Page 6 - Arm Button
7 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s 2 2--w wa ayy rre em mo otte e c co on nttrro oll d diia ag grra am m 1. Arm/Disarm Indicator (Orange) 2. Receive/Transmit Indicator (Green) 3. Auxiliary Indicator (Yellow) 4. Siren Indicator (Red) 5. Arm Button 6. Disarm Button 7. Panic Button 8. Au...
Page 8 - On both remotes the panic button is the same color.
9 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s w wh ha att iiss iin nc cllu ud de ed d ➤ One control module ➤ One four-button LED 2-way transmitter, 488XD ➤ One four-button transmitter, 7141X ➤ Wire harnesses ➤ Dual diode harness ➤ The 514N six-tone programmable siren ➤ The in-vehicle status LED ...
Page 9 - system maintenance; Low Battery Notification; your warranty
10 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s system maintenance This system needs no specific maintenance beyond 2-way remote control battery replacement. The 2-way remote is powered by a 1.5V AAA battery. The 1-way remote is powered by a pair of 3V CR2016 batteries. Low Battery Notification I...
Page 11 - The 2-way remote control buttons are used to send commands; standard configuration; Button
12 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s 2 2--w wa ayy rre em mo otte e c co on nttrro oll ffu un nc cttiio on nss The 2-way remote control buttons are used to send commands to the system. The descriptions below reflect the standard config- uration for this system. The buttons can be custo...
Page 12 - and Buttons
13 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously. The auxiliary output controls_________________________. and Buttons An optional auxilia...
Page 14 - system signal paging features; Command Page
15 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s rre em mo otte e o op pe erra attiio on n The system operates at 434 MHz and incorporates Directed’s propri- etary out-board technology transceiver. The high frequency combined with Binary Data communication achieves superior range with two- way com...
Page 15 - out of range notification
16 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s until the alarm page is cleared. If the shock sensor or optional sensor has triggered the alarm the remote will display the alarm page with 6 Red LED flashes and 10 rapid beeps. If the trunk, door, ignition, or hood triggered the alarm the remote wi...
Page 16 - To enter programming mode
17 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s p prro og grra am mm miin ng g 2 2--w wa ayy rre em mo otte e To enter programming mode Press and hold all four remote control buttons simultaneously until one long beep is heard. Programming mode is now entered. Beeps On/Off Press to select beeps O...
Page 17 - To exit programming mode; active arming; If programmed Off, no alarms will be notified to the
18 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s To exit programming mode The 2-way LED remote control will exit programming mode after 2-seconds of inactivity and will emit 2 long beeps. u ussiin ng g yyo ou urr ssyysstte em m The buttons described in this manual correspond to the standard config...
Page 18 - passive arming
19 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s The 2-way remote responds to active arming with one beep and the Orange LED will flash 3-times to indicate successful arming of the system. If after 2-seconds the remote beeps once and the Orange and Red LEDs flash 3-times, the system has detected a...
Page 19 - When armed your vehicle is protected as follows:; Light impacts trigger the Warn Away; If any protected entry point (such as a door or a
20 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s When armed your vehicle is protected as follows: ➤ Light impacts trigger the Warn Away ® signal. When triggered, the siren chirps and the parking lights flash for a few seconds. ➤ Heavy impacts trip a Triggered Sequence. The sequenceconsists of the ...
Page 20 - multi-level security arming; Table
21 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s multi-level security arming Multi-Level Security Arming allows you to select which of the security system's inputs or sensors will be active and which will be bypassed at the time that the system is armed. (See the Table of Zones section of this gui...
Page 21 - disarming; Diagnostics; Multi-Level Security Arming only applies to a sin-
22 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s After each press of the to reach the next level of security, the remote will emit normal arm notification (1 beep and 3 flashes of the Orange LED). For easiest operation in reaching each level of security, press immediately aafftteerr each notificat...
Page 22 - disarming without a transmitter
23 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s disarming without a transmitter This feature allows you to disarm the security system without the remote transmitter should it be lost, damaged, or disabled. In order to disarm the system without a remote transmitter, you must have the vehicle’s ign...
Page 23 - dome light control; security only; factory; silent mode; The Warn Away
24 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s dome light control security only The dome light activates for 30-seconds after the system is disarmed. Ignition controlled The dome light activates for 30-seconds after the ignition is turned On. door controlled The dome light activates for 30-secon...
Page 24 - panic mode
25 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s The 2-way remote responds with the normal arm/disarm notifi- cations in silent mode. (If the remote has beeps programmed On, the remote will beep.) panic mode 2-way remote If you are threatened in or near your vehicle, you can attract attention by t...
Page 25 - valet mode; To enter or exit Valet Mode:
26 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s Mode at any time, press , or on the remote trans- mitter again. valet mode You can prevent your security system from automatically arming and triggering by using Valet Mode. This is very useful when washing the vehicle or having it serviced. In Vale...
Page 27 - nuisance prevention; Example; Programming Options; Arming and disarming the system does not reset this
28 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s nuisance prevention ® circuitry Your system has Directed’s Nuisance Prevention ® Circuitry (NPC ® ). It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such asthunder, jackhammers, airport n...
Page 29 - enter shock sensor adjustment mode; note; :: Prior to performing this procedure the system
30 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s ssh ho oc ckk sse en nsso orr a ad djju ussttm me en ntt enter shock sensor adjustment mode 1. Press and hold and buttons for 6-seconds. 2. The system will emit 1 long chirp to indicate entry into shock adjustment mode. 3. The LED will illuminate co...
