Page 3 - INDEX
WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emitchemicals known to the State of California tocause cancer and birth defects or otherreproductive harm. INDEX Features And Controls ...........................................................................
Page 4 - FEATURES
Page 5 - General Information; Safety Procedures; GENERAL INFORMATION
5 General Information This manual will assist you in the safe operation andproper maintenance of your Dixon equipment. Read itthoroughly before attempting to operate the machine.Call your dealer or Dixon if additional information isrequired. The following safety symbols are used throughout themanual...
Page 6 - Assembly Instructions; Front Weight Bar; SAFETY INFORMATION
6 Assembly Instructions Front Weight Bar Tools Required Ratchet with 3 / 8 " Socket 3 / 8 " Wrench Mounting Instructions • Using the weight keepers, attach front weight barto mower at the front caster arms. • Secure front weight bar to mower frame with four 3 / 8 " x 1¼" hex bolts, f...
Page 7 - ASSEMBLY; Collection System
7 STRAP LANYARD SUPPORTBRACKET ASSEMBLY Collection System Tools Required RatchetTorque Wrench½" Wrench½" Socket 9 / 16 " Wrench 9 / 16 " Socket 5 / 8 " Socket 1. Open the mounting kit box and remove all of thecomponents. 2. Place the support bracket on the frame andsecure with (2...
Page 8 - Handle Assembly
8 Handle Assembly 1. Attach backing plate and tube support to hopperusing holes shown in illustration. 2. Connect handle to tube support using pivot pin. ASSEMBLY BACKING PLATEHOLES BACKINGPLATE TO HOPPERUNIT TUBESUPPORT STOP PIVOT PIN THREADED TUBE HANDLE ADJUSTMENTNUT ROD END ADJUSTMENTNUT ROD END...
Page 9 - Hopper Door Adjustment; Blower Kit
9 ASSEMBLY Hopper Door Adjustment Adjust door rods on both sides with adjusting nut sodoor closes evenly. See illustration. DOORRODS ADJUSTMENT NUTS HOPPER HOPPER DOOR Blower Kit Install Blower Kit per the instructions shipped with theblower unit. (114992 for the 52" or 130195 for the 60".) ...
Page 10 - Preventative Maintenance Schedule; SERVICE AND MAINTENANCE; Cleaning and Washing
10 Preventative Maintenance Schedule Item Before Every Every Every Each Use 5 Hours 25 Hours 50 Hours Inspect/Clean Poly Mesh X X Check/Tighten Nuts & Bolts X Check/Tighten Hoses X Turn Hose End to End X Rotate Hose X Clean Machine X SERVICE AND MAINTENANCE WARNING The collection system hopper m...
Page 11 - Troubleshooting Guide; Caring For Hoses; Cleaning Poly Mesh
11 PROBLEM POSSIBLE CAUSE CORRECTION Loss of Vacuum. Blower, hose or hood inlet clogged. Remove hose and clean inlet. Hopper full. Inspect and empty. Fan blades bent or broken. Replace/repair impeller. Poly mesh plugged. Clean poly mesh. Unusual vibration Solid object jammed in unit. Check and remov...
Page 12 - HOPPER ASSEMBLY
12 1 ...... 1 .... 113754 ....... WELDMENT - HOPPER2 ...... 8 .... 104808 ....... PILLOW BLOCK3 ...... 1 .... 113747 ....... WELDMENT - DOOR4 ...... 1 .... 113755 ....... PLATE - BACKING5 ...... 1 .... 113748 ....... TUBE - SUPPORT, HANDLE6 ...... 1 .... 113746 ....... WELDMENT - BELL CRANK7 ...... ...
Page 13 - DRIVE KIT ASSEMBLY
13 DRIVE KIT ASSEMBLY 1 .... 1 ... 111199 ...... HITCH BRKT WELDMENT, LT2 .... 1 ... 111201 ...... HITCH BRKT WELDMENT, RT3 .... 1 ... 20255 ........ FRONT WEIGHT BAR4 .... 1 ... 111313 ...... HOLD DOWN, WEIGHT BAR5 .... 2 ... 102049 ...... CLEVIS PIN6 .... 2 ... 108096 ...... SPRING RETAINER7 .... ...
Page 14 - HOOD ASSEMBLY
14 1 ... 539 111172 .... 1 .. HOOD2 ... 539 111175 .... 2 .. SUPPORT, DRAW LATCH3 ... 539 111182 .... 1 .. INLET TUBE4 ... 539 111183 .... 1 .. MESH, POLY DIAMOND5 ... 539 102587 .... 6 .. GROMMET, BUMPER6 ... 539 105408 .. 2 1 .. WASHER, #10 HOOD ASSEMBLY ITEM P/N QTY. DESCRIPTION ITEM P/N QTY. DES...