Dialogic DM/IP601-CPCI-100BT - Manual

Dialogic

®

DM/IP601-CPCI-100BT

IP Board

Quick Install Card

Part number 64-0027-02

Copyright © 2002-2007

Dialogic Corporation.

All Rights Reserved.

Before You Begin

Protecting the Board from Damage

CAUTION:

All computer boards are sensitive to

electrostatic discharge (“ESD”). Handle all static-sensitive
boards and components at a static-safe work area, and
observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions, visit

http://www.dialogic.com/support/hwinstall

to learn more.

Unpacking the Board

Unpack the Dialogic

®

DM/IP601-CPCI-100BT board

(“board”) according to the following steps:

1.

Prepare a static-safeguarded work area.

2.

Carefully remove the board from the shipping
carton and anti-static packaging. Handle the
board by the edges and avoid touching the board’s
components.

3.

Lay the board on the static-dissipative work
surface.

Note:

Place boards in static-shielding bags when carrying

boards from station to station.

CAUTION

: Do not remove the board from the anti-static

packaging until you are ready to install it. Observe proper
anti-static precautions at all times.

Installing the Hardware

NOTE

: In a Windows environment, install the software

first, the hardware second, and then run the Dialogic

®

Configuration Manager (DCM) to configure the system.

1.

Turn the power to the chassis

OFF

if you do not have a

live insertion system. If you do have live insertion
capability, the power to the chassis can remain

ON

.

2.

Remove the chassis cover plate or open the front door.

3.

Select an empty expansion bus slot.

NOTE

: When power is on, the Rear I/O module should be

installed first, before the main board.

4.

Install the Rear I/O module in the rear of the slot
selected in step 3. Use the slot’s board guides as you
insert the board into the chassis slot. Make sure that the
tabs on the board extractors engage the guide holes in
the chassis card cage, then lock down the board
extractors until the red locking tabs snap shut.

CAUTION

cPCI backplane pins are bent easily. Make sure that

the board is seated with hand pressure before fully

seating board. If board extractors are used to seat

the board, make sure to seat evenly.

5.

Install the board in the front of the slot selected in step 3.
Use the slot’s board guides as you insert the board into
the chassis slot. Make sure that the tabs on the board
extractors engage the guide holes in the chassis card
cage, then lock down the board extractors until the red
locking tabs snap shut.

NOTE:

If the power to the chassis is on, power is

automatically applied to the board, the Out of Service
LED lights briefly and then goes out, and the Power
LED goes on.

6.

Tighten the retaining screws to secure the board firmly
in the chassis slot (optional).

7.

Select a new slot and repeat steps 4-6 for each board you

Physical Description

RED

YEL

CARR

SGNL

LOOP

RED

YEL

CARR

SGNL

LOOP

A
L
A
R
M
S

T
A
T
U
S

RED

YEL

CARR

SGNL

LOOP

RED

YEL

CARR

SGNL

LOOP

A
L
A
R
M
S

S

A
T
U
S

P5

P4

P1

Board

Extractor

POWER

Alarm

Status

LEDs

OUT OF

SERVICE

Board

Extractor

Baseboard

Daughterboard

1

2

3

4

/

P 5

P 2

P 2

P 5

J 1 - J 4

R J - 4 8 C J a c k s

B N C C o n n e c t o r s

E t h e r n e t
I n t e r f a c e
C o n n e c t o r

E t h e r n e t
I n t e r f a c e
C o n n e c t o r

T r u n k 1

T r u n k 1

T r u n k 2

T r u n k 3

T r u n k 4

Faceplate

Compact PCI Board

T-1 and E-1 120-Ohm

E-1 75-Ohm

(front view)

Rear I/O Module

Rear I/O Module

Compact PCI Baseboard

Rear I/O Modules

Part:

Power LED

Red Alarm LEDs

Yellow Alarm LEDs

Carrier Signal LEDs

Loopback LEDs

Out of Service LED

Function:

Indicates board is powered up.

Not functional in this assembly.

Not functional in this assembly.

Not functional in this assembly.

Not functional in this assembly.

Indicates board is out of service
or in reset from host.

Part:

J1–J4

P2

P5

BNC
Connectors

Function:

Not functional in this assembly.

Telephony network interface test port

Rear I/O module connector to Compact PCI
backplane

Not functional in this assembly

P1, P4, P5

Compact PCI board connectors
to backplane.

Ethernet
Connector

Connection to Ethernet network

NOTES:

Rear I/O Modules are ordered separately and are available in two different forms depending

on the type of connectors used, guided or unguided. Select a Rear I/O Module that is
compatible with your chassis type. See the

PICMG 2.0 D3.0 Compact PCI

Specification

for

more information on guided and unguided connectors.