Deeshe Deeshe-fan-W24 - User Manual

１８寸壁扇　１４５Ｘ２１０ＭＭ

1. Mark the desired hole locations by

using the wall bracket, and then

drill holes.

1. Adjust the desired speed by pull chain switch with 2 speeds control.

0 - stop 1 - low 2 - high

2. Tilt or down the fan head for changing air flow direction.

2. For concrete wall installation, after
drilling,insert the wall anchors and
tap them flush with the wall,
position the bracket and then screw
the two bolts into the anchors,

securely ataching to the wall.

3. For wall stud installation, after drilling
the smaller diameter pilot hole,

position the bracket and screw the

two bolts into the wall until they are
secured.

CAUTION:THE FAN IS ONLY
SUITABLE FOR CONCRETE WALL
AND WALL STUD.DO NOT USE

FOR DRY WALL MOUNTING.USE

THE MOUNTING ACCESSORIES
SHIPPED WITH PRODUCTS FOR
WALL MOUNTING.

24

"

HIGH VELOCITY WALL FAN

1

2

3

4

5

Unplug the appliance before cleaning. Don’t use any water for cleaning metal surfaces.
Slightly moisten a cloth and then wipe off the surfaces of the fan. In order to remove
dust from the grill, use a vacuum cleaner or remove the front grill by removing the
securing screws on the edge of the grill. After cleaning, remount the grill. After doing
this, fasten the screws on the edge of the grill.

CARE AND MAINTENANCE

The manufacturer warrants this product to be free from manufacturing defects in the
material and workmanship under normal use for a period of one year after the date of
purchase by the original purchaser.
This warranty does not cover transit damages. This warranty does not apply to damages
from accident, misuse, alteration of any kind to the fan or where the connected voltage
is more than above the nameplate voltage. This warranty does not apply to the finish on
any portion of the product. Servicing performed by unauthorized persons shall render
the warranty invalid. The warranty is not responsible for damages of any kind, including
accident and consequential damages. Some states do not allow the exclusion or
limitation of the incidental or consequential damages, so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.

1-YEAR LIMITED WARRANTY

REPLACEMENT PARTS LIST

A

ITEM NO : FAN-W24

TECHNICAL SPECIFICATIONS

ITEM NO.

MODEL NO.

SIZE

VOLTE/Hz

CURRENT(A)

CFM

RPM

FAN-W24

SFWE-600.11.76

24

120V/60Hz

2.1A

1050

9000

A

24

Blade

FAN-W24-01

SIZE PART

DESCRIPTION

PART #

Warning:

U s e o f s e c o n d a r y s a f e t y s u p p o r t c a b l e d o e s n o t
guarantee protection against injury of persons. Mounting
of both the circulator and cable could fail if subject
to abuse, neglect or if improperly installed. To avoid
personal injury, circulators must be supported anytime
angle is adjusted.

PARTS

SPECIFICATION

QTY

Φ

3*3050

M5*13

ST8*50

1

1

2

1

1

Φ

8*

Φ

24*

δ

2

Φ

10*60

1. Loop one end of the cable around the large diameter
wires of both the front and rear guard as shown below.
Attach a cable retainer with the “U” on the tail side of the
loop leaving a tail of approximately 1 to 2 inches. Tighten
clamp nuts forming a tight loop, 32in. lbs of torque.
Make sure the cable does not interfere with the propeller.

Top Of
Circulator
Guards

1-2” Tail

Large
Guard
Wires

Tight Loop in Cable

2. Wrap the other end of the cable around a secure
building joist, beam, truss or other support near the fan
as shown below. Take up all excess slack in the cable. If
the fan is an oscillating model and wall mounted, leave
enough slack to allow free movement through range of
motion.

Installation -- Secondary

Safety Support Cable

3 . A t t a ch t h e r e m a i n i n g c a b l e r e t a i n e r s a s d o n e
previously in “step 1”. The excess tail should be trimmed
to extend 1 to 2 inches past the second clamp.

4. Check the assembly to assure the propeller is free of
all obstructions and turns freely.

5. Connect the circulator to the proper power supply
ensuring that it conforms to the electrical rating listed on
the circulator’s motor nameplate.

For concrete wall installation

1. Drill a hole in concrete wall,
insert the wall anchor and tap

wall.

2. Fasten a blot and a washer
through the terminal of
secondary safety support
cable into the anchor for
security.

ASSEMBLY INSTRUCTION

OPERATION INSTRUCTION

READ & SAVE THESE INSTRUCTIONS

Questions, problems, missing parts? Before returning the product,

please e-mail our customer service by

[email protected]

To prevent serious injury or property damage, read and understand owner's
manual before operating.

1. Unplug the fan before moving it or performing maintenance.
Don't operate the fan when your hands are wet.
2. Do not disassemble, repair or rebuild the fan.
3. Unplug the fan when it is not in use.
4. Do not unplug the fan by holding the cable cord. Unplug by holding the
plug.
5. DO NOT use the fan when there is damage to the cable cord or plug. If
the supply cord is damaged, it has to be replaced by the manufacturer,
its service agent or similarly qualified persons.
6. To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Do Not
Use Replacement Parts That Have Not Been Recommended By The
Manufacturer (e.g. Parts Made At Home Using A 3D Printer).
7. Do not use the fan close to fires.
8. Do not insert your hand or other objects into the guard or near movable
parts.
9. To reduce the risk of fire or electric shock, do not use this fan with any
solid-state speed control device.
10.

DO NOT use this fan outdoors, this fan is designed for indoor use only.

11. To Reduce The Risk Of Fire Or Electric Shock Do Not Use With An Extension Cord.

1. Unplug the fan from the socket and clean it with a soft cloth.
2. DO NOT immerse the fan.
3. Fit the guard onto fan before starting up the fan.
4. This fan is not intended for use by people (including children) with reduced physical,
sensory or mental capabilities or lack of experience and knowledge unless they have
been given supervisionor or instruction concerning use of the fan by a person responsible
for their safety. Supervise children to ensure they do not play with the fan.