Dodge 2010 Charger - Manual

WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident orbodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If youdo not read this entire manual, you may miss importantinforma...

VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle couldseriously affect its roadworthiness and safety andmay lead to an accident resulting in serious injury ordeath. 1 INTRODUCTION 7

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 12 ▫ Key FOB . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ Removing Key FOB From Ignition . . . . . . . . . 14 ▫ Key-...

A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This systemconsists of a Key Fob with Remote Keyless Entry (RKE)transmitter and a Wireless Ignition Node (WIN) withintegral ignition switch. You can insert the Key Fob intothe ignition switch with either side up. Wireless Ignition N...

Key Fob The Key Fob operates the ignition switch. It also containsthe Remote Keyless Entry (RKE) transmitter and anemergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicleshould the battery in the vehicle or the Key Fob go dead.The emergency key is ...

Removing Key Fob From Ignition Place the shift lever in PARK. Turn the key to the LOCKposition and then remove the Key Fob. NOTE: • For vehicles not equipped with the Electronic VehicleInformation Center (EVIC), the power windowswitches, radio, power sunroof (if equipped), andpower outlets will rema...

Key-In-Ignition Reminder Opening the driver’s door when the Key Fob is in theignition and the ignition switch position is OFF or ACC,sounds a signal to remind you to remove the Key Fob. NOTE: The Key-In-Ignition reminder only sounds when the Key Fob is placed in the LOCK or ACC ignitionposition. SEN...

CAUTION! The Sentry Key 威 Immobilizer system is not compat- ible with some after-market remote starting systems.Use of these systems may result in vehicle startingproblems and loss of security protection. All of the Key Fobs provided with your new vehicle havebeen programmed to the vehicle electroni...

NOTE: When having the Sentry Key 威 Immobilizer System serviced, bring all vehicle Key Fobs with you tothe authorized dealer. Customer Key Programming Programming Key Fobs or RKE transmitters may beperformed at an authorized dealer. General Information The Sentry Key 威 system complies with FCC rules ...

vehicle and open a door, the alarm will sound. If thisoccurs, disarm the Vehicle Security Alarm. If the Vehicle Security Alarm is armed and the batterybecomes disconnected the Vehicle Security Alarm willremain armed when the battery is reconnected. Theexterior lights will flash, the horn will sound,...

REMOTE KEYLESS ENTRY (RKE) The RKE system allows you to lock or unlock the doors,open the trunk, or activate the Panic Alarm from dis-tances up to approximately 66 ft (20 m) using a hand-heldKey Fob with RKE transmitter. The RKE transmitter doesnot need to be pointed at the vehicle to activate thesy...

Flash Lights with Remote Key Lock This feature will cause the turn signal lights to flash whenthe doors are locked or unlocked with the RKE transmit-ter. This feature can be turned on or turned off. To changethe current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “El...

NOTE: • Do not touch the battery terminals that are on the backhousing or the printed circuit board. 1. Battery access is through a door located on the rear ofthe RKE transmitter. Insert a small, flat blade screwdriverinto the slot and gently pry open the access door. 2. Remove and replace the batte...

3. Reposition the access door panel over the batteryopening and snap into place. General Information This device complies with Part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions: • This device may not cause harmful interference. • This device must...

NOTE: • The park lamps will turn on and remain on duringRemote Start mode. • For security, power window and power sunroof op-eration (if equipped) are disabled when the vehicle isin the Remote Start mode. • The engine can be started two consecutive times (two15-minute cycles) with the RKE transmitte...

DOOR LOCKS Manual Door Locks To lock each door, push the door lock plunger on eachdoor trim panel downward. To unlock each door, pull thedoor lock plunger on each door trim panel upward. If the door lock plunger is down when you shut the door,the door will lock. Therefore, make sure the key is notin...

Power Door Locks A power door lock switch is on each front door trimpanel. Use this switch to lock or unlock the doors. If you press the power door lock switch while the KeyFob is in the ignition, and any front door is open, thepower locks will not operate. This prevents you from accidentally lockin...

Automatic Door Locks Programming The Automatic Door Locks feature can be enabled ordisabled as follows: • For vehicles equipped with the Electronic VehicleInformation Center (EVIC), refer to “Electronic VehicleInformation Center (EVIC) — If Equipped/PersonalSettings (Customer-Programmable Features)”...

4. The driver door is opened. 5. The doors were not previously unlocked. 6. The vehicle speed is 0 mph (0 km/h). Automatic Unlock Doors on Exit Programming The Automatic Unlock Doors On Exit feature can beenabled or disabled as follows: • For vehicles equipped with the EVIC, refer to “Elec-tronic Ve...

Child Protection Door Lock To provide a safer environment for small children ridingin the rear seats, the rear doors are equipped with a ChildProtection Door Lock system. To Engage the Child Protection Door Lock System 1. Open the rear door. 2. Insert the tip of the emergency key (or similar object)...

3. Repeat Steps 1 and 2 for the opposite rear door. NOTE: After disengaging the Child Protection Door Lock system, always test the door from the inside tomake certain it is in the desired position. WINDOWS Power Windows The window controls on the driver’s door control all thedoor windows. There are ...

Window Lockout Switch The window lockout switch on the driver’s door trimpanel allows you to disable the window controls on thepassenger doors. To disable the window controls, pressand release the window lockout button (setting it in theDOWN position). To enable the window controls, pressand release...

1. Pull the window switch up to close window com-pletely and continue to hold the switch up for anadditional two seconds after the window is closed. Wind Buffeting Wind buffeting can be described as the perception ofpressure on the ears or a helicopter-type sound in theears. Your vehicle may exhibit...

With the ignition switch in the OFF position or the keyremoved from the ignition switch, the Trunk Open sym-bol will display until the trunk is closed. TRUNK SAFETY WARNING WARNING! Do not allow children to have access to the trunk,either by climbing into the trunk from outside, orthrough the inside...

OCCUPANT RESTRAINTS Some of the most important safety features in yourvehicle are the restraint systems: • Three-point lap and shoulder belts for the driver andall passengers • Advanced Front Airbags for driver and front passen-ger • Supplemental Side Airbag Inflatable Curtains (SABIC)for the driver...

WARNING! • It is dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding inthese areas are more likely to be seriously injuredor killed. • Do not allow people to ride in any area of yourvehicle that is not equipped with seats and seatbelts. • Be sure everyone ...

4. Position the lap belt across your thighs, below yourabdomen. To remove slack in the lap belt portion, pull upa bit on the shoulder belt. To loosen the lap belt if it is tootight, tilt the latch plate and pull on the lap belt. A snugbelt reduces the risk of sliding under the belt in acollision. WA...

6. To release the belt, push the red button on the buckle.The belt will automatically retract to its stowed position.If necessary, slide the latch plate down the webbing toallow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision andleave you with no protection. ...

How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward untilthe entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you willhear a clicking sound. This indicates the safety belt isnow in the ...

3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driver’sseat belt at least three times within 10 seconds, endingwith the seat belt buckled. NOTE: Watch for the Seat Belt Reminder Light to turn on while unbuckling the seat belt and turn off while...

WARNING! Using a seat belt extender when not needed canincrease the risk of injury in a collision. Only usewhen the seat belt is not long enough when it is wornlow and snug and in the recommended seating posi-tions. Remove and store the extender when notneeded. Supplemental Restraint System (SRS) - ...

The Advanced Front Airbags have a multistage inflatordesign. This allows the airbag to have different rates ofinflation based on the severity and type of collision. This vehicle may be equipped with driver and/or frontpassenger seat track position sensors that may adjust theinflation rate of the Adv...

• Supplemental Side Airbag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Front Seat Belt Pretensioners, Seat Belt Buckle Switch,and Seat Track Position Sensors Advanced Front Airbag Features The Advanced Front Airbag system has multistage driverand front passenger airbags. This syste...

Supplemental Side Airbag Inflatable Curtain(SABIC) — If Equipped SABIC airbags may offer side-impact and vehicle rolloverprotection to front and rear seat outboard occupants inaddition to that provided by the body structure. Eachairbag features inflated chambers placed adjacent to thehead of each ou...

The system includes side impact sensors adjacent to bothfront and rear seat occupants that are calibrated to deploythe SABIC airbags during impacts that require airbagoccupant protection. WARNING! • If your vehicle is equipped with left and rightSupplemental Side Airbag Inflatable Curtain(SABIC), do...

