Page 2 - ASHING MACHINE; Co; THE REPAIR METHOD OF GEAR MECHANISM FOR CLUTCH
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER ...
Page 4 - STRUCTURE OF THE WASHING MACHINE; Accessories
2. STRUCTURE OF THE WASHING MACHINE 3 STRUCTURE • GROUND WIRE In case of 3-wire power cord, ground wire will not be provided • POWER CORD • LINT FILTER • COLD WATER TAP After using the washer, close the water tap • DETERGENT CASE • PULSATOR • POWER SWITCH • CONTROL PANEL • BLEACH INLET • HOT WATER T...
Page 5 - DIRECTIONS FOR INSTALLATION AND USE; INSTALLATION OF THE UNDER BASE COVER [OPTION]; INSTALLING PLACE; Never install in these
3. DIRECTIONS FOR INSTALLATION AND USE 4 DIRECTIONS The openings must notbe obstructed by carpet-ing when the washingmachine is installed on acarpeted floor. INSTALLATION OF THE UNDER BASE COVER [OPTION] HOW TO INSTALL ON AN INCLINED PLACE ● The place where it would be exposed to direct sunlight. ● ...
Page 6 - HOW TO CONNECT THE INLET HOSE
5 CONNECTION FOR ORDINARY TAP 6 Connect the inlet hose adapterof the hose to the water inlet ofthe washer by turning it clock-wise to be fixed tightly. • Please check the rubber packing inside the inlet hose adapter ofthe hose. 1 Pull down the collarof the inlet hose toseparate it from thewater tap ...
Page 7 - HOW TO CLEAN THE FILTER
6 CONVENIENCE HOW TO CLEAN THE FILTER 4 Remove the dirtfrom the inlet filterwith a brush. 1 Pull the power plugout beforecleaning it. 2 Turn off thewater supply to the washerand sperate theinlet hose. 3 Pull the inlet filter out. CLEANING THE LINT FILTER • This washer has two type of Lint Filter in ...
Page 9 - FEATURE AND TECHNICAL EXPLANATION; WASH DRAIN SPIN FILL RINSE 1 DRAIN SPIN FILL RINSE 2 DRAIN •••; FEATURE OF THE WASHING MACHINE; WATER CURRENT TO ADJUST THE UNBALANCED LOAD; FUNCTION FOR SOAK WASH; AUTOMATIC WATER SUPPLY SYSTEM FOR BLANKET WASH
4. FEATURE AND TECHNICAL EXPLANATION 8 FEATURE WASH DRAIN SPIN FILL RINSE 1 DRAIN SPIN FILL RINSE 2 DRAIN ••• MOTOR C.W SINGAL C.C.W TIME(SEC.) 0.3 0.3 0.3 0.3 0.3 0.3 • • • • • • • 35 SEC. (About 29 Times) FILL WASH STOP WASH STOP • 30” 2’ 30” 2’ SOAK PROCESS MAIN PROCESS 60 Minute FEATURE OF THE W...
Page 10 - FUNCTIONAL PRINCIPLE OF BUBBLE WASHING MACHINE; AUTOMATIC DRAINNING TIME ADJUSTMENT
9 FEATURE FUNCTIONAL PRINCIPLE 1 The micom can remember the time from the begining of drain to reset point when the pressure switch reaches to “OFF” point 2 In case of continuous draining, residual drain time is determined by micom. Draining time as a whole = D + 90 Residual drain time.The time reme...
Page 11 - AUTOMATIC UNBALANCE ADJUSTMENT
Contact of safety switch Lid closing Lid opening Contact lever A Normal (ON) Position ofunbalanced load (OFF) AUTOMATIC UNBALANCE ADJUSTMENT CIRCULATING-WATER COURSE AND LINT FILTER The alarm finished when you close the lid after openingit. Check the unbalance of the wash load and the instal-lation ...
