Edelbrock 65022 - Manual

©2007 Edelbrock Corporation
Catalog #65022 & 65023

Page 1 of 2

Brochure #63-0364

Rev. 8/07 - DA/mc

Edelbrock Header

For 2001-2008 GM 1500/2500 Series Pick-Up, Avalanche,

Suburban, Tahoe, & Yukon,

4.8L, 5.3L & 6.0L, V8 Auto,

2 & 4 Wheel Drive, Dual Catalytic without A.I.R. or E.G.R.

AND 2003-2008 Hummer II 6.0L V8 without A.I.R. or E.G.R.

Catalog #65022 (Ceramic) & 65023 (Ti-Tech)

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new Header. If you have any questions, please contact our

Technical

Hotline at : 1-800-416-8628

from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at

[email protected].

HEADERS:

These components are designed to improve the exhaust efficiency of the GM C.P.I. (Central Port Injection) V8 engine.

This

system does not require welding for installation

and retains all O.E.M. emissions equipment. These Edelbrock headers are

street legal in all 50 states.

Suggested Tools Needed for Installation.

This vehicle has metric fasteners:

❑

3/8" ratchet socket set with extensions and universal 13mm and 15mm swivel sockets

❑

Set of combination wrenches

❑

Jackstands, screwdrivers, pliers, crescent wrench, etc.

❑

Liquid penetrant, (GM #1052627) anti-seize compound (GM #5613695) or available equivalent.

SPECIAL NOTICE:

This Edelbrock part has received an Executive Order number (E.O.#) from the California Air Resources Board

(C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment certification, we have included a silver
fan shroud decal to help testing personnel verify the this part is a legal replacement on the vehicle for which it is cataloged. The
adhesive-backed decal should be affixed next to the existing emission and engine specifications decal. Do not cover any part of your
original emission decal.

WARNING:

The use of "Thermal Wrap" or any aftermarket coating process

will void the warranty

on your Edelbrock Headers.

Those products will cause excessive heat and moisture buildup resulting in corrosion and failure of the header.

NOTE: High temperature spark plug wires and boots are recommended to withstand heat from Headers.

INSTALLATION INSTRUCTIONS

DISASSEMBLY

1.

Disconnect negative battery cable.

2.

Unbolt exhaust pipes from manifolds.

RIGHT SIDE

1.

Disconnect and remove spark plug wires.

2.

Unbolt and remove dipstick tube.

3.

Unbolt and remove manifold from top.

4.

Install flange gasket and header from top.

Install

header bolts, lock washers, and thick flat washers
supplied.

Note:

Ensure proper alignment on slotted

holes of port flange and only snug bolts at this time.

5.

Re-install spark plug wires.

6.

Re-install dipstick tube.

7.

Some models may require the aluminum heat shield
under the A/C receiver dryer to be re-positioned,
adjusted or bent to gain some clearance between
header and heat shield.

LEFT SIDE

1.

Disconnect and remove spark plug wires.

2.

Unbolt and remove manifold.

3.

Install flange gasket and header from top. Install
header bolts, lock washers, and thick flat washers
supplied, ensure proper alignment and only snug
bolts at this time.

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.