ECHO SRM-210U - Manuals

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 7 SAFE OPERATION WARNING DANGER Do not operate this product indoors or in inadequately ventilatedareas. Engine exhaust contains poisonous emissions and can causeserious injury or death. Read the Manuals• Provide all operators of this equipment wi...

8 D ESCRIPTION Your new Echo product has been factory pre-assembled for your convenience. Due to packaging restrictions, shieldinstallation and other final assembly may be necessary. Check the contents carefully, and notify your retailer or ECHO Dealer immediately if any parts are missing or damaged...

10 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System, and Recoil Starter. 2. RIGHT HAND GRIP 3. THROTTLE TRIGGER LOCKOUT - This lever must be held during acceleration. Operation of the throttle trigger isprevented unless throttle trigger lockout lever is engaged. 4. STOP SWIT...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 11 S PECIFICATIONS * Install and use U-Handle when operating any model with blade. MODEL --------------------------------------------------------------- SRM-210U Length ----------------------------------------------------------------- 1770 mm (69...

12 A SSEMBLY PLASTIC SHIELD INSTALLATION Tools Required: Screwdriver, Locking Tool Parts Required: Plastic Debris Shield, Shield Plate, three (3) 5 x 16 mm screws. WARNING DANGER The plastic shield is for use with the Nylon Line Head only. InstallMetal Shield when using plastic or metal blades, or s...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 13 C B A D G NOTEModel SRM-210U includes U-Handle, 8-tooth blade, and neces-sary blade conversion parts. Blades must be selected for type ofcutting being performed. See page 16, "Blade Selection." Install Metal Shield Tools Required: 8 x ...

14 Install Blade Tools Required: Locking Tool, Scrench. Parts Required: Upper Plate w/ 20 mm pilot, Lower Plate, 10 mm Nut w/ L.H. threads, 2 x 25 mm Cotter Pin, Blade. 1. Install upper plate (D) on splined PTO shaft, pilot side down. Bladeinstallation requires Upper Plate (D) with 20 mm pilot. 2. I...

18 IMPORTANTSpilled fuel is a leading cause ofhydrocarbon emissions. Some statesmay require the use of automatic fuelshut-off containers to reduce fuelspillage. Contact your ECHO dealer forordering information. After Refueling • Wipe any spilled fuel from the unit.• Move at least 3 m (10 ft.) from r...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 19 O PERATION STARTING COLD ENGINE WARNING DANGER The cutting attachment should not rotate at idle. If attachmentrotates, readjust carburetor according to "Carburetor Adjustment"instructions in this manual or see your ECHO Dealer, otherwi...

20 STARTING WARM ENGINE WARNING DANGER The cutting attachment should not rotate at idle. If attachmentrotates, readjust carburetor according to "Carburetor Adjustment"instructions in this manual or see your ECHO Dealer, otherwiseserious personal injury may result. 1. Stop SwitchMove stop swi...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 2 1 MAINTENANCE INTERVALS / T N E N O P M O C M E T S Y S E C N A N E T N I A M E R U D E C O R P D ' Q E R L L I K S L E V E L R O Y L I A D E R O F E B E S U Y R E V E L E U F E R 3 S H T N O M 0 9 R O S R U O H 6 S H T N O M 0 7 2 R O S R U O ...

22 AIR FILTER Level 1. Tools required: 25-50 mm (1 or 2 in.) medium bristle paint brush. Parts required: 90030 REPOWER TM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from enteringthe carburetor throat when the air filter is removed. Brush accumu-lated dirt fro...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 23 SPARK PLUG Level 2. Tools Required: Scrench (combination socket wrench & screw driver) Feeler gauge, preferably a wire gauge. Brush. Parts Required: REPOWER TM Tune-Up Kit P/N 90074 1. Remove spark plug and check for wear or fouling. 2. Cl...

24 4. Use the wooden stick or brush to remove dirt from the cylinder fins. 5. Install engine cover properly, placing fuel vent tube into enginecover and deflector shield tabs (A) into slots in engine cover. 6. Secure engine cover with three (3) screws. 7. Install top guard, and secure with one (1) s...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 25 A CARBURETOR ADJUSTMENT NOTENew engines must be operated for a minimum of two tanks of fuelbefore carburetor adjustments can be made. During the break-inperiod your engine performance will increase and exhaust emissionswill stabilize. Idle spe...

26 A LUBRICATION Level 1. Tools Required: 8 mm Open-end Wrench, Screwdriver, Clean Rag. Parts Required: ECHO ® LUBE TM 8 oz. (P/N 91014) or Lithium Base Grease. Gear Housing 1. Clean all loose debris from gear box. 2. Remove plug (A) and check level of grease. 3. Add grease if necessary. DO NOT over...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 27 NYLON LINE REPLACEMENT Level 1. Parts Required: ECHO 0.095" Nylon Trimmer Line 6 m (20 ft.) long. 1. Shut engine off. Lay unit on the ground with head assembly up. 2. Hold drum (A) and turn spool (B) CW (clockwise) until it stops.Pull spoo...

28 8. Hold drum (A) firmly and turn spool (B) CCW (counterclockwise)until it stops. DO NOT push in on spool when turning. 9. Pull both lines out and trim to cut-off knife length. SHARPENING METAL BLADES Three styles of metal blades are approved for use on the ECHO BrushCutter. The 8-tooth blade can ...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 29 T R A H C G N I T O O H S E L B U O R T M E L B O R P E N I G N E m e l b o r P k c e h C s u t a t S e s u a C y d e m e R e n i g n E - s k n a r c / d r a h s t r a t s t ' n s e o d t r a t s r o t e r u b r a c t a l e u F t a l e u f o N...

30 S TORAGE WARNING DANGER During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clearof flammable debris during transportation or when storing, otherwise serious property damage or personal injurymay result. Long Term Storage (over 30 days) Do ...

G RASS T RIMMER /B RUSH C UTTER O PERATOR ' S M ANUAL 31 NOTES

ECHO, INCORPORATED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047-1564 www.echo-usa.com DEALER? CALL 1-800-432-ECHO OR www.echo-usa.com CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 MON - FRI C.S.T. S ERVICING I NFORMATION PARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies foryour EC...