Page 12 - LINT FILTER
11 FEATURE Much lint may be obtained according to the kind ofclothes to be washed and some of the lint may alsosticks to the clothes.To minimize this possibility a lint filter is provided onthe upper part of the tub to filter the wash water as itis discharged from the water channel. It is good touse...
Page 13 - GEAR MECHANISM ASS’Y
12 FEATURE The proper water currents is made by the rotation of pulsator at a low speed to prevent the damage to the smallsized clothes. Planetary gear Sun gear Internal gear Pulsator 1 revolution 5 revolutions Gear pulley V-belt Gear unit as Motor Motor 1800 r.p.m (60Hz) 1500 r.p.m (50Hz) Gear Unit...
Page 14 - DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT; GEAR MECHANISM ASS’Y REPLACEMENT; Warning
5. DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT 13 DIRECTIONS GEAR MECHANISM ASS’Y REPLACEMENT BEFORE ATTEMPTING TO SERVICE OR ADJUST ANY PART OF THE WASHING MACHINE, DISCONNECT THE POWER CORD FROM THE ELECTRIC OUTLET. Warning 1 Raise the top plate on the outer cabinet. 2 Loosen four screws mounting ou...
Page 17 - THE REPAIR METHOD OF GEAR MECHANISM FOR CLUTCH SPRING PROBLEM; ALTERNATIVE TOOL FOR REPLACING THE CLUTCH BOSS ASSEMBLE; THE STRUCTURE OF GEAR MECHANISM
6. THE REPAIR METHOD OF GEAR MECHANISM FOR CLUTCH SPRING PROBLEM 16 THE REPAIR ALTERNATIVE TOOL FOR REPLACING THE CLUTCH BOSS ASSEMBLE Tool name Specification Q’ty Fixing jig 1 Ratchet handle 1 Socket and extension bar socket : 10mm, 17mm per each Some cotton yarn some THE STRUCTURE OF GEAR MECHANIS...
Page 18 - PROBLEM; HOW TO CHECK THE CLUTCH SPRING PROBLEM
17 THE REPAIR NO. PARTS NAME SPECIFICATION CODE Q’TY 1 CLUTCH SPRING 1.5*1.5 3615110000 1 2 CLUTCH BOSS PP 3619301300 1 3 GREASE beacon#325 3g PACKING PACKING THE CLUTCH BOSS ASS’Y 1 METHOD BY USING VINYL PACK PROBLEM 1) THE LAUNDARY IS IN THE SPIN TUB UNEVENLY WHEN JUST STARTING SPIN PROCESS. 2) TH...
Page 19 - Process; Disassemble 1; THE PROCESS OF DISASSEMBLE
18 THE REPAIR No. Process Notice Disassemble 1 1 2 3 4 Release screws marked 4-point Remove the protector Remove the v-belt Loosen the fastening nut Disassemble the spring washer Use wrench or driver- ratchet handle- extension bar- socket : 10mm Use fixing jig for pulley as to see fig 1.and 17mm-soc...
Page 20 - Disassemble 2
19 THE REPAIR No. Process Notice Disassemble 2 5 6 7 8 Disassemble the pulley Disassemble the clutch boss assembly Separate coupling from clutch boss ass’y Cleaning Catch the boss and pullupward with spiral rotate in the clockwise direction Clean the drum plate, couplingsurface and contact facebetwe...
Page 21 - Assemble 1; THE PROCESS OF ASSEMBLE
20 THE REPAIR No. Process Notice Assemble 1 1 2 3 4 Assemble the coupling Assemble the new clutch bossass’y Assemble the pulley Assemble the spring washer Check the uneven face of cou-pling is assembled upward - Push in the clutch boss ass’y with rotating on the clockwisedirection. - After assemblin...
Page 22 - Assemble 2
21 THE REPAIR No. Process Notice Assemble 2 5 6 7 8 Assemble the fastening nut Assemble the Belt Assemble the protector Final checking - Use fixing jig and 17mm socket wrench as if disas-sembling, as fastening torqueabout 100~200kgf-cm. - Check the end-play, up and downward and check thebinding forc...