Page 30 - exit shock sensor adjustment mode
31 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s 2. Decrease Sensitivity—Press and release the button to decrease shock sensor sensitivity by one step. The siren will chirp 1-time for each step decreased in adjustment. When the shock sensor adjustment reaches minimum sensitivity (sensor is Off ) t...
Page 31 - diia; System Status Chirps; arming diagnostics; Bypass Notification will not occur when using
32 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s 2. The system will emit 3 chirps to indicate the sensor has been reset to level 10. 3. The system returns to shock sensor adjustment mode for further adjustment, if required. d diia ag gn no ossttiic css The microprocessor at the heart of your secur...
Page 32 - disarming diagnostics; Table of Zones; system status chirps
33 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s if your vehicle has interior light exit delay, and you arm the system before the interior light goes out, you may hear Bypass Notification chirps. Once the light shuts off, however, the doors are monitored normally. disarming diagnostics Extra disar...
Page 33 - Action
34 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s Action Number of Chirps Description Arm 1 System armed Arm 1 (3-second delay), 1 System armed with Bypass Notification Disarm 2 System disarmed Disarm 4 System disarmed with Tamper Alert Disarm 5 System disarmed NPC ® active
Page 34 - table of zones; of LED Flashes
35 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s table of zones The zone number is the number of LED flashes used by thesystem to identify that input. The standard input assignmentsare listed below, along with spaces to write in any optionalsensors or switches you have had installed. Zone - Number...
Page 35 - interpreting zone diagnostics
36 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s interpreting zone diagnostics Warn Away responses are not reported by arming or disarmingdiagnostics. If you receive a Bypass notification when arming ora Tamper Alert notification when disarming, look at the in-vehicle status LED. Active or trigger...
Page 36 - Owner Recognition cannot be programmed with-
37 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s of the transmitter several times within range of the vehicle. The alarm will automatically re-sync and respond to the trans- mitters normally. o ow wn ne err rre ec co og gn niittiio on n Owner Recognition is a feature available exclusively from Dir...
Page 38 - When programmed for passive arming and active
39 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s p prro og grra am mm miin ng g Programming options control what your system does duringnormal operation, and require few or no additional parts.However, some may require additional installation labor. The following is a list of the program settings,...
Page 39 - When the system passively arms after one hour, the
40 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s ➤ Panic mode een naab blleed d/disabled with the ignition on: Some states have laws against siren capability in a moving vehicle. ➤ Forced passive arming oon n or off: If your system is programmed for passive arming and the forced passive arming fea...
Page 42 - arming the vrs; Any installation that allows this product to
43 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s ensure that if your vehicle is taken by an unauthorized user, it will be disabled (after several progressive warnings) as safely as possible. Should a carjacking occur, the VRS ® allows you to concern yourself with your personal safety without worry...
Page 43 - vrs; Fifteen seconds
44 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s door is opened and closed. If you are forced from the vehicle, the system will trigger as the door is opened and closed. This is how the system works to combat intersection carjacking. To protect against parking lot carjacking, arm the VRS ® before ...
Page 44 - Three minutes; disarming the vrs
45 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s Three minutes after the constant siren output begins, the flashing parking lights and the siren will stop. The starter kill will remain active until the system is disarmed. If the door is opened or the ignition is turned off and on in an attempt to ...
Page 45 - Automatic Engine Disable
46 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s 1. Turn the ignition on. 2. Press the Valet button the pre- programmed number of times to disarm the VRS ® system. p prro og grra am mm miin ng g o op pttiio on nss See your dealer for further details on the options listed below available with this ...
Page 46 - Forced Passive Arming; Grouped Arming
47 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s Forced Passive Arming : If passive arming is on and a door is left open the system will be armed after 30-seconds. High Security Disarm: If the system is triggered this feature allows the user to silence the siren and reset the system to the armed s...
Page 47 - Retained Accessory Power
48 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s Retained Accessory Power : This output from the security system can be connected to vehicle accessories. After the ignition has been turned off, it will continue to supply power until a door has been open and closed. sse ec cu urriittyy & & ...
Page 48 - Headlight and Parking Light Automation:
49 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s using the 519H2 garage door opener with your remote control. Ask you dealer for details. Additional parts and labor required. Headlight and Parking Light Automation: The 545T Nite-Lite ® will automatically turn on your parking and headlights when it...
Page 49 - Ullttrraassoon
50 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s U Ullttrraassoon niicc SSeen nssoorr:: Providing a field of protection inside your car using the 509U Ultrasonic sensor to protect your belongings.
Page 51 - Transmitter
52 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s Transmitter : Hand-held, remote control which operates the various functions of your system. Trigger or Triggered Sequence: This is what happens when the alarm "goes off " or "trips". The triggered response of your system consists of...
Page 52 - QUICK REFERENCE GUIDE
53 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s QUICK REFERENCE GUIDE To arm using your 2-way remote ➤ You can activate, or arm, the system by pressing on your remote for one second. When the system arms, you will hear a short siren sound, or chirp, andthe parking lights will flash once. If the v...
Page 53 - The company behind this system is Directed Electronics
Directed Electronics Vista, CA 92081 www.directed.com © 2006 Directed Electronics - All rights reserved G3202X 11-06 The company behind this system is Directed Electronics Since its inception, Directed has had one purpose, to provide consumers with thefinest vehicle security and car stereo products ...