If the airbag system in this vehicle needs to be modifiedto accommodate a disabled person, contact the CustomerCenter. Phone numbers are provided under ⬙ If You Need Assistance”. WARNING! • Relying on the airbags alone could lead to moresevere injuries in a collision. The airbags work withyour seat ...

Also, the ORC turns on the Airbag WarningLight in the instrument panel for approxi-mately six to eight seconds for a self-checkwhen the ignition is first turned on. After the self-check, the Airbag Warning Light will turn off. If theORC detects a malfunction in any part of the system, itturns on the...

separate and fold out of the way as the airbags inflate totheir full size. The airbags fully inflate in about 50 to 70milliseconds. This is about half of the time it takes toblink your eyes. The airbags then quickly deflate whilehelping to restrain the driver and front passenger. The Advanced Front ...

Enhanced Accident Response System In the event of an impact causing airbag deployment, ifthe communication network remains intact, and thepower remains intact, depending on the nature of theevent the ORC will determine whether to have theEnhanced Accident Response System perform the follow-ing funct...

airbag inflation. These airborne particles may irritatethe skin, eyes, nose, or throat. If you have skin or eyeirritation, rinse the area with cool water. For nose orthroat irritation, move to fresh air. If the irritationcontinues, see your doctor. If these particles settle onyour clothing, follow t...

WARNING! (Continued) • Do not attempt to modify any part of your ad-vanced airbag system. The airbag may inflateaccidentally or may not function properly if modi-fications are made. Take your vehicle to an autho-rized dealer for any advanced airbag system ser-vice. If your seat, including your trim ...

• Pedal position • And other parameters depending on vehicle configuration Child Restraints Everyone in your vehicle needs to be buckled up all thetime, including babies and children. Every state in theUnited States and all Canadian provinces require thatsmall children ride in proper restraint syste...

restraint anchorage system. Refer to “LATCH — ChildSeat Anchorage System (Lower Anchors and Tether forCHildren)”. The belt-positioning booster seat is for children weighingmore than 40 lbs (18 kg), but who are still too small to fitthe vehicle’s seat belts properly. If the child cannot sitwith knees...

All three rear-seating positions have lower anchoragesthat are capable of accommodating LATCH-compatiblechild seats. You should NEVER install LATCH- compatible child seats so that two seats share a commonlower anchorage. If installing child seats in adjacentrear-seating positions, or if your child r...

Again, carefully follow the installation instructions thatare provided with the child restraint system. The rear seat lower anchorages are round barslocated at the rear of the seat cushion where itmeets the seatback and are just visible whenyou lean into the rear seat to install the child restraint....

To attach a child restraint tether strap: 1. Rotate the cover over the anchor directly behind theseat where you are placing the child restraint. 2. Route the tether strap to provide the most direct pathfor the strap between the anchor and the child seat. 3. Attach the tether strap hook (A) of the ch...

WARNING! • Do not leave children or animals inside parkedvehicles in hot weather. Interior heat build-up maycause serious injury or death. • It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, peopleriding in these areas are more likely to be seri-ously ...

UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 87 ▫ Automatic Dimming Mirror — If Equipped . . . 88 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 88...

䡵 Voice Command — If Equipped . . . . . . . . . . . 119 ▫ Voice Command System Operation . . . . . . . . 119 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . 124 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal andvertical mirror adjustment. Adjust the mirror to center onthe view through the rear window. Headlight glare can be reduced by moving the smallcontrol under the mirror to the night position (toward therear of the vehicl...

Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glarefrom vehicles behind you. You can turn the feature on oroff by pressing the button at the base of the mirror. A lightnext to the button will illuminate to indicate when thedimming feature is activated. CAUTIO...

WARNING! Vehicles and other objects seen in the passenger sideconvex mirror will look smaller and farther awaythan they really are. Relying too much on yourpassenger side convex mirror could cause you tocollide with another vehicle or other object. Use yourinside mirror when judging the size or dist...

Power Mirrors The power mirror switch is located on the driver’s doortrim panel, next to the power door lock switch. A rotaryknob selects the left mirror, right mirror or off position. After selecting a mirror, move the knob in the samedirection you want the mirror to move. Use the center offpositio...

Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-free, in-vehicle communications system. Uconnect™ Phone al-lows you to dial a phone number with your cellularphone using simple voice commands (e.g., ⬙ Call” ѧ “Mike” ѧ ”Work ⬙ or ⬙ Dial” ѧ “248-555-1212 ⬙ ). Your cellular pho...

The Uconnect™ Phone can be used with any Hands-FreeProfile certified Bluetooth 威 cellular phone. See the Uconnect™ website for supported phones. If your cellu-lar phone supports a different profile (e.g., HeadsetProfile) you may not be able to use any Uconnect™Phone features. Refer to your cellular ...

The following are general phone to Uconnect™ Phonepairing instructions: • Press the button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing. ⬙ • When prompted, after the beep, say ⬙ Pair a Phone ⬙ and follow the audible prompts. • You will be asked to say a fo...

• Depending on the maximum number of entries down-loaded, there may be a short delay before the latestdownloaded names can be used. Until then, if avail-able, the previous downloaded phonebook is availablefor use. • Only the phonebook of the currently connected cellu-lar phone is accessible. • Only ...

first disconnect or drop the Bluetooth 威 connection to the Uconnect™ Phone, and then send the addressbook entry via Bluetooth 威 . Please see your phone Owner ’s Manual for specific instructions on how todrop the Bluetooth 威 connection. • If the phonebook entry is longer than 24 characters, itwill on...

• After the ignition key is switched to OFF, a call cancontinue on the Uconnect™ Phone either until the callends, or until the vehicle battery condition dictatescessation of the call on the Uconnect™ Phone andtransfer of the call to the cellular phone. • After the ignition key is switched to OFF, a ...

If the phone is not reachable and the Uconnect™ Phone isoperational, you may reach the emergency number asfollows: • Press the button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Emergency ⬙ and the Uconnect™ Phone will instruct the paired cellular phone to call the emergency...

• In a convertible vehicle, system performance may becompromised with the convertible top down. Phone Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry we...

General Information This device complies with Part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions: • Changes or modifications not expressly approved bythe party responsible for compliance could void theuser’s authority to operate the equipment. • T...

NOTE: Keep in mind that you have to press the Voice Command button first and wait for the beep before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recog-nizing their voice commands or numbers the Uconnect™Voice “Voice Training” feature may be use...

Manual Seats — If Equipped The adjusting bar is at the front of the seat, near the floor.Pull the bar upward to move the seat forward or rearward.Release the bar once the seat is in the position desired.Using body pressure, move forward and rearward on theseat to be sure that the seat adjusters have...

Power Seats — If Equipped The power seat switch is located on the outboard side ofthe seat near the floor. Use this switch to move thedriver’s seat up or down, forward or rearward or torecline the seatback. The passenger’s seat will move up ordown, forward or rearward. WARNING! Adjusting a seat whil...

Power Reclining Seats — If Equipped The recliner control is located on the outboard side of theseat. Use the recline control to adjust the forward or rearwardposition of the seatback. WARNING! Do not ride with the seatback reclined so that theshoulder belt is no longer resting against your chest.In ...

Lumbar Support — If Equipped This feature allows you to increase or decrease theamount of lumbar support. Turn the control lever for-ward to increase and rearward to decrease the desiredamount of lumbar support. Head Restraints Head restraints can reduce the risk of injury in the eventof a rear impa...

NOTE: Ensure that the front of the head restraint is facing toward the front of the vehicle. WARNING! Driving a vehicle with the head restraints removed orimproperly adjusted could cause serious injury ordeath in the event of a collision. The head restraintsshould always be checked prior to operatin...

WARNING! • Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes,spinal cord injury, medication, alcohol use, ex-haustion or other physical condition must exercisecare when using the seat heater. It may cause burnseven at low temperatures, especially if us...

When the seatback is folded to the upright position, makesure it is latched by strongly pulling on the top of theseatback above the seat strap. WARNING! • Be certain that the seatback is securely locked intoposition. If the seatback is not securely locked intoposition, the seat will not provide the ...

