Page 3 - Debris Shield Decal; Hot Surface Decal; WARNING; Shaft Decal - Spanish
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 3 This symbol accompanied by the words WARNING andDANGER calls attention to an act or condition that canlead to serious personal injury to operator and bystand-ers. The circle with the slash symbol means whatever isshown within the circle is proh...
Page 4 - Shaft Decal; • This unit can be dangerous and cause serious injury if improperly; • Beware of KICKOUT (blade thrust) when using blades. Special; IMPROPERLY SHARPENED BLADES.; INTERNATIONAL
4 Shaft Decal WARNING DANGER • This unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders,read and understand the Operator's and Safety manuals. • Blindness can occur from objects that are thrown or ricocheted even with shield in...
Page 6 - Repetitive Stress Injuries; EQUIPMENT
6 Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers,hands, arms, and shoulders may cause soreness, swelling, numbness,weakness, and extreme pain in those areas. Certain repetitive handactivities may put you at a high risk for developing a Repetitive Stre...
Page 7 - and Safety Manual for instructions on safe operation.; MISSION; EPA Phase 2; PRODUCT EMISSION DURABILITY
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 7 SAFE OPERATION WARNING DANGER Do not operate this product indoors or in inadequately ventilatedareas. Engine exhaust contains poisonous emissions and can causeserious injury or death. Read the Manuals• Provide all operators of this equipment wi...
Page 8 - - 2 mm x 25 mm Cotter pins
8 D ESCRIPTION Your new Echo product has been factory pre-assembled for your convenience. Due to packaging restrictions, shieldinstallation and other final assembly may be necessary. Check the contents carefully, and notify your retailer or ECHO Dealer immediately if any parts are missing or damaged...
Page 10 - position to open choke.; MODEL SRM-210U PART DESCRIPTIONS
10 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System, and Recoil Starter. 2. RIGHT HAND GRIP 3. THROTTLE TRIGGER LOCKOUT - This lever must be held during acceleration. Operation of the throttle trigger isprevented unless throttle trigger lockout lever is engaged. 4. STOP SWIT...
Page 11 - PECIFICATIONS; * Install and use U-Handle when operating any model with blade.; Premium Universal 2-Stroke Oil
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 11 S PECIFICATIONS * Install and use U-Handle when operating any model with blade. MODEL --------------------------------------------------------------- SRM-210U Length ----------------------------------------------------------------- 1770 mm (69...
Page 12 - Tools Required: Screwdriver, Locking Tool; Tools Required: Locking Tool, 17x19 mm Scrench
12 A SSEMBLY PLASTIC SHIELD INSTALLATION Tools Required: Screwdriver, Locking Tool Parts Required: Plastic Debris Shield, Shield Plate, three (3) 5 x 16 mm screws. WARNING DANGER The plastic shield is for use with the Nylon Line Head only. InstallMetal Shield when using plastic or metal blades, or s...
Page 13 - Install Metal Shield; Locking Tool; BLADE
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 13 C B A D G NOTEModel SRM-210U includes U-Handle, 8-tooth blade, and neces-sary blade conversion parts. Blades must be selected for type ofcutting being performed. See page 16, "Blade Selection." Install Metal Shield Tools Required: 8 x ...
Page 14 - Install Blade; HANDLE; mm flat washer
14 Install Blade Tools Required: Locking Tool, Scrench. Parts Required: Upper Plate w/ 20 mm pilot, Lower Plate, 10 mm Nut w/ L.H. threads, 2 x 25 mm Cotter Pin, Blade. 1. Install upper plate (D) on splined PTO shaft, pilot side down. Bladeinstallation requires Upper Plate (D) with 20 mm pilot. 2. I...
Page 18 - RE; Fuel Requirements; Gasoline - Use 89 Octane; Handling Fuel
18 IMPORTANTSpilled fuel is a leading cause ofhydrocarbon emissions. Some statesmay require the use of automatic fuelshut-off containers to reduce fuelspillage. Contact your ECHO dealer forordering information. After Refueling • Wipe any spilled fuel from the unit.• Move at least 3 m (10 ft.) from r...
Page 19 - Choke Lever
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 19 O PERATION STARTING COLD ENGINE WARNING DANGER The cutting attachment should not rotate at idle. If attachmentrotates, readjust carburetor according to "Carburetor Adjustment"instructions in this manual or see your ECHO Dealer, otherwi...
