Dell 490-BCHD User Manual - Free PDF Download

Page 5 - Contents

Contents Chapter 1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 7 - System Requirements; Recording Serial Numbers

Chapter 1 Getting Started Before you begin installing your new AMD FirePro™ S7000 graphics card (P/N: 102- C414xx-xx), please make sure you have the proper system requirements and have completed the required preinstallation tasks as outlined in this chapter. 1.1 System Requirements Table 1–1 AMD Fir...

Page 9 - Installation Overview

Chapter 2 Hardware and Software Installation This chapter details how to install your graphics accelerator in your system as well as where to download associated software and drivers. 2.1 Installation Overview Once you have determined that your system meets the minimum requirements, perform the foll...

Page 11 - Display Properties

b. Screw in the extension bracket firmly. Note: Graphics card and extension bracket may not be exactly as depicted. Figure 2–2 Extension Bracket Attached to Graphics Card 7. Align your AMD FirePro graphics card with the PCIe slot and press it in firmly until the card is fully seated. You may need to...

Page 12 - Installing Graphics Drivers and Software; AMD Automatic Application Detection and Configuration

2.3 Installing Graphics Drivers and Software To install or remove the drivers and software, you must be logged on as a user with administrator rights.Drivers and configuration software, which include the Control Center software application, are provided to both operate and take advantage of all the ...

Page 13 - Baseplate Connections; Connecting Displays

Chapter 3 Display Configuration This chapter describes how to configure displays. It also lists available display connections for your graphics accelerator. 3.1 Baseplate Connections The following figure shows the display connections available on your graphics accelerator. Note: Baseplate may not ap...

Page 15 - Control Center Overview

Chapter 4 Using the Control Center Software 4.1 Control Center Overview The Control Center software application contains settings for configuring and fine- tuning your AMD product. Use it to manage desktops and displays, optimize your graphics processor for enhanced 3D application and video quality,...

Page 17 - Workstation Card Troubleshooting

Chapter 5 Reference This chapter provides notices, troubleshooting tips, and customer care, warranty, and standards-compliance information. 5.1 Workstation Card Troubleshooting The following troubleshooting tips may help if you experience problems.More troubleshooting information can be found using ...

Page 19 - Workstation Customer Care

5.1.6 There are bus address or interrupt conflicts. Make sure that the I/O and memory addresses reserved for the graphics board are not used by other hardware devices. The integrated on-board VGA controller of your AMD FirePro card uses the following addresses (hex): • I/O Address: Standard VGA I/O:...

Page 22 - Workstation Warranty Service

5.3 Workstation Warranty Service For warranty service instructions visit http://support.amd.com/us/warranty/Pages/ SupportWarrantyServices.aspx or contact one of our Customer Service Representatives. 5.3.1 Shipping Before shipping any unit for repair, obtain an RMA number for warranty service.When s...

Page 23 - International Compliance Information; Class A; Class B

Unauthorized repairs to an AMD board level product will void the warranty offered by AMD. AMD reserves the right to refuse to service any product which has been altered, modified, or repaired by non-AMD service personnel. 5.4 International Compliance Information This section details the worldwide co...

Page 24 - For further compliance information:

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Re-orient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit differe...