2. Move to the outside of the vehicle and push the safetycatch to the left. The safety catch is located under thecenter front edge of the hood. Use the hood prop rod (if equipped) to secure the hood inthe open position. CAUTION! To prevent possible damage, do not slam the hood toclose it. Lower the ...

LIGHTS Headlight Switch The headlight switch is located on the left side ofthe instrument panel. This switch controls theoperation of the headlights, parking lights, instru- ment panel lights, instrument panel light dimming, inte-rior lights and fog lights. Rotate the headlight switch clockwise to t...

Headlights On with Wipers (Available withAutomatic Headlights Only) When this feature is active, the headlights will turn onapproximately 10 seconds after the wipers are turned onif the headlight switch is placed in the AUTO position. Inaddition, the headlights will turn off when the wipers areturne...

Daytime Running Lights — If Equipped The high beam headlights will come on as DaytimeRunning Lights whenever the ignition switch is ON, theheadlights are off and the parking brake is off. Theheadlight switch must be used for normal nighttimedriving. Lights-On Reminder If the headlights or parking li...

Flash-to-Pass You can signal another vehicle with your headlights bylightly pulling the multifunction lever toward you. Thiswill turn on the high beams headlights until the lever isreleased. Overhead Console Map/Reading Lights These lights are mounted between the sun visors on theoverhead console. E...

Interior Lights The interior lights come on when a door is opened. To protect the battery, the interior lights will turn offautomatically 10 minutes after the ignition switch ismoved to the LOCK position. This will occur if theinterior lights were switched on manually or are onbecause a door is open...

WINDSHIELD WIPERS AND WASHERS The multifunction lever operates the windshield wipersand washer when the ignition switch is in the ONposition. The lever is located on the left side of thesteering column. Rotate the end of the multifunction lever to the firstdetent past the intermittent settings for l...

Headlights On with Wipers (Available withAutomatic Headlights Only) When this feature is active, the headlights will turn onapproximately 10 seconds after the wipers are turned onif the headlight switch is placed in the AUTO position. Inaddition, the headlights will turn off when the wipers areturne...

outward or push it inward as desired. To lock the steeringcolumn in position, push the control handle inward untilfully engaged. WARNING! Do not adjust the steering column while driving.Adjusting the steering column while driving or driv-ing with the steering column unlocked, could causethe driver t...

• The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the transmission is in REVERSE or when the Electronic Speed Control ison. CAUTION! Do not place any article under the adjustable pedalsor impede its ability to move as...

NOTE: In order to ensure proper operation, the Elec- tronic Speed Control System has been designed to shutdown if multiple Speed Control functions are operated atthe same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the ElectronicSpeed Control ON/OFF button...

To Set At A Desired Speed Turn the Electronic Speed Control ON. When the vehiclereaches the speed desired, push the lever downward toSET DECEL and release. Remove your foot from theaccelerator pedal and the vehicle will operate at theselected speed. NOTE: • Electronic Speed Control will only functio...

RESUME ACCEL position, the set speed will continue toincrease until the lever is released, then the new set speedwill be established. Tapping the Electronic Speed Control lever to RESUMEACCEL once will result in a 1 mph (1.6 km/h) speedincrease. Each time the lever is tapped speed increases, sotappi...

WARNING! Electronic Speed Control can be dangerous where thesystem cannot maintain a constant speed. Your ve-hicle could go too fast for the conditions and youcould lose control. An accident could be the result.Do not use Electronic Speed Control in heavy trafficor on roads that are winding, icy, sn...

These lights also turn on when a door is opened, whenthe UNLOCK button on the Remote Keyless Entry (RKE)transmitter is pressed, or when the dimmer control isturned fully upward, past the second detent. Sunglasses Storage At the rear of the console, a compartment is provided forthe storage of a pair ...

WARNING! • Your motorized door or gate will open and closewhile you are training the Universal Transceiver.Do not train the transceiver if people, pets, orother objects are in the path of the door or gate.Only use this transceiver with a garage dooropener that has a “stop and reverse” feature asrequ...

2. Place the handheld transmitter 1 to 3 in (3 to 8 cm)from the HomeLink 威 buttons while keeping the EVIC display in view. For optimal training, point the battery end of the hand-held transmitter away from the HomeLink 威 . 3. Simultaneously, press and hold both the chosenHomeLink 威 button and the ha...

Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig-nals to “time-out” (or quit) after several seconds oftransmission – which may not be long enough forHomeLink 威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are...

General Information This device complies with FCC rules Part 15 and IndustryCanada RSS-210. Operation is subject to the followingtwo conditions: 1. This device may not cause harmful interference 2. This device must accept any interference that may bereceived including interference that may cause und...

Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing,press the switch forward and hold for two seconds afterthe reversal occurs. This allows the sunroof to movetoward the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — ...

Ignition Off Operation For vehicles not equipped with the Electronic VehicleInformation Center (EVIC), the power sunroof switchwill remain active for 10 minutes after the ignition switchis turned OFF. Opening either front door will cancel thisfeature. For vehicles equipped with the EVIC, the power s...

CAUTION! (Continued) • Power outlets are designed for accessory plugsonly. Do not hang any type of accessory or acces-sory bracket from the plug. Improper use of thepower outlet can cause damage. CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of thecenter console. Fr...

Rear Seat Cupholders The rear seat cupholders are located in the center armrestbetween the rear seats. The cupholders are positionedforward in the armrest and side-by-side to provideconvenient access to beverage cans or bottles whilemaintaining a resting place for the rear occupants elbows. STORAGE ...

LOAD LEVELING SYSTEM — IF EQUIPPED The automatic load leveling system will provide a level-riding vehicle under most passenger and cargo loadingconditions. A hydraulic pump contained within the shock absorbersraises the rear of the vehicle to the correct height. It takesapproximately 1 mile (1.6 km)...

UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 170 䡵 Instrument Cluster – Base . . . . . . . . . . . . . . . 171 䡵 Instrument Cluster – Premium . . . . . . . . . . . . 172 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 173 䡵 Electronic...

▫ Operating Instructions — Voice CommandSystem (VR) — If Equipped . . . . . . . . . . . . . 202 ▫ Operating Instructions — Uconnect™ Phone— If Equipped . . . . . . . . . . . . . . . . . . . . . . 202 ▫ Clock Setting Procedure — RBZ Radio . . . . . 202 ▫ Clock Setting Procedure —RER/REN Radio . . . ....

INSTRUMENT PANEL FEATURES 1 — Air Outlet 7 — Climate Control 13 — Hood Release 2 — Instrument Cluster 8 — Heated Seat Switch* 14 — Trunk Release Button 3 — Hazard Switch 9 — Power Outlet 15 — Headlight Switch 4 — Electronic Stability Program OFF Button* / Traction Control System OFF Button* 10 — Ash...

INSTRUMENT CLUSTER – BASE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 171

INSTRUMENT CLUSTER – PREMIUM 172 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank whenthe ignition switch is in the ON position. 2. Trip Odometer Button Premium Cluster Press this button to change the display from odometer toeither of two trip odometer settings. The letter “A” or “B...

6. Charging System Warning Light This light shows the status of the electrical charg-ing system. The light should turn on when the ignition switch is first turned ON and remain on brieflyas a bulb check. If the light stays on or turns on whiledriving, turn off some of the vehicle’s non-essentialelec...

The gauge pointer will likely indicate a higher tempera-ture when driving in hot weather, up mountain grades,or when towing a trailer. It should not be allowed toexceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system coulddamage your vehicle. If the ...

26. Door Ajar Indicator This light will turn on to indicate that one or moredoor may be ajar. 27. Decklid Ajar Indicator This light will turn on to indicate that thedecklid may be ajar. 28. Windshield Washer Fluid Low Indicator This light will turn on to indicate the windshieldwasher fluid is low. E...

Press the AUDIO MODE button to select theCompass/Temp/Audio screen. Along withcompass reading and outside temperature, thisscreen will display radio and media modeinformation depending on which radio is in thevehicle. Refer to “Remote Sound SystemControls”. Electronic Vehicle Information Center (EVI...

• ECO (Fuel Saver Indicator) — if equipped • SERVICE AWD SYSTEM — All Wheel Drive (AWD)system is not functioning properly and service isrequired. • Channel # Transmit • Channel # Training • Channel # Trained • Clearing Channels • Channels Cleared • Did Not Train • Insert Key/Turn To Run (refer to “R...

