Dymo M1011 - Manual

Dymo M1011

Dymo M1011 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
Page: / 16

Table of Contents:

  • Page 3 – About Your New Label Maker; Metal tapes are available as follows:
  • Page 4 – Loading the Tape; The DYMO M1011 is set to emboss non-adhesive aluminium tape.; To load the tape roll; to ensure the tape is visible at the tape exit.
  • Page 5 – Cutting the Label; To cut the label; Before cutting the tape, make sure the end of the tape extends
  • Page 6 – Embossing the Label; Avoid turning the embossing wheel at the same time you are; To emboss a label; Turn the character selection wheel (G) until the desired letter is; To add space between words
  • Page 7 – Embossing on Stainless Steel Label; To adjust for stainless steel label
  • Page 8 – Retracting the Label; To retract the label
  • Page 9 – Removing the Label; To remove the label; Use caution when removing stainless steel tape that may have
  • Page 10 – Centering the Text on the Label; To center the text on a long label; To center the text on a short label; on the
  • Page 11 – Applying Self-Adhesive Labels; To apply self-adhesive tape
  • Page 12 – Punching Holes in Non-Adhesive Labels; To punch a hole; Insert one end of the cut label into the cable tie slot (K) with the
  • Page 13 – Changing the Wheel; You can replace the character wheel with a Reverse Image Wheel.; To change the wheel
  • Page 14 – Hints for Trouble Free Operation
  • Page 15 – Warranty Registration; USA; and; Canada; : For repairs or replacement, please contact your local
Loading the manual

Rhino

M1011

www.dymo.com

User Guide
Guide D’Utilisation
Bedienungsanleitung
Guida per l’utente
Guía del usuario
Guia do Usuário

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - About Your New Label Maker; Metal tapes are available as follows:

3 About Your New Label Maker With your new DYMO M1011 label maker, you can create metal labels. The label maker uses DYMO 12 mm (1/2") tape. Metal tapes are available as follows: • Aluminium with adhesive (35800)• Aluminium without adhesive (31000)• Stainless Steel (32500) You can also use a Rev...

Page 4 - Loading the Tape; The DYMO M1011 is set to emboss non-adhesive aluminium tape.; To load the tape roll; to ensure the tape is visible at the tape exit.

4 Loading the Tape The DYMO M1011 is set to emboss non-adhesive aluminium tape. To load the tape roll 1. Hold the label maker in your left hand.2. Open tape cassette door (A).3. Insert roll of tape allowing the end to extend about 5 cm (2") through the label slot. 4. Close the tape cassette door...

Page 5 - Cutting the Label; To cut the label; Before cutting the tape, make sure the end of the tape extends

5 Cutting the Label To cut the label 1. Squeeze the embossing handle half-way, several times until the tape extends from the front of the tape exit (M) by at least 2,5 cm (1"). Before cutting the tape, make sure the end of the tape extends beyond the edge of the cutting assembly so you can easil...

Other Dymo Models

All Dymo Other