Directed Electronics 5 - Manual

3 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . important information Congratulations on the purchase of your state-of-the-art vehicle security system. It has been designed to provide years of trouble-free operation. This system must be installed by an authorized dealer. Installation of ...

4 fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or...

5 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . transmitter functions This system uses computer-based code learning to learn the transmitterbuttons. This makes it possible to assign any transmitter button to anysystem function. The transmitter initially comes programmed with stan-dard co...

6 using your system The buttons used in the instructions in this manual correspond to the standard transmitter configuration. If your transmitter has been custom configured, the icons on your transmitter buttons may not correspond to the indicated functions. arming You can activate, or arm, the syst...

9 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . transmitter sensor disable To temporarily disable a sensor input, arm the system, press the and simultaneously. The lights will flash four times and all warn away trigger zones three and eight are bypassed. Press the buttons again; the ligh...

© 2 0 0 3 d i r e c t e d e l e c t r o n i c s , i n c . auxiliary channel bypass Alarm sensor input zones three and eight will be bypassed while a pulsed or timed auxiliary Output is active. panic mode with smart door locking If you are threatened in or near your vehicle, you can attract attention...

11 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . 3. After the last digit continue to hold for three seconds. The LED status indicator will light steadily if you are entering Valet Mode and will turn off if you are exiting Valet Mode. To exit Valet Mode: 1. Turn the ignition on. 2. Within...

13 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . multiple event total recall This will report the last eight system triggers. 1. Press and hold of the PlainView 2 Valet switch. 2. While still holding , arm and disarm the system, then release the button. 3. The LED will start to blink to ...

14 Doors are covered by FACT II differently; if the alarm is triggered by an open door for three full cycles, the doors will be bypassed until the trig- ger ceases. FACT II is programmable. See the Programming Options section of this guide. select siren sounds Selectable siren sounds are available w...

15 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . Press on the PlainView 2 Valet switch while playing the desired sound to add that sound; press while playing the desired sound to delete that sound. diagnostics The microprocessor at the heart of your security system is constantly monitori...

16 disarming diagnostics Extra disarm chirps are the Tamper Alert. If three chirps are heard when disarming, the system was triggered in your absence. If three chirps are heard, the LED status indicator will indicate which zone was involved (see the Table of Zones section). The system will retain th...

18 high frequency Your system transmits and receives at 433 MHz. This provides a cleaner spectrum with less interference and a more stable signal. smart power up II This security system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall ...

19 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . z Power Saver in Valet Mode: When the system enters ValetMode the LED illuminates steadily. If the vehicle is not used(ignition is not turned on) for a period of one hour while thesystem is in Valet Mode, the LED will shut off. If the syst...

20 locking allows the vehicle's doors to lock when the securitysystem passively arms (after the 30 second countdown). Thisfeature only works if passive arming has been programmed. z Panic mode enabled /disabled: Some states have laws against siren capability. z Full trigger response 30 , 60, or 90 s...

23 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . auto arm - on/ off z On: When the system sees the ignition turn off and the lastprotected entry (door, hood, or trunk) close, it will begin a30-second countdown before arming itself. After the firstfive seconds, you will hear two chirps an...

24 passive lock - on/ off z On: The doors will lock when the system passively arms. Thisfeature only applies when passive arming is programmed on. z Off: The doors will not lock when the system passively arms. siren duration - 30 /60/90 z The system will sound the alarm for the programmed dura-tion ...

26 panic on/off z On: The panic feature is available. z Off: The panic feature is not available. user selectable features descriptions - column three The features in this column pertain to programming individual trans- mitter channels in custom configurations. Following is an explanation of the feat...

28 pin programming A PIN code can have one to four digits; each digit can be from 0-9. Programming Procedure 1. Enter the feature location in the installer programming grid. 2. Immediately press and release of the PlainView 2 Valet switch. 3. Select each digit by pressing 1-9 times, and then press t...

29 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set. 1. Turn on the ignition. 2. Enter the new PIN code. 3. Press and hold for three seconds. z LED tu...

31 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . security & convenience expansions Here we have listed only some of the many expansion options avail- able. Please contact your dealer for a complete list of all the options available to you. Backup Battery: The 520T keeps the system ar...

33 © 2 0 0 4 d i r e c t e d e l e c t r o n i c s , i n c . health check Directed Electronics recommends you return to your installing Clifford dealer to have your system checked for correct operation. The first check is due one year after the installation date and at yearly intervals thereafter.

Vista, CA 92081 www.directed.com © 2004 Directed Electronics, Inc. - All rights reserved G909595 08/04 The company behind this system is Directed Electronics, Inc. Since its inception, Directed ® has had one purpose, to provide consumers with the finest vehi- cle security and car stereo products and...