Digi MIL-4711H - Manual

Digi MIL-4711H – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – Install Guide; M i c r o M o d u l e s u s e d w i t h t h e M I L - 4 7 1 1 H :; For instructions on configuring the micro modules, see the; D e s c r i p t i o n o f H a r d w a r e; MICROHUB
Page 3 – D e s c r i p t i o n o f t h e L E D s; link; The SYS and COL LEDs blink when the unit is operational.; D e s c r i p t i o n o f D i p S w i t c h e s
Page 4 – T h e D B - 9 S e r i a l P o r t; Figure 4.RS-232C Serial Port Pin Assignments; I n s t a l l a t i o n P r o c e d u r e; Follow these steps to connect the MIL-4711H to your network:; The voltage in use is visible.; The factory setting is 120VAC.; the network. Refer to the
Page 5 – A s s i g n i n g a n I P A d d r e s s; alpha
Page 6 – Warning: Entering monitor will lock out
Page 7 – S e t t i n g t h e I P A d d r e s s w i t h B O O T P; To s e t t h e I P A d d r e s s w i t h B O O T P o n a H P / U X s y s t e m :
Page 8 – Use the following menu sequence in sam:; Ethernet; and then click on; Apply
Page 9 – L e g a l; R e g u l a t o r y A p p r o v a l s; C a n a d i a n E M I N o t i c e; Address: 1299 Orleans Drive; Five-Year Limited Warranty

Loading the manual

Doc. Number: 75425 Rev. A

M I L - 4 7 1 1 H

M a n ag e a bl e H u b

U s e r ’s G u i d e

This guide includes the following information:

“Description of Hardware” on page 2

“Description of the LEDs” on page 3

“Description of Dip Switches” on page 3

“The DB-9 Serial Port” on page 4

“Installation Procedure” on page 4

“Assigning an IP Address” on page 5

“Setting the IP Address with Telnet” on page 5

“Setting the IP Address with RARP” on page 6

“Setting the IP Address with BOOTP” on page 7

“Verifying the IP Address is Set Properly” on page 8

“Legal” on page 9

MICROHUB

10BASET MANAGED HUB WITH MODULAR UPLINK MODEL MIL¥4711H

LINK

RECEIVE

PARTITION

LINK

RECEIVE

PARTITION

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Install Guide; M i c r o M o d u l e s u s e d w i t h t h e M I L - 4 7 1 1 H :; For instructions on configuring the micro modules, see the; D e s c r i p t i o n o f H a r d w a r e; MICROHUB

Install Guide Model: MIL-4711H 2 M i c r o M o d u l e s u s e d w i t h t h e M I L - 4 7 1 1 H : • MIL-4310M • MIL-4320M • MIL-4330M • MIL-4340M • MIL-4350M • MIL-4360M • MIL-4370M For instructions on configuring the micro modules, see the MIL-4300M Series Micro Module Installation Guide .. D e s ...

Page 3 - D e s c r i p t i o n o f t h e L E D s; link; The SYS and COL LEDs blink when the unit is operational.; D e s c r i p t i o n o f D i p S w i t c h e s

Install Guide Model: MIL-4711H 3 Figure 3.MIL-4711 (Rear View w/ the MIL-4310 Module) D e s c r i p t i o n o f t h e L E D s On the front panel of the MIL-4711H, there is one LED above each of the eight, 10BASE-T ports. If the port is in use, the LED will change to one of three colors to indicate t...

Page 4 - T h e D B - 9 S e r i a l P o r t; Figure 4.RS-232C Serial Port Pin Assignments; I n s t a l l a t i o n P r o c e d u r e; Follow these steps to connect the MIL-4711H to your network:; The voltage in use is visible.; The factory setting is 120VAC.; the network. Refer to the

Install Guide Model: MIL-4711H 4 T h e D B - 9 S e r i a l P o r t Figure 4.RS-232C Serial Port Pin Assignments Note: N/C=No Connect I n s t a l l a t i o n P r o c e d u r e Follow these steps to connect the MIL-4711H to your network: 1. Remove the MIL-4700H, power adapter, and cord from its shippi...