Edelbrock 72230 - Manual
Edelbrock 72230 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION; . Be sure that you connect the “FUEL”
- Page 3 – WIRING DIAGRAM
- Page 4 – ADJUSTING THE CONTROL MODULE; NEVER exceed the RPM limit of your
Page 1 of 4
2004 Edelbrock Corporation
Brochure #63-0131
Catalog #72230
Rev. 5/04
Please study these instructions carefully before installing your new Edelbrock Nitrous System.
Failure to
follow instructions will void warranty and may cause damage to parts and/or personal injury. If you have any questions
or problems, please call our
Technical Hotline at: 1-800-416-8628,
7:00 am - 5:00 pm, Pacific Standard Time, Monday
through Friday or e-mail us at
NOTE:
Before starting this project, be sure that the motorcycle is cool enough to work on and that the battery is
disconnected (negative cable first). Failure to disconnect the battery could result in electrical damage to the adjustable
control module and/or personal injury.
PRE-INSTALLATION
1.
Make sure that the Nitrous Module Housing is easily accessible. Remove any components from the motorcycle
that could be blocking access to the unit.
2.
Remove the Chrome Cover Plate from the Nitrous Module Housing unit by removing the four allen head bolts from
the top of the cover plate
(Fig. 1)
. Be sure to disconnect the wires routing to your arming switch, mounted on the
Chrome Cover Plate, to prevent damage when the cover is removed completely
(Fig. 2)
. This will allow you access
to the Control Module for the proper removal and installation of your new component.
ADJUSTABLE CONTROL MODULE
for Edelbrock Harley-Davidson Nitrous Systems
Kit #72230
INSTALLATION INSTRUCTIONS
3
Remove the wire clamp located on the inside of the backing plate
(Fig. 3)
.
4.
Disconnect all of the Nitrous Control Module wires from their destinations.
This entails disconnecting all of the following connections:
• Battery (red wire)
• Module ground (black wire)
• Tachometer lead (green wire)
• Single Fire or Dual Fire Mode Wire (gray wire)
• Arming switch (orange wire)
• Fuel pump power (blue wire)
• Fuel pump ground (black wire)
• Solenoid connectors (black plastic clips)
5.
After all connections have been removed, remove the Nitrous Control Module
from the backing plate. This can be done by using a flat head screwdriver
to pry the module off the plate
(Fig. 4)
. The module is held on by double
sided tape. Scrape off any remaining tape from the backing plate to ensure
that your new Adjustable Control Module mounts securely.
Fig 1
Fig 2
Fig 3
Fig 4
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 of 4 2004 Edelbrock CorporationBrochure #63-0131 Catalog #72230 Rev. 5/04 INSTALLATION 1. Install your new Adjustable Control Module onto thebacking plate in the same location as the Control Modulethat you just removed. Install the module so that theadjustment controls are located on the bott...
Page 3 of 4 2004 Edelbrock CorporationBrochure #63-0131 Catalog #72230 Rev. 5/04 WIRING DIAGRAM Wire System Origin Destination Color Red Battery Voltage Nitrous Module Harness Battery or Key activated circuit breaker Black Module Ground Nitrous Module Harness Ground to cylinder head bolt Green Tach ...
Page 4 of 4 2004 Edelbrock CorporationBrochure #63-0131 Catalog #72230 Rev. 5/04 ADJUSTING THE CONTROL MODULE The settings diagram located below is the same as the sticker that you previously installed. This diagram contains crucialinformation that will allow you to select the setting that you would...