2. Fully depress the accelerator pedal slowly three timeswithin 10 seconds. 3. Turn the ignition switch to the LOCK position. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did notreset. If necessary, repeat this procedure. Trip Functions Press...

To Reset The Display Reset will only occur while a resettable function is beingdisplayed. Press and release the FUNCTION SELECTbutton once to clear the resettable function being dis-played. To reset all resettable functions, press and releasethe FUNCTION SELECT button a second time withinthree secon...

Compass Display The compass readings indicate the directionthe vehicle is facing. Press and release theHOME button to display one of eight compassreadings and the outside temperature. NOTE: The system will display the last known outside temperature when starting the vehicle and may need tobe driven ...

5. Complete one or more 360 degree turns (in an area freefrom large metal or metallic objects) until the “CAL”message turns off. The compass will now functionnormally. Compass Variance Compass Variance is the difference between MagneticNorth and Geographic North. To compensate for thedifferences, th...

3. Press the SCROLL button until “Compass Variance”message and the last variance zone number displays inthe EVIC. 4. Press and release FUNCTION SELECT button untilthe proper variance zone is selected according to themap. 5. Press and release the HOME button to exit. Navigation — If Equipped Navigati...

Press and release the MENU button until Personal Set-tings displays in the EVIC. Use the SCROLL button to display one of the followingchoices. “Language” When in this display you may select one of five lan-guages for all display nomenclature, including the tripfunctions and the navigation system (if...

press and release the FUNCTION SELECT button until“Driver Door 1st Press” or “All Doors 1st Press” appears. “Sound Horn with Remote Key Lock” When ON is selected, a short horn sound will occur whenthe RKE transmitter LOCK button is pressed. This featuremay be selected with or without the Flash Light...

“Confirmation of Voice Commands” — IfEquipped When ON is selected, all voice commands from theUconnect™ system are confirmed. To make your selec-tion, press and release the FUNCTION SELECT buttonuntil “ON” or “OFF” appears. “Turn-by-Turn Navigation” — If Equipped When ON is selected, the turn-by-tur...

2. Touch the screen where the time is displayed. Theclock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear inthe box next to the words “Daylight Savings.” Touch thescreen where the words “Daylight Savings” are dis-played to change the current setting. Show...

satellite clock is Greenwich Mean Time (GMT). This is theworldwide standard for time. This makes the system’sclock very accurate once the appropriate time zone anddaylight savings information is set. To Manually Set the Clock — RER/REN 1. Turn on the radio. 2. Touch the screen where the time is disp...

Show Time if Radio is Off When selected, this feature will display the time of dayon the touch screen when the radio is turned off. Proceedas follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displa...

MEDIA CENTER 130 (RES) — AM/FM STEREORADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Con...

SEEK Buttons Press and release the SEEK buttons to search for the nextlistenable station in AM/FM mode. Press the right switchto seek up and the left switch to seek down. The radiowill remain tuned to the new station until you makeanother selection. Holding either button will bypassstations without ...

Push the rotary TUNE/SCROLL control knob a secondtime and MID will display. Turn the TUNE/SCROLLcontrol knob to the right or left to increase or decrease themid-range tones. Push the rotary TUNE/SCROLL control knob a thirdtime and TREBLE will display. Turn the TUNE/SCROLLcontrol knob to the right or...

SET 2 in both AM and FM. This allows a total of 12 AMand 12 FM stations to be stored into pushbutton memory.The stations stored in SET 2 memory can be selected bypressing the pushbutton twice. Every time a preset button is used, a correspondingbutton number will display. Buttons 1 - 6 These buttons ...

If you insert a disc with the ignition ON and the radioON, the unit will switch from radio to CD mode andbegin to play when you insert the disc. The display willshow the track number, and index time in minutes andseconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept...

TIME Button Press this button to change the display from a large CDplaying time display to a small CD playing time display. RW/FF Press and hold the FF (Fast Forward) button and the CDplayer will begin to fast forward until FF is released, orRW or another CD button is pressed. The RW (Reverse)button...

The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of filenames and folder names is limited. For large numbersof files and/or folders, the radio may be unable todisplay the file nam...

rates (VBR) are also supported. The majority of MP3 filesuse a 44.1 kHz sampling rate and a 192, 160, 128, 96 orVBR bit rate. MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224,192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer ...

Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, whichallows the user to plug in a portable device, such as anMP3 player, or cassette player, and utilize the vehicle’saudio system to amplify the source and play through thevehicle speakers. Pressing the DISC/AU...

NOTE: Ejecting with the ignition OFF is not allowed on convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on theCD. Press the left SEEK button to return to the beginningof the current selection, or return to the beginning of theprevious selec...

Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack whichallows the user to plug in a portable device such as anMP3 player or cassette player and utilize the vehicle’saudio system to amplify the source and play through thevehicle speakers. Pressing the AUX button ...

information, call the toll-free number 888-539-7474, orvisit the Sirius web site at www.sirius.com, or at www-.siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius IdentificationNumber (ESN/SID) Please have the following information available whencalling: 1. The Electronic Serial ...

Reception Quality Satellite reception may be interrupted due to one of thefollowing reasons: • The vehicle is parked in an underground parkingstructure or under a physical obstacle. • Dense tree coverage may interrupt reception in theform of short audio mutes. • Driving under wide bridges or along t...

SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish tocommit to pushbutton memory, press the SET button.The symbol SET 1 will now show in the display window.Select the button (1-6) you wish to lock onto this channeland press and release that button. If a button i...

• RND button (available on sales code RES radio only): Pressing this button toggles between Shuffle ON andShuffle OFF modes for the iPod 威 . If the RND icon is showing on the radio display, then the shuffle mode isON. List Or Browse Mode During Play mode, pressing any of the buttons describedbelow, ...

VIDEO ENTERTAINMENT SYSTEM (VES)™ — IFEQUIPPED The optional Video Entertainment System (VES)™ in-cludes the following components for rear seat entertain-ment: • A diagonal 7 in (17.8 cm) Liquid Crystal Display (LCD)screen integrated into the center console armrest. Thescreen features brightness cont...

• The LCD screen swings up from the rear of the armrestto allow the rear seat passenger(s) to view the display. NOTE: Close the armrest after the LCD screen has been raised to its viewing position. • The radio and DVD player controls allow front seatoperation for easy setup in the case of younger re...

• Two wireless infrared headsets allow rear seat passen-gers to listen to the same or individual audio sources. Audio/Video RCA Jacks (AUX Jacks)on the rear of the center console enablethe monitor to display video directlyfrom a video camera, connect videogames for display on the screen, orplay musi...

Center (EVIC). The EVIC features a driver-interactivedisplay which is located in the instrument cluster. The VOLUME button controls the soundlevel of the sound system. Press the top ofthe VOLUME button to increase the soundlevel. Press the bottom of the VOLUMEbutton to decrease the sound level. Pres...

CD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the followingprecautions: 1. Handle the disc by its edge; avoid touching thesurface. 2. If the disc is stained, clean the surface with a soft cloth,wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch-in...

CLIMATE CONTROLS The air conditioning and heating system is designed tomake you comfortable in all types of weather. Manual Air Conditioning and Heating System Blower Control The rotary knob on the left controls theblower. The control has an OFF posi-tion and four speed settings. The blower will rem...

Temperature Control The rotary knob in the center controlsair temperature. Rotate the control tothe left for cooler air temperature andto the right for warmer air tempera-ture. Rotating the control to the ex-treme left provides the coldest setting.Rotating the control to the extreme right provides t...

• Bi-Level Air flows through the outlets located in the instru-ment panel and through the outlets located on the floor. Air flows through the registers in the back of thecenter console to the rear seat passengers. These registerscan be closed to partially block airflow. • Panel Air flows through the...

Automatic Temperature Control — If Equipped Automatic Operation The Dual-Zone Climate Control System automaticallymaintains the climate in the cabin of the vehicle at thecomfort levels desired by the driver and passenger. Operation of the system is quite simple. Begin by turningthe mode control knob...

