Page 2 - Edelbrock Corporation, 2700 California Street, Torrance, CA 90503; INTRODUCTION
©2009 Edelbrock CorporationCatalog #1580 Brochure #63-1580 Rev. 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 2 Edelbrock Corporation, 2700 California Street, Torrance, CA 90503 Toll-Free Tech Line: 1-800-416-8628 Office: 310-781-2...
Page 3 - result in poor performance and engine or vehicle damage.; IMPORTANT WARNINGS; stock condition before installing the supercharger.
©2009 Edelbrock CorporationCatalog #1580 Brochure #63-1580 Rev. 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 3 Due to the complexity of the Edelbrock E-Force Supercharging system, it is recommend that this system only beinstalled ...
Page 4 - INSTALLING A BOOST GAUGE OR PRESSURE TRANSDUCER; Voltage
©2009 Edelbrock CorporationCatalog #1580 Brochure #63-1580 Rev. 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 4 INSTALLING A BOOST GAUGE OR PRESSURE TRANSDUCER Your E-Force supercharger is equipped with two options for measuring bo...
Page 5 - Detach hose retaining clip, then remove these two pins.
©2009 Edelbrock CorporationCatalog #1580 Brochure #63-1580 Rev. 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 5 I. Hood Removal 1. Use a panel puller to pry off two of the push-pinsholding the hood insulator in place on the passeng...
Page 6 - Bolts; III. Removing Engine Components; ETC
©2009 Edelbrock CorporationCatalog #1580 Brochure #63-1580 Rev. 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 6 7. Use a 10mm socket with a 12” extension bar toremove the three bolts holding the battery tray in place,then use a pan...
Page 8 - Remove the fuel line lock clip and let it dangle.
©2009 Edelbrock CorporationCatalog #1580 Brochure #63-1580 Rev. 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 8 18. Remove the fuel line lock clip and let it dangle. 19. Use a 5/8” fuel line removal tool to disconnect thefuel suppl...
Page 12 - Use a 15mm socket to remove the hose bracket.
©2009 Edelbrock CorporationCatalog #1580 Brochure #63-1580 Rev. 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 12 42. Use large pliers or a clamp removal tool to detachboth upper radiator hoses from the water crossover. 43. Place sh...
Page 13 - Edelbrock 4.6L Ford Supercharger System; VI. Installing Intercooler Accessories
55. Hang the water pump on the passenger side outerbumper bolts while pushing the outlet hose onto the inletnipple of the heat exchanger. Secure the hose with aclamp, and the water pump bracket with two of the M8flange nuts supplied. 56. Install the long 3/4” hose onto the driver side barb ofthe hea...
Page 14 - ‘06 Model Year Example
©2009 Edelbrock CorporationCatalog #1580 Brochure #63-1580 Rev. 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 14 59. ‘05 applications should locate the red wire in pin 10,near the bottom of the connector. ‘06 applications shouldloc...
Page 15 - Recommended Tools; ETC Connector
70. Detach ETC connector from supplied ETC extensionharness and raise wedge lock. Insert the red wire withthe yellow stripe into Pin 1 of the new ETC connector byaligning the slot on the wire terminal with the tab in theconnector and pushing gently until it clicks into place,then insert the blue wir...
Page 16 - TPS Connector
80. Locate the electrical connector on the main harnesspreviously occupied by the alternator control wiringharness. Attach the round alternator connector on thesupplied TPS/Alternator harness into this connector androute the harness around the back of the engine bay, thenforward along the driver sid...
Page 17 - VIII. Cooling System Modifications; TMAP Connector
VIII. Cooling System Modifications 89. Route the molded hose under the fuse box and ontothe inlet at the top of the water pump. Secure it with aclamp. 90. Remove the two inner passenger side strut towernuts and hang the recovery tank bracket from theexposed bolts. Do not reinstall strut nuts at this...
Page 20 - Early Model Plug
XI. Installing the Supercharger 112. Install the Edelbrock supplied heater hose on thefirewall connector, and lay it to the side for now. 113. Remove the supercharger assembly from its packingcontainer and install the o-ring seals, removed from thestock manifold on early applications and supplied in...
Page 22 - Plug wiring harness extension into TMAP sensor.; XII. Modifying Stock Components
126. Connect the EVAP hose to the hard line at the frontof the manifold. 127. Reconnect the fuel pressure sensor to the mainwiring harness. Be sure to use the connector that doesnot have a red locking tab, the connector with a redlocking tab is for the TPS. 128. Plug wiring harness extension into TM...
Page 23 - Use a 10mm socket to reinstall the tensioner.
134. Use a flat head screwdriver to pop off the bearingcover on the alternator pulley. ‘05-’08 applications shoulduse the supplied tool with an impact wrench to removethe stock pulley. ‘09 and later applications should use a24mm allen tool with an impact wrench. 135. Install the new alternator pulle...
Page 24 - XIII. Installing the Throttle Body; Rotating the TPS when removing or
140. Route the supplied serpentine belt according to thediagram provided below by using a 1/2” breaker bar totwist the belt tensioner enough to allow the belt to slideinto place. XIII. Installing the Throttle Body 141. Use 8mm and 10mm sockets to unbolt the OEMthrottle body from the stock intake man...
Page 25 - Carefully remove the motor housing cap.
147. Reinstall the motor housing cap by lining up the tabsand applying light pressure. 148. Reuse the stock bolts to install the TPS on the newthrottle body by lining up the locating tab and pushing itstraight on. Be careful to avoid rotating the TPS duringinstallation. 149. Verify correct installat...
Page 26 - Install the new high flow air filter in the airbox.
152. Install the new high flow air filter in the airbox. 153. Use a T20 Torx driver to install the new MAF sensorin the air cover outlet tube, torque the two screws thatretain it to 18 in/lbs., then reinstall the cover. 154. Install the throttle body elbow onto the throttle bodyand secure it with th...
Page 28 - XV. Flashing the ECU; Turn the ignition key to the ‘ON’ position.
174. Verify that water is flowing briskly through therecovery tank, then install the cap. 175. Have an assistant support the hood while youtighten the four bolts that secure it to its hinges. Becareful to verify that it is properly aligned and that thesupercharger has nothing on top of it before you...
Page 29 - Read the disclaimer and press select.
©2009 Edelbrock CorporationCatalog #1580 Brochure #63-1580 Rev. 2/09 - AJ/mc Edelbrock 4.6L Ford Supercharger System for 2005 and later Mustang GTs Installation Instructions Page 29 179. Read the discalimer carefully, then choose ‘Agree’and press select. 180. Use the arrow buttons to select your tra...
