Page 2 - Linux Open Source Code
1 Copyright © by Edimax Technology Co, LTD. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemic...
Page 3 - This device is equipped with a USOC RJ11C connector.
2 Federal Communication Commission Interference Statement FCC Part 68 This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. You must provide this information ...
Page 4 - FCC Caution
3 equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase th...
Page 8 - Introduction; Features
7 Introduction Congratulations on purchasing this Wireless Broadband Router. This Wireless Broadband Router is a cost-effective IP Sharing Router that enables multiple users to share the Internet through an ADSL or cable modem. Simply configure your Internet connection settings in the Wireless Broad...
Page 13 - Note
12 Note :Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN. Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3 2b) Windows XP 1. Click the Start button and select Settings , then click Network Connection...
Page 16 - admin
15 Note :Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN. Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3. 3) Once you have configured your PCs to obtain an IP address automatically, the router’s DH...
Page 17 - HOME; page screen below will appear. The; Home; Page is divided; Quick Setup Wizard; and
16 6) The HOME page screen below will appear. The Home Page is divided into four sections, Quick Setup Wizard , General Setup , Status Info. and System Tools. Quick Setup Wizard (Chapter 1) Select your Internet connection type and then input the configurations needed to connect to your Internet Serv...
Page 18 - Chapter 1; Quick Setup; in the HOME page, you should see the screen below.
17 7) Click on Quick Setup Wizard (see chapter 1) to start configuring settings required by your ISP so that you can start accessing the Internet. The other sections (General Setup, Status Information and Tools) do not need to be configured unless you wish to implement/monitor more advance features/...
Page 19 - NEXT; : Different ISP’s require different methods of connecting to the
18 Parameter Description Set Time Zone Select the time zone of the country you are currently in. The router will set its time based on your selection. Time Server Address You can manually assign time server address if the default time server dose not work. Enable Daylight Savings The router can also...
Page 20 - Back; to return to the
19 Menu Description 1.1 Cable Modem Your ISP will automatically give you an IP address 1.2 Fixed-IP xDSL Your ISP has given you an IP address already 1.3 PPPoE Your ISP requires you to use a Point-to-Point Protocol over Ethernet (PPPoE) connection. 1.4 PPTP Your ISP requires you to use a Point-to-Po...
Page 21 - Clone; button to replace the WAN MAC
20 1.1 Cable Modem Choose Cable Modem if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name and MAC address (see screen below). Note : The Host Name and MAC address section is optional and you can skip this sectio...
Page 22 - when you have finished the configuration above.; Congratulations; ! You have completed the configuration for the Cable
21 Click < OK> when you have finished the configuration above. Congratulations ! You have completed the configuration for the Cable Modem connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. 1.2 Fixed-IP x...
Page 23 - ! You have completed the configuration for the Fixed-IP x
22 Click < OK> when you have finished the configuration above. Congratulations ! You have completed the configuration for the Fixed-IP x DSL connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. 1.3 PPPoE S...
Page 24 - ! You have completed the configuration for the PPPoE
23 Connection Type If you select “Continuous”, the router will always connect to the ISP. If the WAN line breaks down and links again, the router will auto-reconnect to the ISP. If you select “Connect On Demand”, the router will auto-connect to the ISP when someone want to use the Internet and keep ...
Page 27 - ! You have completed the configuration for the PPTP
26 Click < OK> when you have finished the configuration above. Congratulations ! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4. 1.5 L2TP Select L2TP ...
Page 28 - Enter the IP address of the ISP Gateway
27 Use the following The ISP gives you a static IP to be used IP address to connect to the L2TP server. IP Address This is the IP address that your ISP has given you to establish a L2TP connection. Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0) Gateway Enter the IP addre...
Page 29 - ! You have completed the configuration for the L2TP; Telstra Big Pond
28 Idle Time Out The WAN "idle timeout" auto-disconnect function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you...
Page 30 - Chapter 2; General Setup
29 Parameter Description User Name Enter the User Name provided by your ISP for the Telstra Big Pond connection Password Enter the Password provided by your ISP for the Telstra Big Pond connection User deside login server Select if you want to assign the IP of Telstra Big Pond’s login manually serve...
Page 34 - : If you forget your password, you’ll have to
33 Click < Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) 2.1.2 Password Settings You can change the password required to log into the broadband router's system web...
Page 35 - Enabled; box to enable the Remote Management
34 Click < Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) 2.1.3 Remote Management The remote management function allows you to designate a host in the Internet the ...
Page 47 - at the bottom of the screen to save the above
46 Clone MAC Click the “Clone MAC” button will copy the MAC address of your PC, that you are using to configure the AP, to the WLAN MAC. MAC address If you want to bridge more than one networks together with wireless LAN, you have to set this access point to “AP Bridge-Point to Point mode”, “AP Brid...
Page 64 - : Virtual Server function will have priority
63 Parameters Description Enable Virtual Server Enable Virtual Server. Private IP This is the LAN client/host IP address that the Public Port number packet will be sent to. Note: You need to give your LAN PC clients a fixed/static IP address for Virtual Server to work properly. Private Port This is ...
Page 66 - : Individual port numbers are separated by a
65 Parameters Description Enable Trigger Port Enable the Special Application function. Trigger Port This is the out going (Outbound) range of port numbers for this particular application Trigger Type Select whether the outbound port protocol is “TCP”, “UDP” or both. Public Port Enter the In-coming (...