• Extended use of recirculation may cause the windowsto fog. If the interior of the windows begin to fog, pressthe recirculation button to return to outside air. Sometemp/humidity conditions will cause captured inte-rior air to condense on windows and hamper visibility.For this reason, the system wi...

conditioning. An indicator in the button illuminateswhen manual compressor operation is selected. NOTE: To control the air conditioning manually, the mode selector must be moved out of the AUTO position. • Recirculation Control This button can be used to block out smoke,odors, dust, high humidity, o...

Winter Operation Use of the air Recirculation mode during Winter monthsis not recommended because it may cause windowfogging. Vacation Storage Any time you store your vehicle or keep it out of service(i.e., vacation) for two weeks or more, run the airconditioning system at idle for about five minute...

Control Setting Suggestions for Various Weather Conditions 4 UNDERSTANDING YOUR INSTRUMENT PANEL 257

STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 263 ▫ Automatic Transmission . . . . . . . . . . . . . . . 263 ▫ Normal Starting (Tip Start) . . . . . . . . . . . . . 264 ▫ Extreme Cold Weather (Below ⫺ 20°F Or ⫺ 29°C) . . . . . . . . . . . . . . . . . ....

▫ Tire Identification Number (TIN) . . . . . . . . . 300 ▫ Tire Terminology And Definitions . . . . . . . . . 301 ▫ Tire Loading And Tire Pressure . . . . . . . . . . 302 䡵 Tires — General Information . . . . . . . . . . . . . 306 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . 306 ▫ T...

▫ E85 Usage In Non-Flex Fuel Vehicles . . . . . . 327 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . 328 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . 329 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . 329 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . 330 䡵 Adding...

Normal Starting (Tip Start) NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing theaccelerator pedal. Do not press the accelerator. Use the Fob with Integrated Key to briefly turn the ignition switch to the STARTposition and release it as soon as the start...

The engine block heater cord is routed under the hood onthe driver side of the vehicle. It has a removable cap thatis located on the driver side of the Integrated PowerModule. WARNING! Remember to disconnect the cord before driving.Damage to the 110-115 Volt electrical cord could causeelectrocution....

• The electronically-controlled transmission provides aprecise shift schedule. The transmission electronics areself-calibrating. Therefore, the first few shifts on a newvehicle may be somewhat abrupt or soft until after thebreak-in period. This is a normal condition, and pre-cision shifts will devel...

This may result in a slightly different feeling or responseduring normal operation in the DRIVE position. After thetransmission cools down, it will return to normaloperation. Key Ignition Park Interlock This vehicle is equipped with a Key Ignition Park Inter-lock which requires the shift lever to be...

4. Using the screwdriver, press and hold the override tabthrough the access port on the center console. 5. Move the shift lever into the NEUTRAL position. 6. The vehicle may then be started in NEUTRAL. 7. Reinstall the override cover. Four-Speed Automatic Transmission – IfEquipped NOTE: Under extrem...

Gear Ranges PARK This range supplements the parking brake by locking thetransmission. The engine can be started in this range.Never use PARK while the vehicle is in motion. Applythe parking brake when leaving the vehicle in this range. When parking on a flat surface, place the shift lever in thePARK...

“D” (Overdrive) This range is used for most city and highway driving. Itprovides the smoothest up shifts and down shifts and thebest fuel economy. Select the “3” range when frequenttransmission shifting occurs when using the Overdriverange, such as when operating the vehicle under heavyloading condi...

occur only to prevent engine overspeed while downshiftsoccur earlier than in other gear range selections. CAUTION! Never race the engine with the brakes on and thevehicle in gear, and never hold the vehicle on anincline without applying the brakes. These practicescan cause overheating and damage to ...

Transmission Limp Home Mode The transmission is monitored for abnormal conditions.If a condition is detected that could cause damage, thetransmission automatically shifts into second gear. Thetransmission remains in second gear despite the forwardgear selected. PARK, REVERSE, and NEUTRAL willcontinu...

If vehicle acceleration worsens, or the transmission nolonger shifts, the transmission is most likely operating inthe Limp Home Mode. In this mode, the transmissionwill remain in the current gear until the vehicle isbrought to a stop. After the vehicle has stopped, PARK,REVERSE, and NEUTRAL will con...

Electronic Range Select (ERS) – If Equipped Electronic Range Select (ERS) allows the driver to limitthe highest available transmission gear, providing youwith more control of the vehicle. ERS allows you tomaximize engine braking, eliminate undesirable upshifts,and improve overall vehicle performance...

vehicle automatically shifts into AWD mode. AutomaticAWD operation could be activated by outside tempera-ture, wheel slip, or other predetermined conditions (theremay be a slight delay for AWD engagement after a wheelslip condition occurs). AWD can also be manually se-lected by moving the shift leve...

WARNING! Rapid acceleration on slippery surfaces is dangerous.Unequal traction can cause sudden pulling of the rearwheels. You could lose control of the vehicle andpossibly have an accident. Accelerate slowly andcarefully whenever there is likely to be poor traction(ice, snow, wet mud, loose sand, e...

Flowing/Rising Water WARNING! Do not drive on or across a road or path where wateris flowing and/or rising (as in storm run-off). Flow-ing water can wear away the road or path’s surfaceand cause your vehicle to sink into deeper water.Furthermore, flowing and/or rising water can carryyour vehicle awa...

checked if a leak is suspected, abnormal noises areapparent, and/or the system is not functioning as antici-pated. Coordinate inspection efforts through an autho-rized dealer. CAUTION! Do not use chemical flushes in your power steeringsystem as the chemicals can damage your powersteering components....

The foot operated parking brake is located below thelower left corner of the instrument panel. To apply thepark brake, firmly push the park brake pedal fully. Torelease the parking brake, press the park brake pedal asecond time and let your foot up as you feel the brakedisengage. When the parking br...

ANTI-LOCK BRAKE SYSTEM The Anti-Lock Brake System (ABS) provides increasedvehicle stability and brake performance under mostbraking conditions. The system automatically “pumps”the brakes during severe braking conditions to preventwheel lock-up. The Electronic Brake Force Distribution (EBD) preventst...

ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronicbrake control system that include Anti-Lock Brake Sys-tem (ABS), Traction Control System (TCS), Brake AssistSystem (BAS), and the Electronic Stability Program (ESP).All four of these systems work together to enhancev...

The ESP system has two available operating modes: ESP On This is the normal operating mode for the ESP. Wheneverthe vehicle is started, the ESP system will be in this mode.This mode should be used for most driving conditions.The ESP should only be turned OFF for specific reasonsas noted in the follo...

TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S.design standards. P-Metric tires have the letter “P”molded into the sidewall preceding the size designa-tion. Example: P215/65R15 95H. • European-Metric tire sizing is based on Europeandesign standards. ...

Tires designed to this standard have the letter “T”molded into the sidewall preceding the size designa-tion. Example: T145/80D18 103M. • High flotation tire sizing is based on U.S. designstandards and it begins with the tire diameter moldedinto the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Char...

EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions— The maximum speed corresp...

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire,however, the date code may only be on one side. Tireswith white sidewalls will have the full TIN, including thedate code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of bl...

Tire Terminology and Definitions Term Definition B-Pillar The vehicle B-Pillar is a structural member of the body locatedbetween the front and rear door (of a four-door vehicle) runningfrom the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after th...

Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the:1) number of people that can be carried in the vehicle2) total weigh...

Loading The vehicle maximum load on the tire must not exceedthe load carrying capacity of the tire on your vehicle. Youwill not exceed the tire’s load carrying capacity if youadhere to the loading conditions, tire size, and cold tireinflation pressures specified on the Tire and LoadingInformation pl...

CAUTION! After inspecting or adjusting the tire pressure, al-ways reinstall the valve stem cap. This will preventmoisture and dirt from entering the valve stem,which could damage the valve stem. Inflation pressures specified on the placard are always“cold tire inflation pressure.” Cold tire inflatio...

WARNING! Temporary use spare tires are for emergency use only.With these tires, do not drive more than 50 mph(80 km/h). Temporary use spare tires have limitedtread life. When the tread is worn to the tread wearindicators, the temporary use spare tire needs to bereplaced. Be sure to follow the warnin...

WARNING! The limited-use spare tires are for emergency useonly. Installation of this limited-use spare tire affectsvehicle handling. With this tire, do not drive morethan 50 mph (80 km/h). Keep inflated to the cold tireinflation pressure listed on either your tire placard orlimited-use spare tire an...