Page 20 - STOPPING
20 STARTING WARM ENGINE WARNING DANGER The cutting attachment should not rotate at idle. If attachmentrotates, readjust carburetor according to "Carburetor Adjustment"instructions in this manual or see your ECHO Dealer, otherwiseserious personal injury may result. 1. Stop SwitchMove stop swi...
Page 21 - Easy to do. Most required tools come with unit.; ECHO offers REPOWER
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 2 1 MAINTENANCE INTERVALS / T N E N O P M O C M E T S Y S E C N A N E T N I A M E R U D E C O R P D ' Q E R L L I K S L E V E L R O Y L I A D E R O F E B E S U Y R E V E L E U F E R 3 S H T N O M 0 9 R O S R U O H 6 S H T N O M 0 7 2 R O S R U O ...
Page 22 - still fits the cavity in the air cleaner cover.; FUEL; Use the “fuel line hook” to pull the fuel line and filter from the tank.
22 AIR FILTER Level 1. Tools required: 25-50 mm (1 or 2 in.) medium bristle paint brush. Parts required: 90030 REPOWER TM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from enteringthe carburetor throat when the air filter is removed. Brush accumu-lated dirt fro...
Page 23 - Parts Required: REPOWER; Remove spark plug and check for wear or fouling.; COOLING; • Dust and grass build-up on the outside of the cylinder. This build up
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 23 SPARK PLUG Level 2. Tools Required: Scrench (combination socket wrench & screw driver) Feeler gauge, preferably a wire gauge. Brush. Parts Required: REPOWER TM Tune-Up Kit P/N 90074 1. Remove spark plug and check for wear or fouling. 2. Cl...
Page 24 - EXHAUST; Spark Arrestor Screen; Tools Required: Cross Head Screwdriver, Soft metal brush, Wooden
24 4. Use the wooden stick or brush to remove dirt from the cylinder fins. 5. Install engine cover properly, placing fuel vent tube into enginecover and deflector shield tabs (A) into slots in engine cover. 6. Secure engine cover with three (3) screws. 7. Install top guard, and secure with one (1) s...
Page 25 - High Altitude Adjustment
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 25 A CARBURETOR ADJUSTMENT NOTENew engines must be operated for a minimum of two tanks of fuelbefore carburetor adjustments can be made. During the break-inperiod your engine performance will increase and exhaust emissionswill stabilize. Idle spe...
Page 26 - LUBRICATION; LUBE; Gear Housing; Clean all loose debris from gear box.; Drive Shaft; Install the gear housing and shield assembly.
26 A LUBRICATION Level 1. Tools Required: 8 mm Open-end Wrench, Screwdriver, Clean Rag. Parts Required: ECHO ® LUBE TM 8 oz. (P/N 91014) or Lithium Base Grease. Gear Housing 1. Clean all loose debris from gear box. 2. Remove plug (A) and check level of grease. 3. Add grease if necessary. DO NOT over...
Page 27 - Shut engine off. Lay unit on the ground with head assembly up.
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 27 NYLON LINE REPLACEMENT Level 1. Parts Required: ECHO 0.095" Nylon Trimmer Line 6 m (20 ft.) long. 1. Shut engine off. Lay unit on the ground with head assembly up. 2. Hold drum (A) and turn spool (B) CW (clockwise) until it stops.Pull spoo...
Page 28 - Pull both lines out and trim to cut-off knife length.; SHARPENING
28 8. Hold drum (A) firmly and turn spool (B) CCW (counterclockwise)until it stops. DO NOT push in on spool when turning. 9. Pull both lines out and trim to cut-off knife length. SHARPENING METAL BLADES Three styles of metal blades are approved for use on the ECHO BrushCutter. The 8-tooth blade can ...
Page 29 - ROUBLESHOOTING
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 29 T R A H C G N I T O O H S E L B U O R T M E L B O R P E N I G N E m e l b o r P k c e h C s u t a t S e s u a C y d e m e R e n i g n E - s k n a r c / d r a h s t r a t s t ' n s e o d t r a t s r o t e r u b r a c t a l e u F t a l e u f o N...
Page 30 - TORAGE; Tighten all the screws and nuts.
30 S TORAGE WARNING DANGER During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clearof flammable debris during transportation or when storing, otherwise serious property damage or personal injurymay result. Long Term Storage (over 30 days) Do ...
Page 31 - NOTES
G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 31 NOTES
Page 32 - CALL; Available Parts Catalog Parts Lists
ECHO, INCORPORATED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047-1564 www.echo-usa.com DEALER? CALL 1-800-432-ECHO OR www.echo-usa.com CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 MON - FRI C.S.T. S ERVICING I NFORMATION PARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies foryour EC...
