Edelbrock 3835 - Manual

THROTTLE BODY ADAPTER

for 1994-1995 5.0L Mustangs

For Part Nos. 3821, 7123 and 7126 Manifolds

Catalog #3835

INSTALLATION INSTRUCTIONS

• Throttle Body Adapter: The throttle body adapter #3835 is

required to install any Performer 5.0 series intake manifold
on 1994-95 Mustangs. It must be used with Edelbrock or

stock throttle body. Performer series manifolds and adapter
#3835 are stock replacement parts and are 50-state street
legal for 1994-95 5.0L engines. Performer series manifolds

will not clear stock strut tower brace; Edelbrock Strut Tower
Brace #5225 must be used!

•

INSTALLATION:

1. Remove stock strut tower brace prior to installing intake

manifold. Install manifold base per provided installation
instructions.

2. Before installing manifold upper, drill out the threaded bolt

hole indicated in Figures 1 and 2 with a 11/32" drill. This

through hole will allow installation of a 5/16" bolt from the
rear into the throttle body adapter.

NOTE:

If manifold upper is already installed, this hole may be

drilled out on vehicle if you are careful not to let chips fall into
engine.

3. Install upper manifold.

NOTE:

Before installing throttle body adapter, remove both

throttle bracket studs from your stock manifold and install
them on the adapter. Note that they are metric (M8 x 1.25).

4. Install throttle body adapter and gasket using bolts supplied.

NOTE:

Use 1-1/4" 12-point bolt in upper rear position as

required for clearance (see Figure 2).

5. Install studs (supplied) in throttle body adapter.
6. Install throttle body per instructions supplied.
7. Install EGR valve and gasket on throttle body adapter.

8. EGR supply tube spacer PN 8025 is required for RPM 5.0

manifolds (PN 7126 & 7123) with most aftermarket or factory

headers. Edelbrock TES 6845 does

not

require a spacer.

9. Re-assemble all fittings, brackets, and other parts removed

during disassembly.

10. Original 11/32" vacuum hose must be extended using 3-1/4"

long hose and connector supplied.

11. Install Strut Tower Brace #5225 in place of stock strut tower

brace.

F i g u r e 1

– Throttle Body Adapter #3835 installed. Arrow

shows location of 11/32" through hole which must be
drilled in upper manifold.

Figure 2

– View of upper manifold

Drill through 11/32" diameter

Use 12-point head
5/16" bolt here

• K i t C o n t e n t s

1-

Throttle Body Adapter

1-

Throttle Body Gasket; adapter to manifold

1-

Throttle Body Gasket; adapter to Throttle Body

1-

EGR Gasket

4-

5/16" x 1-1/2" carb studs

4-

5/16" hex nuts

8-

5/16" AN flat washers

3-

1-1/2" hex head bolts

1-

1-1/4" 12-point head bolt

1-

3-1/4" length 11/32" diameter fuel/vacuum hose

1-

3/8 hose connector

1-

3/8 Pipe Plug

1-

1/8 Pipe Plug

Brochure #63-0163

© 2002 Edelbrock Corporation

Rev. 12/02

Please

study these instructions carefully before installing your new Throttle Body and EGR Plate. If you have any questions or problems,

do not hesitate to call our

Technical Hotline at: (800) 416-8628

from 7:00 am to 5:00 pm, Monday through Friday, Pacific Standard

Time or e-mail us at:

[email protected].