Tread Wear Indicators Tread wear indicators are in the original equipment tiresto help you in determining when your tires should bereplaced. These indicators are molded into the bottom of the treadgrooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn ...

Keep dismounted tires in a cool, dry place with as littleexposure to light as possible. Protect tires from contactwith oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of manycharacteristics. They should be inspected regularly forwear and correct cold tire...

These effects can be reduced by timely rotation of tires.The benefits of rotation are especially worthwhile withaggressive tread designs such as those on all season typetires. Rotation will increase tread life, help to maintainmud, snow and wet traction levels, and contribute to asmooth, quiet ride....

NOTE: • The TPMS is not intended to replace normal tire careand maintenance or to provide warning of a tire failureor condition. • The TPMS should not be used as a tire pressure gaugewhile adjusting your tire pressure. • Driving on a significantly under-inflated tire causesthe tire to overheat and c...

5. Once you repair or replace the original road tire, andreinstall it on the vehicle in place of the compact spare,the TPMS will update automatically and the TPM TelltaleLight will turn OFF, as long as no tire pressure is belowthe low-pressure warning limit in any of the four activeroad tires. The v...

Tire Pressure Monitoring Low Pressure Warnings The TPM Telltale Light will illuminate in theinstrument cluster and a chime will sound whentire pressure is low in one or more of the four active road tires. In addition, the EVIC will display one ormore low pressure messages (Left Front, Left Rear, Rig...

turn off. The vehicle may need to be driven for up to20 minutes above 15 mph (25 km/h) in order for theTPMS to receive this information. Check TPMS Warning If a system fault is detected, the TPM Telltale Light willflash on and off for 75 seconds and then remain on solid.The system fault will also so...

FUEL REQUIREMENTS 2.7L Engine The 2.7L engine is designed to meet allemissions regulations and provide excel-lent fuel economy and performance whenusing high-quality unleaded “regular”gasoline having an octane rating of 87. Theuse of premium gasoline is not recom- mended, as it will not provide any ...

If a Non-FFV vehicle is inadvertently fueled with E85fuel, the engine will have some or all of these symptoms: • operate in a lean mode • OBD II “Malfunction Indicator Light” on • poor engine performance • poor cold start and cold driveability • increased risk for fuel system component corrosion To ...

Materials Added to Fuel All gasoline sold in the United States is required tocontain effective detergent additives. Use of additionaldetergents or other additives is not needed under normalconditions and they would result in additional cost.Therefore, you should not have to add anything to thefuel. ...

NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler cap doorreinforcement. CAUTION! • Damage to the fuel system or emissions controlsystem could result from using an improper fueltank filler tube cap (gas cap). (Continued) Fuel Filler Door Gas Cap Teth...

CAUTION! (Continued) • A poorly fitting gas cap could let impurities intothe fuel system. • A poorly fitting gas cap may cause the “Malfunc-tion Indicator Light (MIL)” to turn on. • To avoid fuel spillage and overfilling, do not “topoff” the fuel tank after filling. When the fuelnozzle “clicks” or s...

”gASCAP” message will appear in the odometer or a“Check Gascap” message will display in the ElectronicVehicle Information Center (EVIC) (if equipped). If thisoccurs, tighten the fuel filler cap properly and press theTRIP ODOMETER button to turn off the message. If theproblem continues, the message w...

Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.This includes driver, passengers, and cargo. The totalload must be limited so that you do not exceed theGVWR. Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rearaxles. Distrib...

WARNING! • An improperly adjusted weight distributing hitchsystem may reduce handling, stability, brakingperformance, and could result in an accident. • Weight distributing systems may not be compat-ible with surge brake couplers. Consult with yourhitch and trailer manufacturer or a reputable rec-re...

Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. (See Note) 2.7L & 3.5L Rear WheelDrive (RWD) Automatic 22 sq ft...

Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight inthe front of the trailer. This places 10% to 15% of theGross Trailer Weight (GTW) on the tow hitch of yourvehicle. Loads balanced over the wheels or heavier in therear can cause the trailer to sway severely side to side ...

NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additionalfactory-installed options or dealer-installed options mustbe considered as part of the total load on your vehicle.Refer to the “Tire and Loading Information” placard forthe maximum combined we...

− An electronically actuated trailer brake controller is required when towing a trailer with electronicallyactuated brakes. When towing a trailer equipped witha hydraulic surge actuated brake system, an electronicbrake controller is not required. − Trailer brakes are recommended for trailers over 1,...

The Trailer Tow Package may include a four and seven-pin wiring harness. Use a factory approved trailer har-ness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehiclebut you must mate the harness to a trailer con...

Towing Tips Before setting out on a trip, practice turning, stopping,and backing up the trailer in an area located away fromheavy traffic. Automatic Transmission The DRIVE range can be selected when towing. How-ever, if frequent shifting occurs while in this range, selecta lower gear range using the...

specified for “police, taxi, fleet, or frequent trailer tow-ing.” Refer to “Maintenance Schedule” for the propermaintenance intervals. Electronic Speed Control – If Equipped − Do not use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops greater than ...

RECREATIONAL TOWING (BEHINDMOTORHOME, ETC.) Two-Wheel Drive and All-Wheel Drive Recreational towing (with all four wheels on the ground)is allowed ONLY if the rear driveshaft is removed and the transmission is in NEUTRAL (for both RWD andAWD vehicles). WARNING! If the driveshaft is removed, the vehi...

WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 350 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 350 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 351 ▫ Jack Location/Spare Tire Stowage . . . . . . . . 352 ▫ Preparations For Jacki...

HAZARD WARNING FLASHER The Hazard Warning flasher switch is located in theswitch bank near the top center of the instrument panel. Press the switch to turn on the Hazard Warningflasher. When the switch is activated, all directionalturn signals will flash on and off to warn oncoming traffic of an eme...

CAUTION! Driving with a hot cooling system could damageyour vehicle. If the temperature gauge reads “H,”pull over and stop the vehicle. Idle the vehicle withthe air conditioner turned off until the pointer dropsback into the normal range. If the pointer remains onthe “H,” turn the engine off immedia...

WARNING! (Continued) • The jack is designed to use as a tool for changingtires only. The jack should not be used to lift thevehicle for service purposes. The vehicle shouldbe jacked on a firm level surface only. Avoid ice orslippery areas. Jack Location/Spare Tire Stowage The jack and spare tire are...

4. Remove the spare tire. 5. Remove the fastener securing the jack. WARNING! A loose tire or jack thrown forward in a collision orhard stop could endanger the occupants of the ve-hicle. Always stow the jack parts and the spare tire inthe places provided. Spare Tire Fastener Jack Fastener 6 WHAT TO D...

Preparations for Jacking 1. Park the vehicle on a firm, level surface as far from theedge of the roadway as possible. Avoid icy or slipperyareas. WARNING! Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough offthe road to avoid being hit when operating ...

WARNING! (Continued) • Block the wheel diagonally opposite the wheel tobe raised. • Set the parking brake firmly and set an automatictransmission in PARK; a manual transmission inREVERSE. • Never start or run the engine with the vehicle on ajack. • Do not let anyone sit in the vehicle when it is on ...

2. If equipped with steel wheels, do not remove thewheel cover at this time. If equipped with aluminumwheels where the center cap covers the lug nuts, use thelug wrench to pry the center cap off carefully beforeraising the vehicle. WARNING! To avoid possible personal injury, handle the wheelcovers w...

5. Raise the vehicle just enough to remove the flat tireand install the spare tire. WARNING! Raising the vehicle higher than necessary can makethe vehicle less stable. It could slip off the jack andhurt someone near it. Raise the vehicle only enoughto remove the tire. 6. Remove the lug nuts, wheel c...

avoid the risk of forcing the vehicle off the jack, do nottighten the lug nuts fully until the vehicle is lowered tothe ground. 9. Lower the vehicle to the ground by turning the jackhandle counterclockwise. 10. Finish tightening the lug nuts. Push down on thewrench while tightening for increased lev...

3. Align the valve notch in the wheel cover with thevalve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use ahammer or excessive force to install the cover. 4. Install the remaining lug nuts with the cone shapedend of the nut toward the wheel. Lightly...