Page 24 - TROUBLE SHOOTING GUIDE; CONCERNING WATER SUPPLY
7. TROUBLE SHOOTING GUIDE 23 TROUBLE SHOOTING PROBLEM WATER IS NOT SUPPLIED. CHECK POINT Do you open the water tap? Is the filter of the water inlet valve clogged with dirt? Is the water pressure sufficient? (0.3~8 kgf/cm 2 ) Does the water inlet valve make operating sound? Is the connector or the t...
Page 25 - CONCERNING WASHING
PROBLEM WATER SUPPLY IS NOT STOPPED. CHECK POINT Does the water supplycontinue while the poweris turned off? Does the water supply startas soon as you press thepower switch? Operate the washer aftersetting the water level to“HIGH” Does the water supplycontinue after the waterreaches to the “HIGH”lev...
Page 26 - CONCERNING DRAINING
25 TROUBLE SHOOTING PROBLEM THE WASHER DOES NOT DRAIN. CHECK POINT Do you install thedrain hose proper-ly? Is the foreign matteraccumulated insidethe pump housing? Is the output voltage ofthe drain pump nor-mal? CAUSE SOLUTION Install the drain hoseproperly. Remove the foreign mat-ter from the pump ...
Page 27 - YES; CONCERNING SPINNING
26 TROUBLE SHOOTING PROBLEM THE WASHER DOES NOT SPIN. CHECK POINT Is the lid open? Does the door switchoperate normally? Does the safety switchoperate normally? Does the pulsator rotatewhile the tub does notrotate? Is the connector ofP.C.B ASS‘Y connectedproperly? Is the input voltage of the drainmo...
Page 28 - CONCERNING OPERATION
27 TROUBLE SHOOTING NO NO NO PROBLEM THE INDICATOR LAMPS(L.E.D) DO NOT LIGHT UP WHEN THE POWER BUTTON IS PRESSED. PROGRESS LAMPS(LED) DO NOT LIGHT UP. MOTOR ROTATES WHEN START/HOLD BUTTON IS NOT PRESSED. ABNORMAL NOISE DURING WASH PROCESS. CHECK POINT Is the plug connect-edto electric outlet? Is the...
Page 29 - CONCERNING ERROR MESSAGE
28 PCB ASS’Y MESSAGE CAUSE SOLUTION Improper installation of drain hose. The drain hose is blocked up by foreign matter. Drain motor is inferior. The water tap is closed. The water inlet filter clogged. It passes over the 60 minutes, yet it doesn’t come to assigned water level. Wash loads get uneven...
Page 30 - APPENDIX; WIRING DIAGRAM; SYMBOL
APPENDIX 29 PCB ASS’Y WIRING DIAGRAM [NON PUMP] WIRING DIAGRAM F-PCB M-PCB SYMBOL FUSE A FUSE B 250V/8A 600mA 250V/5A 315mA RATING(V) 110-127V 220-240V * RATING: REFER TO RATING PLATE AC SOURCE BK or BR WH or BL GN or GN/YW FUSE A BL/YW WH BK BL WH/RD WH/RD WH/RD WH/RD WH RD/BL YW/BK GN/WH BK/WH BR ...
Page 33 - PARTS DIAGRAM
Page 36 - PARTS LIST; PART NAME; Caution
35 PARTS DIAGRAM PARTS LIST NO. PART NAME PARTCORD SPECIFICATION Q’TY NOTE A01 PLATE T 3614519300 PP 1 A02 NOZZLE DETERGENT 3618102400 PP 1 A03 CASE DETERGENT 3611119600 PP 1 A04 DOOR B AS 361A100800 ABS 1 A05 DOOR F AS 361A100700 ABS 1 A06 SPRING 3615111210 DWF-850M, D=2.0 1 A07 HINGE DOOR 36129024...
Page 39 - CIRCUIT DIAGRAM
