Directed Electronics G322R - Manual

5 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. Please note that it is necessary to k...

7 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . iin nsstta alllla attiio on n Be sure to read this section thoroughly and view the Rattler Do- It-Yourself Installation Video in its entirety before starting the installation. Pay special attention to all warnings to prevent personal injury...

8 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 1 Plug-in LED and Valet ® /Program switch The LED and the Valet ® /Program switch both plug into the control module. The status LED plugs into the white two-pin port, while the Valet ® /Program switch should be plugged into the blue tw...

9 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . feed the wires through the hole and press the switch firmly until it snaps into place. Run the wires to the same location as the LED using caution to NOT run the wires near any moving objects or excessive heat. step 2 Ground Wire The BLACK ...

10 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 3 Constant Power and Ignition wires Almost all power and ignition wires can be found behind the key cylinder under the lower drivers side dash panel. Using the appropriate hand tools, remove the lower dash panel using care not to brea...

12 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 4 Starter wire The starter wire will be located in the same harness as the ignition and constant power. Leaving the meter black lead connected to the metal ground. Find the wire suspected to be the starter wire according to the web in...

13 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . Connect the BLACK starter kill wires as shown below. Use one of these wires as the starter kill input and the other as a starter kill output wire (these wires are interchangeable). step 5 Parking light flash There are several different typ...

14 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . Once you have identified the correct wire, solder the WHITE wire on the main connector to it and cover the connection with electrical tape. step 6 Door triggers The door trigger is the circuit in the vehicle that tells the domelight to com...

15 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . black lead of the meter and probe the suspect wire with the dooropen, you will see 11.00 to 13.00 volts appear on the meter,secure the black meter lead to the suspect wire and close the doorwith the display on the meter visible, if you hav...

16 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 7 Dome light supervision (optional) The dome light wire is optional and not required for normal operation, however if desired you can have the security system turn on the dome light when the system is disarmed. If you would like this ...

17 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 9 Optional connections (channel 2, 3) When the system receives the code controlling channel 2, for longer than 1.5 seconds, the RED/WHITE wire (H1/12- channel 2) will supply an output as long as the transmission continues. This is oft...

18 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 10 Hood/trunk pins The BLUE (H1/6) wire will respond to a negative input with an instant trigger. It is ideal for hood and trunk pins and will report on Zone 1. It can also be used with Directed Electronics 506T Glass Breakage Sensor,...

19 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . step 12 Testing the system With all the previous steps completed, the operation of thesystem can now be tested. ■ Close all the doors and press the button on the transmitter, the system should chirp one time. ■ At this point the system wil...

20 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . work correctly check your wiring against the manual and verify all connections. If you still are experiencing problems contact Rattler technical support. ttrra an nssm miitttte err ffu un nc cttiio on nss The receiver uses a computer-based...

21 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . standard configuration Button The arm/disarm function is controlled by pressing . Button This channel 2 accessory is used for trunk release. Button This channel 3 accessory is an additional channel for optional accessory functions such as ...

24 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . Auto Learn function This function provides a 1–step programming of the transmitter to the following factory default settings: ➤ Button —Lock/Unlock ➤ Button —Channel 2 output ➤ Button —Channel 3/Instant output Delete all Transmitters In ca...

26 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . 4. T Trraan nssm miitt.. While H HO OL LD DIIN NG G the Valet ® /Program switch, you can select the desired feature settings using the remote trans- mitter. Pressing Button while H HO OL LD D-- IIN NG G down the Valet ® /Program switch wil...

27 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . 4. The siren will chirp two times to confirm that you have accessed Feature 2, Confirmation Chirps. to exit the learn routine To exit the learn routine, do one of the following: 1. Close the open doors. 2. Turn the ignition on. 3. No activ...

28 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . ffe ea attu urre ess m me en nu u The factory defaults are indicated in bold text in the table below. note: The number in parentheses indicate the number of times the LED will flash. The Factory defaults are indi-cated in b boolld d type. ...

30 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . u ussiin ng g yyo ou urr ssyysstte em m arming with transmitter Pressing for one second will arm the system. The parking lights will flash once and the siren will chirp once to confirm that the system is armed. arming without a transmitter...

31 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . ➤ Heavy impacts will trigger the system. The triggeredsequence is 30-seconds of constant siren sounding andflashing parking lights. ➤ If a protected entry (door, hood, or trunk) is opened, thesystem will immediately trigger the siren and f...

32 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . disarming without a transmitter If your remote transmitter is lost or damaged, you can manually disarm your vehicle security system. To disarm the system without a transmitter, you must have the vehicle's ignition key and know where the Va...

33 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . will flash for 30-seconds. To stop the Panic Mode at any time, press again. silent mode Use the Silent Mode to temporarily turn off the arm or disarm chirps by briefly pressing before pressing the when arming or disarming. The confirmation...

34 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . manual valet mode T Too een ntteerr oorr eexxiitt V Vaalleett M Mood dee w wiitth h tth hee V Vaalleett ® ® //P Prrooggrraam m ssw wiittcch h:: 1. Turn the ignition on. 2. Turn the ignition off. 3. Press and release the Valet ® /Program sw...

35 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . d diia ag gn no ossttiic css The microprocessor at the heart of your system has the ability to constantly monitor all of the switches and sensors connected to it. It can detect any faulty switches or sensors and prevent them from disabling...

36 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . disarming diagnostics Your system has a Tamper Alert feature that notifies you of system triggers that occur while you are away from your vehicle. If you hear four chirps when you disarm, this indicates that the system was triggered in you...

37 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . system status chirps ACTION NUMBER OF CHIPS DESCRIPTION Arm 1 System armed Arm 1 (3-second delay), 1 System armed with Bypass Notification Disarm 2 System disarmed Disarm 4 System disarmed with Tamper Alert Disarm 5 System disarmed NPC® ac...

38 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . table of zones A zone is represented by the number of LED flashes used by the system to identify a particular type of input. Standard input assignments are listed in the following table, along with spaces to write in any optional sensors o...

40 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . c co od de e h ho op pp piin ng g ™ rre e--ssyyn nc ch hrro on niizze e If the transmitter is pressed many times out of range, or the battery is removed, the transmitter may get temporarily out of synchronization and fail to operate the sy...

41 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . Are the door inputs connected? Is the H1/6 blue wire connected to the door trigger wire in the vehicle? Either the H1/5 green or the H1/7 violet should be used instead. (See Primary Harness Wire Connection Guide section of this guide.) ➤ D...

47 © 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . n no otte ess _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________...

The company behind this system is Directed Electronics, Inc. Since its inception, Directed Electronics has had one purpose, to provide consumers withthe finest vehicle security and car stereo products and accessories available. The recipient ofnearly 100 patents and Innovations Awards in the field o...