - Reset Button Reset Button 9. Press the Select Button 10. Select the Upload New Configuration to Control Button Or 11. The software will prompt you to press the reset button. (reset button is located on the back of the EZ 250) 12. After the programming status disappears disconnect the cables f...
Page 16 - Advanced Programming; Control
- 12 - Reset Button Reset Button 5. The software will prompt you to press the reset button. (reset button is located on the back of the EZ 250) 6. After the programming status disappears disconnect the cables from the computer and press the reset button on the back of the EZ 250 and you are ready fo...
Page 17 - Selecting Contact Closure
- 13 - Reset Button Reset Button 4. The software will prompt you to press the reset button. (reset button is located on the back of the EZ 250) 5. After the programming status disappears disconnect the cables from the computer and press the reset button on the back of the EZ 250 and you are ready fo...
Page 18 - Custom Programming; Button Detail/Reconfigure button under each button
- 14 - Note: This will setup contacts to momentarily close when button is pushed. Contacts can be setup to latch. See the custom programming section of this manual to learn more. Custom Programming 1. Same as steps 1 thru 7 in Standard Programming 2. Type in the custom coding you need for each butto...
Page 19 - Enter the RS232 command then select OK
- 15 - Reset Button Reset Button 5. Enter the RS232 command then select OK 6. Select Upload New Configuration to Control Or 7. The software will prompt you to press the reset button. (reset button is located on the back of the EZ 250) 8. After the programming status disappears disconnect the cables ...
Page 20 - Timer Programming; contacted to the EZ 250 for the time you select.
- 16 - Timer Programming This Feature allows you to select a timer that will shut off the devices that are contacted to the EZ 250 for the time you select. 1. Select Timer 2. Select Setup 3. Type in how many hour(s) you need 4. Select OK 5. Example: a four hour timer - the devices that are connected...
Page 21 - Labeling Buttons; (Refer to EZloader button layout for placement of label)
- 17 - Labeling Buttons 1. Using scissors cut out the labels from sheet of transparencies (Refer to EZloader button layout for placement of label) 2. Remove the button cap from EZtrol’s front panel with a thin blade 3. With a thin blade lift the top up of the lens from the diffuser Diffuser Lens 4. ...
Page 23 - projector location
- 19 - Installation of EZ 250 Installing EZ 250 with ONE Device 1. Pull the two pieces of Cat 5 cable from the controller location to the data projector location 2. Place the EZlink interface near the data projector location. This is recommended because you will already have a 110v power outlet ther...
Page 24 - Installing EZ 250 with TWO Devices; the second device location
- 20 - Installing EZ 250 with TWO Devices 1. Follow steps 1 – 7 in Install EZ 250 with 1 device for the first device 2. For the second device pull a DB9 serial cable from the EZlink interface to the second device location 3. Connect the cable that is coming from the device into the port that you sel...
Page 27 - section. Then connect your device into the relays.
- 23 - Installing EZ 250 with the option of the contact closures 1. Follow the steps in “Installing EZ 250 with 1 Data Projector” or “Installing EZ 250 with 2 Data Projectors” or “Installing EZ 250 with a LSE Device and a Data Projector” to connect with your data projector. 2. Setup which button you...
