Edelbrock 2930 - Manual

Catalog #2930
Rev. 12/05- RS/mc

Page 1 of 3

©2005 Edelbrock Corporation

Brochure #63-0464

TORKER AMC INTAKE MANIFOLD

For 1970 and Later AMC 343-401 C.I.D. Engines

Catalog #2930

INSTALLATION INSTRUCTIONS

PLEASE

study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and

procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this
installation, it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our

Technical

Hotline at: 1-800-416-8628

, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at

[email protected]

.

IMPORTANT NOTE: Proper installation is the responsibility of the installer.

Improper installation may result in poor performance and engine or vehicle damage.

PLEASE

complete and mail your warranty card. Be sure to write the model number of this product in the "Part #____" space.

THANK YOU

.

DESCRIPTION:

The Torker AMC intake manifold is designed for 1970 and later 343-360-390-401 C.I.D. AMC V8 engines. It is recommended for

street high performance, and race vehicles only. The Torker manifold is of single-plane design, utilizing modern air-flow technology. It is designed
to operate in the 2500-6500 rpm range, providing good low rpm response plus increased performance above 5000 rpm. Additional increases in
performance can be had when using this intake manifold with additional performance parts designed to operate within the listed rpm range.
Manifold will not accept factory Motorcraft spread-bore carburetors.
•

KIT CONTENTS:

❑

6

#8 x 3/8” Drive Screws

❑

1

Shoulder Stud Sleeve

❑

4

3/8-16 x 1-1/4” Hex Bolts

❑

1

10-32 x 1/2” Hex Cap Screw

❑

1

Shoulder Stud (Kickdown Stud)

❑

1

1/4 Star Washer

❑

1

Cotter Pin

•

EGR SYSTEMS:

Intake manifold will not accept stock EGR (Exhaust Gas Recirculation) equipment. EGR systems are used on most 1972 and

later model vehicles. Check local laws for requirements.

•

ACCESSORIES & INSTALLATION ITEMS:

Major recommendations are listed below. See our catalog for details.

To order a catalog, call

(800) FUN-TEAM

, or visit

www.edelbrock.com

.

•

CARBURETOR RECOMMENDATIONS:

NOTE:

See catalog for carburetor reference details.

CARBURETOR

REFERENCE

PARTS REQUIRED FOR INSTALLATION

Performer #1407 (750 cfm)

A, I, K, N, O

#8034 Throttle Bracket Extention (If originally 2bbl carb)

Performer #1412 (800 cfm)

A, I, K, N, O

#8034 Throttle Bracket Extention (If originally 2bbl carb)

Performer #1413 (800 cfm)

A, I, K, N

#8034 Throttle Bracket Extention (If originally 2bbl carb)

Thunder Series #1812 (800 cfm)

A, I, K, N

#8034 Throttle Bracket Extention (If originally 2bbl carb)

Thunder Series #1813 (800 cfm)

A, I, K, N

#8034 Throttle Bracket Extention (If originally 2bbl carb)

•

GASKETS:

Do not use competition-style intake gaskets for this street manifold. Due to material deterioration over time, internal leakage of

vacuum, oil, and coolant may occur.

INTAKE MANIFOLD

REFERENCE

RECOMMENDED GASKET

2930

(None)

Edelbrock #7213 Port: 1.130” x 2.210”, .060” Thickness

NOTE: To ensure maximum performance and a proper seal, Edelbrock gaskets which are

specifically designed and manufactured for use with Edelbrock parts must be used.