7. For vehicles equipped with center caps, install thecenter cap by hand. Do not use a hammer or excessiveforce to install the center cap. 8. Stow the jack, tools, and spare tire. Make sure the baseof the jack faces the rear of the vehicle before tighteningdown the fastener. WARNING! A loose tire or...

Preparations for Jump-Start The battery is stored under an access cover in the trunk.Remote battery posts are located on the right side of theengine compartment for jump-starting. NOTE: The remote battery posts are viewed by standing on the right side of the vehicle looking over the fender. Remote B...

WARNING! • Take care to avoid the radiator cooling fan when-ever the hood is raised. It can start anytime theignition switch is on. You can be injured bymoving fan blades. • Remove any metal jewelry such as watch bands orbracelets that might make an inadvertent electricalcontact. You could be seriou...

8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the remote positive (+) post of the discharged vehicle. If frequent jump-starting is required to start your vehicleyou should...

Towing This Vehicle Behind Another Vehicle Flatbed towing is recommended. DO NOT tow an AWDvehicle with the rear wheels on the ground unless therear driveshaft is removed and the transmission is inNEUTRAL. Vehicles WITHOUT AWD may be towed (with rearwheels on the ground) with the transmission in NEU...

CAUTION! (Continued) • Do not push or tow this vehicle with anothervehicle as damage to the bumper fascia and trans-mission may result. If you must use the accessories (wipers, defrosters, etc.)while being towed, the key must be in the ON position,not the ACC position. Make certain the transmissionr...

MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.7L . . . . . . . . . . . . . 373 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . . 374 䡵 Engine Compartment — 5.7L . . . . . . . . . . . . . 375 䡵 Onboard Diagnostic System — OBD II . . . . . . 376 ▫ Loose Fuel Filler Cap . . . . . . . ....

▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . 390 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 391 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 393 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 399 ▫ Automatic Transmission . . . . . . . . . . . . ...

ENGINE COMPARTMENT — 2.7L 1 — Integrated Power Module 6 — Air Cleaner Filter 2 — Engine Oil Dipstick 7 — Engine Oil Fill 3 — Brake Fluid Reservoir Access Cover 8 — Remote Jump Start (Positive Battery Post) 4 — Engine Coolant Reservoir 9 — Washer Fluid Reservoir 5 — Power Steering Fluid Reservoir 7 M...

ENGINE COMPARTMENT — 3.5L 1 — Integrated Power Module 6 — Engine Oil Fill 2 — Air Cleaner Filter 7 — Engine Oil Dipstick 3 — Brake Fluid Reservoir Access Cover 8 — Remote Jump Start (Positive Battery Post) 4 — Engine Coolant Reservoir 9 — Washer Fluid Reservoir 5 — Power Steering Fluid Reservoir 374...

ENGINE COMPARTMENT — 5.7L 1 — Integrated Power Module 6 — Air Cleaner Filter 2 — Coolant Pressure Cap 7 — Engine Oil Fill 3 — Brake Fluid Reservoir Access Cover 8 — Engine Oil Dipstick 4 — Engine Coolant Reservoir 9 — Remote Jump Start (Positive Battery Post) 5 — Power Steering Fluid Reservoir 10 — ...

TRIP ODOMETER button to turn off the message. If theproblem continues, the message will appear the next timethe vehicle is started. A loose, improperly installed, or damaged fuel filler capmay also turn on the MIL. EMISSIONS INSPECTION AND MAINTENANCEPROGRAMS In some localities, it may be a legal re...

your vehicle. Refer to these Service Manuals beforeattempting any procedure yourself. NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civilpenalties being assessed against you. WARNING! You can be badly injured working on or around amotor vehicle...

Synthetic Engine Oils You may use synthetic engine oils provided the recom-mended oil quality requirements are met, and the recom-mended maintenance intervals for oil and filter changesare followed. Materials Added to Engine Oil Do not add any supplemental materials, other than leakdetection dyes, t...

Engine Air Cleaner Filter Refer to “Maintenance Schedule” for further information. WARNING! The air induction system (air cleaner, hoses, etc.) canprovide a measure of protection in the case of enginebackfire. Do not remove the air induction system (aircleaner, hoses, etc.) unless such removal is ne...

WARNING! • Battery fluid is a corrosive acid solution and canburn or even blind you. Do not allow battery fluidto contact your eyes, skin, or clothing. Do not leanover a battery when attaching clamps. If acidsplashes in eyes or on skin, flush the area imme-diately with large amounts of water. • Batt...

WARNING! (Continued) • The battery in this vehicle has a vent hose thatshould not be disconnected and should only bereplaced with a battery of the same type (vented). CAUTION! • It is essential when replacing the cables on thebattery that the positive cable is attached to thepositive post and the ne...

WARNING! • Use only refrigerants and compressor lubricantsapproved by the manufacturer for your air condi-tioning system. Some unapproved refrigerants areflammable and can explode, injuring you. Otherunapproved refrigerants or lubricants can causethe system to fail, requiring costly repairs. Refer t...

1. Remove the access door in the cowl screen by pressingthe retaining clips. 2. Slide the lid on the filter adapter forward and downand remove the used filter. 3. Install the new filter with arrows pointing in thedirection of airflow, which is toward the rear of thevehicle (text and arrows on the fi...

Refer to “Maintenance Schedule” for the proper mainte-nance intervals. Body Lubrication Locks and all body pivot points, including such items asseat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri-cated periodically with a lithium based...

Windshield Wiper Blades Clean the rubber edges of the wiper blades and thewindshield periodically with a sponge or soft cloth and amild nonabrasive cleaner. This will remove accumula-tions of salt or road film. Operation of the wipers on dry glass for long periodsmay cause deterioration of the wiper...

The fluid reservoir will hold nearly 1 gal (4 L) of washerfluid when the message “Low Washer Fluid” appears inthe Electronic Vehicle Information Center (EVIC) (ifequipped). WARNING! Commercially available windshield washer solventsare flammable. They could ignite and burn you. Caremust be exercised ...

NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessedagainst you. In unusual situations involving grossly malfunctioningengine operation, a scorching odor may suggest severeand abnormal catalyst overheating. If this occurs, stopthe vehicle, turn off ...

Coolant Checks Check engine coolant (antifreeze) protection every12 months (before the onset of freezing weather, whereapplicable). If the engine coolant (antifreeze) is dirty orrusty in appearance, the system should be drained,flushed, and refilled with fresh coolant. Check the frontof the radiator...

CAUTION! • Mixing of engine coolant (antifreeze) other thanspecified HOAT engine coolant (antifreeze), mayresult in engine damage and may decrease corro-sion protection. If a non-HOAT engine coolant(antifreeze) is introduced into the cooling systemin an emergency, it should be replaced with thespeci...

Please review these recommendations for using HybridOrganic Additive Technology (HOAT) engine coolant(antifreeze). When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR 威 Antifreeze/Coolant 5 Year/100,000 Mile FormulaHOAT (Hybrid Organic Additive Technology) orequivalent...

When additional engine coolant (antifreeze) is needed tomaintain the proper level, it should be added to thecoolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor comingfrom the front of the engine comp...

Fluid and Filter Changes Refer to “Maintenance Schedule” for further information. If the transmission is disassembled for any reason, thefluid and filter should be changed. Selection of Lubricant It is important that the proper lubricant is used in thetransmission to assure optimum transmission perf...

All Wheel Drive (AWD) – If Equipped The all wheel drive system consists of a transfer case andfront differential. The exterior surface of these compo-nents should be inspected for evidence of fluid leaks.Confirmed leaks should be repaired as soon as possible. The transfer case fluid fill/inspection ...

• Use a high quality cleaner wax, such as MOPAR 威 Cleaner Wax or equivalent to remove road film, stainsand to protect your paint finish. Take care never toscratch the paint. • Avoid using abrasive compounds and power buffingthat may diminish the gloss or thin out the paintfinish. CAUTION! • Do not u...

• If you carry special cargo such as chemicals, fertilizers,de-icer salt, etc., be sure that such materials are wellpackaged and sealed. • If a lot of driving is done on gravel roads, considermud or stone shields behind each wheel. • Use MOPAR 威 Touch Up Paint or equivalent on scratches as soon as p...

To minimize the possibility of scratching the lenses andreducing light output, avoid wiping with a dry cloth. Toremove road dirt, wash with a mild soap solution fol-lowed by rinsing. Do not use abrasive cleaning components, solvents, steelwool or other aggressive material to clean the lenses. Glass ...

