Edelbrock 3528 - Manual

Edelbrock 3528

Edelbrock 3528 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
Page: / 39

Table of Contents:

  • Page 2 – P R I M A RY K I T C O M P O N E N T S; PART NUMBERS
  • Page 3 – TOOLS AND EQUIPMENT; P R E L I M I N A R Y C H E C K L I S T; Check all threaded manifold holes.; HARDWARE AND PARTS RECOMMENDED; Use the following checklist for items needed.
  • Page 4 – EMISSION CONTROLS; DETERMINING HOOD CLEARANCE
  • Page 6 – FUEL SYSTEM; Tank Side; FUEL PUMP AND FILTER; primary fuel line
  • Page 7 – RUBBER RETURN LINE METHOD; BULKHEAD FITTING METHOD
  • Page 8 – HARD RETURN LINE METHOD
  • Page 9 – FUEL SYSTEM INSTALLATION; below
  • Page 11 – REMOVING THE STOCK CARBURETOR AND MANIFOLD; CAUTION: Do not remove manifold if engine is hot.; PORT SURFACE CLEANING
  • Page 12 – GASKET SURFACE PREPARATION
  • Page 13 – SENSORS; MANIFOLD ABSOLUTE PRESSURE SENSOR
  • Page 14 – THROTTLE POSITION SENSOR
  • Page 15 – SENSOR INSTALLATION
  • Page 16 – ENGINE HARNESS LA
  • Page 17 – MAIN SYSTEM HARNESS
  • Page 21 – INSTALLATION; CHASSIS HARNESS LAYOUT
  • Page 22 – ENGINE HARNESS
  • Page 23 – THROTTLE CABLE INSTALLATION
  • Page 25 – IGNITION SYSTEM; ELECTRONIC CONTROL UNIT / SYSTEM ECU
  • Page 26 – ADDING AFTERMARKET IGNITION; TYPICAL INSTALLATION; OTHER APPLICATIONS
  • Page 27 – CUSTOMER INTERFACE CONNECTOR; Pin Letter
  • Page 28 – INSTALLING THE SOFTWARE
  • Page 29 – SELECTING THE PROPER CALIBRATION; Application
  • Page 30 – Priming The Fuel Pump; B E F O R E
  • Page 31 – Timing Adjustment; ENTER to select
  • Page 33 – ELECTRONIC ENGINE MANAGEMENT; FUEL MODIFIER TABLE
  • Page 34 – PRO-FLO QUICK TUNING GUIDE; LEAN
  • Page 35 – OPTIONAL PC TUNING FEATURE
  • Page 36 – CALIBRATION MODULE DIAGRAM
  • Page 38 – COMPLETE PRO-FLO SYSTEM PARTS
  • Page 39 – SERVICE
Loading the manual

1

Pro-Flo EFI Installation Instructions

©2008 Edelbrock Corporation

Brochure No. 63-3527

Catalog #3527, #3528
Rev. 8/08 - AJ/mc

TABLE OF CONTENTS

Part #3527 and #3528

Introduction.................................................................................................................................................1

Components................................................................................................................................................2

Preliminaries ...............................................................................................................................................3

Fuel System ................................................................................................................................................6

Induction System ......................................................................................................................................10

Sensors ....................................................................................................................................................13

O2 Sensor Installation ...............................................................................................................................15

Main System Harness ...............................................................................................................................16

Ignition System .........................................................................................................................................25

Other Applications .................................................................................................................................... 26

Software Installation .................................................................................................................................28

Calibration Selection .................................................................................................................................29

System Start-Up........................................................................................................................................30

Electronic Engine Management .................................................................................................................33

Pro-Flo Quick Tuning Guide .......................................................................................................................34

Calibration Module Flowchart ....................................................................................................................36

Parts and Part Numbers ............................................................................................................................37

Service & Warranty ...................................................................................................................................39

INTRODUCTION

Thank you for selecting the Edelbrock Pro-Flo XT Fuel Injection System. This Multi-Point Fuel Injection System has been designed for 350 c.i.d.
small-block Chevrolet engines, and is designed to provide excellent performance, fuel economy, and maintenance-free operation. Installation of
the Edelbrock Pro-Flo XT Fuel Injection System involves modifications to the fuel system, ignition system, induction system, and possibly the
valve train. Although there are steps that must take place before others, the modifications do not necessarily have to be performed in a particular
order. Each modification is described in a separate section in this manual. Please study these instructions carefully before beginning installation
of any part of the Pro-Flo XT system.

If you have any questions, do not hesitate to call our

EFI Technical Hotline at (800) 416-8628, 7am-5pm PST, Monday-Friday

E-mail: [email protected]

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - P R I M A RY K I T C O M P O N E N T S; PART NUMBERS

2 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528Rev. 8/08 - AJ/mc P R I M A RY K I T C O M P O N E N T S ❑ Electronic Control Unit/System ECU ❑ Fuel filter ❑ Calibration Module ❑ Fuel rail assembly ❑ Distributor conversion kit ❑ Fuel press...

Page 3 - TOOLS AND EQUIPMENT; P R E L I M I N A R Y C H E C K L I S T; Check all threaded manifold holes.; HARDWARE AND PARTS RECOMMENDED; Use the following checklist for items needed.

3 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528Rev. 8/08 - AJ/mc TOOLS AND EQUIPMENT Use the following checklist for items needed. ❑ Box and open end wrenches ❑ Socket set ❑ Distributor wrench ❑ Pliers (channel locks and hose clamp) ❑ Scr...

Page 4 - EMISSION CONTROLS; DETERMINING HOOD CLEARANCE

4 Pro-Flo EFI Installation Instructions ©2008 Edelbrock Corporation Brochure No. 63-3527 Catalog #3527, #3528Rev. 8/08 - AJ/mc MANIFOLD & CARBURETOR HEIGHT VS. PRO-FLO XT HEIGHT 1. Lay a straightedge (such as a yardstick) across the top of the aircleaner from front to back.2. M e a s u r e f r o...

Other Edelbrock Models

All Edelbrock Other