Dynex dx-drtvm102 - Manual
Dynex dx-drtvm102 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Safety information and specifications; IMPORTANT SAFETY; Do not use this product for any; Maximum weight
- Page 3 – TVs the wall mount fits; rt
- Page 4 – Tools needed; You will need the following tools to assemble your new wall mount:; OR
- Page 5 – Package contents; TV Hardware Bag; Not all hardware will be used.; Concrete anchor; Label; M6 washer
- Page 6 – The center of your TV will match the center of the wall plate (; measurement is; Measuring tape
- Page 7 – Option 1: Installing on a wood stud wall; Align the wall plate with the pilot holes, then place the washers (; D E
- Page 8 – Option 2: Installing on a solid concrete or concrete block wall*; Mount the wall plate directly onto the concrete surface.; Insert concrete wall anchors (
- Page 9 – Flat back; Obstructed back; assembling the wall mount.; Irregularly-shaped back; spacers when assembling the wall mount.; Remove the TV brackets.
- Page 10 – Step 4: Select screws and spacers; Select one of the following types of washers:; To avoid potential personal injuries and
- Page 11 – Step 5: Adjusting the tilt; The tilt on the left TV bracket (; Use a Phillips screwdriver to remove the two tilt screws (; and; Do not over tighten the screws.; Option 2: Mount not tilted; Tilt bracket
- Page 12 – Step 6 - Option 1: Installing on a TV with a flat back; Align the holes you noted on the left TV bracket (; Screws
- Page 13 – Option 2: Installing on a TV with an irregular or obstructed back; or
- Page 14 – Step 7: Mount the TV on the wall plate; Lower the TV onto the wall plate (
- Page 15 – Removing the TV from the wall plate; Unlatched
Safety information and specifications ............... 2
TVs the wall mount fits ............................................ 3
Tools needed ............................................................... 4
Parts................................................................................ 4
Hardware ...................................................................... 5
Assembly instructions ............................................. 6
For wood-stud, solid concrete, or
concrete block installation
DX-DRTVM102
Medium Low Profile Wall Mount with Optional 5° Tilt
A S S E M B LY G U I D E
Before using your new product, please read these instructions to prevent any damage.
DX-DRTVM102_12-1058_MAN_V3_ENG.fm Page 1 Wednesday, April 10, 2013 3:14 PM
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Need help? Call 800-305-2204 Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS CAUTION: Do not use this product for any purpose not explicitly specified by Dynex.Improper installation may cause property damage or personal injury. If you do not understand...
3 Need help? Call 800-305-2204 TVs the wall mount fits The wall mount fits TVs with M4, M5, or M6 screw holes that are the following distances apart: 13.8" (35 cm) maximum horizontal distance 9 .1" (23 cm) v e rt ical distanc e DX-DRTVM102_12-1058_MAN_V3_ENG.fm Page 3 Wednesday, April 10, 20...
4 Need help? Call 800-305-2204 Parts Tools needed You will need the following tools to assemble your new wall mount: Edge-to-edge stud finder Pencil Tape measure Hammer Level Phillips screwdriver Socket wrench with 1/2" (13 mm) socket or adjustable wrench Drill 7/32" (5.5 mm) wood drill bit ...
