EcoFlow ZMH100-B-US-V20 - User Manual

2 5. During the manual control, do not overextend it and maintain balance at all times. Secure footing when the mower is moving on slopes. Always wear long trousers and work shoes. 6. Do not run while operating the mower or its peripherals. 7. In case of abnormal vibrations, please turn off the mowe...

3 Symbols and Decals WARNING-Read instruction manual before operating the machine. WARNING-Do not ride on the machine. WARNING - Remove the disabling device before working on or lifting the machine (The disabling device means battery pack) *Make sure the battery is removed before working on or lifti...

5 Product Overview Front Fig. 1 Side view of EcoFlow Blade Front Rear Rear 1. Headlight 2. Front wheel (omni-wheel) 3. Battery compartment cover 4. Back wheel (drive wheel) 5. Tail light 6. Power button 7. Start button 8. Recharge button 9. STOP button 10. Port for Lawn Sweeper Kit EcoFlow Blade ❶ ❾...

7 Charging Station & GNSS Antenna GNSS antenna kit Charging station 1. LED indicator 2. Charging pad 3. Holes for nails 4. Extension cable connector 5. Power cable connector ❶ ❶ ❸ ❹ ❷ ❷ ❸ ❹ ❺ Fig. 3 GNSS Antenna kit Please be noted that Tube 1 has two different ends 1. Fork 2. Antenna tube 1 3. ...

8 Select Locations For a better performance, the following pink areas are not recommended for GNSS antenna and charging station. 1. Do not put the antenna or charging station between walls. < 4m/13 in 2. Do not keep the antenna or charging station under trees. Fig. 5 Unrecommended areas

10 Installation There are a couple of ways to install the antenna, here are two most common options for your reference. Option 1 1. Install tube 1 onto the fork and then install tube 2 onto tube 1. Install the GNSS antenna B2 B1 2. Slide the extension cable through the tubes.

14 1. Connect the extension cable to the charging station. Install the charging station B1 A1 B1 B1 B1 B1 A1 A1 A2 B1 A1 A1 2. Connect the power cable to the charging station. Secure the cable connectors tightly to prevent the cable from being loose during use.

16 1. Remove the sticker attached to the front of the mower. Control, monitor, and customize your EcoFLow Blade from afar with the EcoFlow App. Download at: https://download.ecoflow.com/app Privacy policy By using EcoFlow Products, Applications, and Services, you consent to the EcoFlow Term of Use a...

19 1. Take off the protective covers. 1. Please be aware of sharp points of the fork, do not get yourself hurt. 2. Do not put anything on the antenna. Location for the antenna kit Location for charging station 2. Insert the antenna into the ground. After you have fixed the position of the antenna, n...

22 Set up the working area Before setup Clean your lawn Remove all the obstacles inside the working area, including toys, wires, stones, etc. Make sure that kids and pets are not near the mower. < 76mm/3 in

24 Working area 1. On "Guide to EcoFlow Blade" page, select "Create mower work map". 2. Follow the instructions and proceed to select "Start mapping". 3. Select "Mapping work area".

27 1. We suggest that you move the mower near the area where you want to set up the "no- go zone", then tap the "start" button and tap "finish" button to end the process. 2. Please keep the restricted zones inside of the working area, otherwise, the app will remind you that y...

28 Path 1. Select "Mapping channel" on the guide page. 2. Draw a path between two or more working areas by using the direction keys. Make sure you have created more than two working areas (see steps in working area ). LED Indication Light Color Status Meaning Head light Blue Dark blue as the...

30 Settings Start/Pause After "Guide to EcoFlow Blade", you can choose "Start working". Recharge/Return the charging station 1. Tap "Start", the mower will start mowing. 2. Tap "Pause" to pause the mower, and then tap again to resume the work. Option 1 While the mower...

31 Device sharing If you need to share this mower with someone else, please follow the steps below: 1. Tap the icon in the lower right. 2. Select "Device sharing". 1. If the mower is bonded with an account, then the new operators cannot connect to the mower unless the original account shares...

33 3. Slide your finger to adjust the mowing height. Firmware upgrade Online upgrade 1. Tap the icon in the lower right and then tap "Firmware". 2. Select "Upgrade", and wait for the process to complete.

35 Cleaning Transportation Hold the handle when you need to lift or move the mower. Maintenance Please do not use high-pressure water to clean the mower in case of component damage 1. Ensure that the mower is powered off, and remove the battery before cleaning. 2. Clean the mower with a damp clean c...

40 Specifications Basic information Name EcoFlow Blade Model WR303 Size of the mower approx. 669*452*312 mm (26 × 18 × 12 in.) Size of the charging station approx. 715*501*205 mm (28 × 20 × 8 in.) Weight of the mower 12.3 kg (lbs) Weight with package 27.2 kg (lbs) Material Plastic and aluminium allo...

42 FAQ 1. The robotic lawn mower cannot return to the charging station automatically. Why? It may not return to the charging station in the following cases: 1. The satellite signal is weak due to walls, trees or other obstacles within the range of 2m (6.56ft ) around the antenna. Solution: Move the ...