Page 67 - selection box and then; Copy to; Example: Special Applications
66 Select an application from the Popular Applications selection. Once you have selected an application, select a location (1-10) in the Copy to selection box and then click the Copy to button. This will automatically list the Public Ports required for this popular application in the location (1-10)...
Page 68 - Parameters Default
67 ID Trigger Port Trigger Type Public Port Public Type Comment 1 28800 UDP 2300-2400, 47624 TCP MSN Game Zone 2 6112 UDP 6112 UDP Battle.net In the example above, when a user trigger’s port 28800 (outbound) for MSN Game Zone then the router will allow incoming packets for ports 2300-2400 and 47624 ...
Page 71 - : To enable the Firewall settings select; Enable; and click; Apply
70 Hop Count The number of hops (routers) to pass through to reach the destination LAN. Interface The interface that go to the next hop (router). Add a Rule Fill in the "Destination LAN IP", "Subnet Mask”, “Default Gateway”, "Hop Count" and "Interface" of the rule to be a...
Page 73 - Fill “IP Filtering Table” to filter PC clients by IP.
72 Parameters Description Deny If select “Deny” then all PCs will be allowed to access Internet accept for the PCs in the list below. Allow If select “Allow” then all PCs will be denied to access Internet accept for the PCs in the list below. Filter client PCs by IP Fill “IP Filtering Table” to filt...
Page 74 - Add PC; The description for this client PC rule.
73 Add PC Fill in “Client PC MAC Address” and “Comment” of the PC that is allowed to access the Internet, and then click “Add”. If you find any typo before adding it and want to retype again, just click "Reset" and the fields will be cleared. Remove PC If you want to remove some PC from the ...
Page 75 - Example: Access Control
74 Note: You need to give your LAN PC clients a fixed/static IP address for the Access Control rule to work properly. Client PC Service You can block the clients from accessing some Internet services by checking the services you want to block. Protocol This allows you to select UDP, TCP or both prot...
Page 76 - Enable/disable URL Blocking
75 2.7.2 URL Blocking You can block access to some Web sites from particular PCs by entering a full URL address or just keyword of the Web site. Parameters Description Enable URL Blocking Enable/disable URL Blocking Add URL Keyword Fill in “URL/Keyword” and then click “Add”. You can enter the full U...
Page 78 - : If there is a conflict between the Virtual
77 2.7.4 DMZ If you have a local client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, then you can open the client up to unrestricted two-way Internet access by defining a DMZ Host. The DMZ function allows you to re-direct all packets going to your WA...
Page 79 - Chapter 3; Status; View the Broadband router’s system log
78 Chapter 3 Status The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the connection status of the Broadband router's WAN/LAN interfaces, the current firmware and hardware version numbers, any illegal attempts to access your network, ...
Page 82 - IP Address; Subnet Mask; . It also shows whether the; DHCP
81 3.3 Device Status View the Broadband router’s current configuration settings. The Device Status displays the configuration settings you’ve configured in the Quick Setup Wizard/General Setup section. Parameters Description Device Status This page shows the Broadband router’s current device setting...
Page 83 - View the operation log of the system.; Save; > to a local file for further processing or; Clear; > to get the most updated
82 3.4 System Log View the operation log of the system. Parameters Description System Log This page shows the current system log of the Broadband router. It displays any event occurred after system start up. At the bottom of the page, the system log can be saved < Save > to a local file for fu...
Page 84 - > to a local file for further processing
83 3.5 Security Log View any attempts that have been made to illegally gain access to your network. Parameters Description Security Log This page shows the current security log of the Broadband router. It displays any illegal attempts to access your network. At the bottom of the page, the security l...
Page 85 - address and; MAC; address and Time Expired of each LAN; Refresh; button to get the most
84 3.6 Active DHCP Client View your LAN client's information that is currently linked to the Broadband router's DHCP server Parameters Description Active DHCP Client This page shows all DHCP clients (LAN PCs) currently connected to your network. The “Active DHCP Client Table” displays the IP address...
Page 86 - the counters of packets sent and received
85 3.7 Statistics View the statistics of packets sent and received on WAN, LAN and Wireless LAN. Parameters Description Statistics Shows the counters of packets sent and received on WAN, LAN and Wireless LAN.
Page 87 - Chapter 4; Tool; selection and proceed to the
86 Chapter 4 Tool This page includes the basic configuration tools, such as Configuration Tools (save or restore configuration settings), Firmware Upgrade (upgrade system firmware) and Reset. Parameters Description 4.1 Configuration Tools You can save the router’s current configuration, restore the ...
Page 89 - Firmware Upgrade; at the bottom of
88 4.2 Firmware Upgrade This page allows you to upgrade the router’s firmware Parameters Description Firmware Upgrade This tool allows you to upgrade the Broadband router’s system firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard di...
Page 91 - IP address; The router’s IP address is the one entitled; Default Gateway; Your PC’s MAC Address is the one entitled; Physical Address
90 Appendix A How to Manually find your PC’s IP and MAC address 1) In Window’s open the Command Prompt program 2) Type Ipconfig /all and <enter> • Your PC’s IP address is the one entitled IP address (192.168.1.77) • The router’s IP address is the one entitled Default Gateway (192.168.1.254) • ...
Page 92 - DNS Server IP Address:
91 Glossary Default Gateway (Router): Every non-router IP device needs to configure a default gateway’s IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out towards the...
