Eiki EIP-1 - Manual - manualsarea.com

Page 2 - Table of Contents; Safety Instructions

1 Table of Contents 1. Safety Instructions ··················································································· 2 2. The Projector ···························································································· 3 2.1 Features 3 2.2 Accessories 4 2.3 Appearance 5 3. Settin...

Page 3 - Safety instructions; Warning: Do not cover the lens while the lamp lights.

2 1. Safety instructions Before you use the projector, please read this manual thoroughly and comply with the safety instructions hereunder. Improper use may cause fire, electric shock, injuries, or reduce the life of your projector. Warning: Please ensure the projector is grounded properly by conne...

Page 4 - Incorporated; TI; single chip 0.7” DLP; Fully functional remote controller, can be used as a mouse

3 2. The projector 2.1 Features • With the modularized structure of the product, all you need is the main body when conducting a presentation, thereby making your job easier. • XGA model can receive signals with resolution up to 1280x1024. To ensure the output quality, please adjust the setup of you...

Page 7 - ) For displaying data only; Foot Adjuster button

6 3. Setting up the projector 3.1 How to connect the projector Depending on your purpose, you can select any of the following connection methods. 1) For displaying data only Find the M1DA-VGA+USB cable; connect M1DA connector to the main body; and connect VGA and USB connectors to the computer. Then...

Page 8 - Video Enhanced Adaptor; and choose terminals below to; Notes; Connecting to a Computer

7 2) For playing video with audio effects Connecting with the Video Enhanced Adaptor ; and choose terminals below to connect. 1. Power cord 2. VGA signal in port 3. USB mouse control 4. S-Video signal in port 5.6 Composite Video signal in port7.8 PC Audio In/Out port Notes 1. Please make sure that b...

Page 10 - Adjusting the altitude of the projected image; Please use the foot adjuster to adjust the height of projector.; Lower

9 3.3 Adjusting the altitude of the projected image Please use the foot adjuster to adjust the height of projector. Higher 1. Hold the foot adjuster button. 2. Raise the projector to the height you like; and then release the foot adjuster to fix the projector. Lower 1. Hold the foot adjuster. 2. Low...

Page 11 - Adjusting the focus and zoom; Zoom Ring

10 3.4 Adjusting the focus and zoom You can zoom in or out the image with the zoom ring. To enlarge the image size, please turn the zoom ring counter-clockwise. To reduce the image size, please turn the zoom ring clockwise. To adjust the focus of the image, please turn the focus ring until the image...

Page 13 - projector facing the screen.; Control panel and remote controller; Menu

12 4. How to use the projector This section covers the methods of using and adjusting the projector, as well as the methods of using the control panel, remote controller and menu. 4.1 Initial image adjustment 1 Please follow the previously stated steps to turn on the projector; and keep the projecto...

Page 15 - Power

14 - Remote controller Key Functions Freeze/Esc/L Press this key to freeze the image. Press again to clear the static image. Press this key to quit the menu if the menu is on the screen. In the remote-control mouse mode, this key works as the left key of mouse. Enter/R Please check page 13 “Auto/Ent...

Page 16 - Be sure to connect USB mouse cable to the; the; Auto

15 Mode Press this key and green LED indicator turns on. Then the remote controller can be used as a mouse. " Be sure to connect USB mouse cable to the computer and projector before using the remote controller as a mouse. Menu Please refer to page 13 “Menu” of “Control panel”. Source Select Anal...

Page 26 - Replacing the lamp; module retaining screws.

25 6.1 Replacing the lamp 30 hours before the end of the lamp’s life time, the warning message “Lamp life time is up! Replacement suggested!” will display on the screen. Please replace the lamp immediately. Steps: 1. Power off the projector. 2. Unplug the power cord. 3. Cool down projector for at le...

Page 27 - Common problems and trouble-shooting

26 7. Appendix 7.1 Common problems and trouble-shooting If you are having a problem with your projector, please check the following: If you still cannot solve the problem, please contact your local distributor or our service center. Q.: No image on the screen at all? Make sure that you have properly...

Page 28 - your computer or VCR.; menu to change colors.; Management; to adjust the projection

27 Q.: Image becomes blurred Adjust the focus ring of the projector. Make sure that distance between the screen and projector is adequate (1.45~10m) Q.: The colors projected by your projector look different from the colors of your computer or VCR. This is not a problem. You can adjust the brightness...

Page 30 - Input Terminal; USB; Output Terminal; watt speaker

29 Input Terminal DVI (M1DA) USB RGB (M1DA-D-Sub 15 pin) RS232 (M1DA) YPbPr (M1DA,VGA) S-Video Mini DIN 4 pin Audio: RCA Jack 3.5mm Mini Jack Composite Video (RCA Jack) Output Terminal 1 watt speaker * All specifications are subject to change without notice. This device complies with Part 15 of the ...

Eiki EIP-1 - Manual

Table of Contents:

Summary

Other Eiki Models