Replace the belts if they appear frayed or worn or if thebuckles do not work properly. Cleaning the Center Console Cupholders Clean with a damp cloth or towel using a mild detergentwith the cupholder in the center console. NOTE: The cupholder cannot be removed. FUSES Integrated Power Module The Inte...

CAUTION! • When installing the integrated power modulecover, it is important to ensure the cover is prop-erly positioned and fully latched. Failure to do somay allow water to get into the integrated powermodule and possibly result in an electrical systemfailure. • When replacing a blown fuse, it is ...

Cavity Car-tridgeFuse Mini-Fuse Description 9 — — — 10 30 AmpPink — Windshield Wiper 11 30 AmpPink — Anti-Lock Brake System(ABS) Valves – IfEquipped 12 40 AmpGreen — Radiator Fan 13 50 AmpRed — Anti-Lock Brake System(ABS) Pump Motor – IfEquipped 14 — — — Cavity Car-tridgeFuse Mini-Fuse Description 1...

Rear Power Distribution Center There is also a power distribution center located in thetrunk under the spare tire access panel. This centercontains fuses and relays. Opening The Access Panel Rear Power Distribution Center 412 MAINTAINING YOUR VEHICLE

Cavity Car-tridgeFuse Mini-Fuse Description 5 30 AmpPink — Heated Seats – IfEquipped 6 — 20 AmpYellow Fuel Pump 7 — — — 8 — 15 AmpBlue Diagnostic Link Connec-tor (DLC)/Wireless Con-trol Module (WCM)/Wireless Ignition Node(WIN) 9 — 20 AmpYellow Power Outlet 10 — — — 11 * — — — 12 * — — — Cavity Car-t...

Cavity Car-tridgeFuse Mini-Fuse Description 22 — — — 23 — — — 24 — — — 25 — — — 26 — — — 27 — 10 AmpRed Occupant Restraint Con-troller (ORC) 28 — 10 AmpRed Ignition Run, AC HeaterControl/Headlights/Occupant Restraint Con-troller (ORC) 29 — 5 AmpOrange Cluster/Electronic Sta-bility Program (ESP) – If...

Cavity Car-tridgeFuse Mini-Fuse Description 38 — 10 AmpRed Cargo Light/SatelliteReceiver (SDARS) Video– If Equipped/VehicleInformation Module – IfEquipped 39 — 10 AmpRed Heated Mirrors – IfEquipped 40 — 5 AmpOrange Auto Inside RearviewMirror – If Equipped/Heated Seats – IfEquipped/Switch Bank 41 — —...

Low Beam Headlamp, High Beam Headlamp, andPark/Turn Lamp — Models with High IntensityDischarge Headlamps (HID) HID Headlamps The headlamps are a type of high voltage discharge tube.High voltage can remain in the circuit even with theheadlamp switch off and the key removed. Because of this, you shoul...

Backup Lamp, Side Marker Lamp, Tail/Turn Lamp,and Tail/Stop Lamp 1. Open the trunk. 2. Remove two fasteners from the back of the taillampassembly. 3. Pull back the trunk liner. 4. Remove the remaining fastener from the back of thetaillamp assembly. 5. Push the electrical connector locking tab to the...

11. Reinstall the taillamp assembly, fasteners, electricalconnector, and trunk liner. 12. Close the trunk. License Lamp 1. Remove the screws securing the lamp to the rearfascia. 2. Remove the bulb and socket assembly. 3. Disconnect the bulb from the socket assembly andinstall the replacement bulb. 4...

FLUID CAPACITIES U.S. Metric Fuel (Approximate) 2.7 Liter Engine 18 Gallons 68 Liters 3.5 Liter Engine without All Wheel Drive 18 Gallons 68 Liters 3.5 Liter Engine with All Wheel Drive 19 Gallons 72 Liters 5.7 Liter Engine 19 Gallons 72 Liters Engine Oil with Filter 2.7 Liter Engine (SAE 5W-20, API...

U.S. Metric Cooling System * 2.7 Liter Engine (MOPAR 威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 9.9 Quarts 9.4 Liters 3.5 Liter Engine without All Wheel Drive (MOPAR 威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula or equivalent) 11.1 Quarts 10.5 Liters 3.5 Liter Engine with Al...

MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 432 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 432 ▫ Required Maintenance Intervals . . . . . . . . . . 434 8 M A I N TE N A N C E SC H E DU LE S

EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensurethe continued proper functioning of the emissions controlsystem. These and all other maintenance services in-cluded in this manual, should be done to p...

• Check the fluid levels of the coolant reservoir, brakemaster cylinder, and power steering, add as needed. • Check all lights and other electrical items for correctoperation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to perform the requ...

IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For YourVehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453 ▫ Prepare For The Appointment . . . . . . . . . . . 453 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 453 ▫ Be Reasonable With R...

This is why you should always talk to an authorizeddealer’s service manager first. Most matters can be re-solved with this process. • If for some reason you are still not satisfied, talk to thegeneral manager or owner of the authorized dealer-ship. They want to know if you need assistance. • If an a...

Customer Assistance For The Hearing Or SpeechImpaired (TDD/TTY) To assist customers who have hearing difficulties, themanufacturer has installed special TDD (Telecommuni-cation Devices for the Deaf) equipment at its customercenter. Any hearing or speech impaired customer, whohas access to a TDD or a...

We appreciate that you have made a major investmentwhen you purchased the vehicle. An authorized dealerhas also made a major investment in facilities, tools, andtraining to assure that you are absolutely delighted withthe ownership experience. You’ll be pleased with theirsincere efforts to resolve a...

If NHTSA receives similar complaints, it may open aninvestigation, and if it finds that a safety defect exists ina group of vehicles, it may order a recall and remedycampaign. However, NHTSA cannot become involved inindividual problems between you, your authorizeddealer, and the manufacturer. To con...

Auto Unlock, Doors . . . . . . . . . . . . . . . . . . . . . . . 31Auto Up Power Windows . . . . . . . . . . . . . . . . . . 37Automatic Dimming Mirror . . . . . . . . . . . . . . . . . 88Automatic Door Locks . . . . . . . . . . . . . . . . . . . 30,31Automatic Headlights . . . . . . . . . . . . . ....

Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 165Defroster, Windshield . . . . . . . . . . . . . . . . 80,248,254Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . 140Diagnostic System, Onboard . . . . . . . . . . . . . . . . 376Dimmer Switch, Headlight . . . . . . . . . . ...

Filler Location Fuel . . . . . . . . . . . . . . . . . . . . . . 330Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 384Air Conditioning . . . . . . . . . . . . . . . . . . . . 256,387Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 383,428Engine Oil Disposal . . . ....

Daytime Running . . . . . . . . . . . . . . . . . . . . . . 136Dimmer Switch, Headlight . . . . . . . . . . . . . 136,137Electronic Stability Program (ESP) Indicator . . . 296Electronic Throttle Control Warning . . . . . . . . . 174Engine Temperature Warning . . . . . . . . . . . . . . 176Exterior ....

Warning (Instrument Cluster Description) . . . . . 173 Load Leveling System . . . . . . . . . . . . . . . . . . . . 166Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . 333,335 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 335Tires . . . . . . . . . . . . . . . . . . . ....

Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Mode Fuel Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 Modifications/Alterations, Vehicle . . . . . . . . . . . . . 7Monitor, Tire Pressure System . . . . . . . . . . . . . . . 315Mopar Parts . . . . . . . . ....

Outside Rearview Mirrors . . . . . . . . . . . . . . . . . . 88Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273Overhead Console . . . . . . . . . . . . . . . . . . . . . . . 148Overheating, Engine . . . . . . . . . . . . . . . . . . . 175,350Owner’s Manual (Operator Manual) . ...

Sunglasses Storage . . . . . . . . . . . . . . . . . . . . . . . 149Sunroof Maintenance . . . . . . . . . . . . . . . . . . . . . 157Supplemental Restraint System - Airbag . . . . . . . . 52Sway Control, Trailer . . . . . . . . . . . . . . . . . . . . . 337Synthetic Engine Oil . . . . . . . . . . . ...

Chrysler Group LLC 10D481-126-AC 3rd Edition Printed in U.S.A.