Page 2 - Manual Revisions; Preface
ENGLISH 2 D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corp...
Page 3 - Table of Contents
ENGLISH 3 Table of Contents Preface ............................................................................................. 2 Manual Revisions .......................................................................................... 2 Trademarks ..................................................
Page 4 - Safety Instructions; Safety Cautions
ENGLISH 4 To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the following precautions. Observe and follow service markings. Do not service any product except as explained in your system documentation. Opening or removing covers that are marked with the...
Page 6 - Protecting Against Electrostatic Discharge
ENGLISH 6 Static electricity can harm delicate components inside your system. To prevent static damage, discharge static electricity from your body before you touch any of the electronic components, such as the microprocessor. You can do so by periodically touching an unpainted metal surface on the ...
Page 7 - Product Overview; Setup; Package Contents
ENGLISH 7 Product Overview Setup The setup of the DGS-1005G can be performed using the following steps: • The power outlet should be within 1.82 meters (6 feet) of the Switch. • Visually inspect the DC power jack and make sure that it is fully secured to the power adapter. • Do not cover the ventila...
Page 10 - Features
ENGLISH 10 Features The DGS-1005G 5-port 10/100/1000BASE-T Gigabit Ethernet Switch was designed for easy installation and high performance in an environment where traffic on the network and the number of users increase continuously. • Five (5) 10/100/1000BASE-T Gigabit Ethernet ports• Supports Auto-...
Page 11 - Hardware Overview
ENGLISH 11 Hardware Overview Top Panel (LEDs) The LED indicators of the Switch include Power and Speed/Link/Act. The following shows the LED indicators for the Switch along with an explanation of each indicator (refer to the next page).
Page 14 - Installation; Before You Connect to the Network
ENGLISH 14 Installation This section will explain how to connect Ethernet devices to your new D-Link switch and how to mount the switch. Before You Connect to the Network The site where you install the Switch may greatly affect its performance. Please follow these guidelines for setting up the Switc...
Page 15 - Mounting the Switch on the Wall
ENGLISH 15 Mounting the Switch on the Wall The DGS-1005G can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: Mounting on a ceme...
Page 16 - Connecting the Switch
ENGLISH 16 Connecting the Switch DGS-1005G to End Node End nodes include PCs outfitted with a 10, 100, or 1000Mbps RJ-45 Ethernet Network Interface Card (NIC) and most routers. An end node can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable. The end node can be co...
Page 17 - Troubleshooting
ENGLISH 17 Troubleshooting 1. Why can´t I share my Internet connection to multiple computers when using my D-Link switch? If you are connecting directly to a Cable or DSL modem, you will need a router to “share” your Internet connection or a computer using ICS (Internet Connection Sharing) or Proxy....
Page 18 - Networking Basics
ENGLISH 18 Networking Basics Check your IP address After you install your new D-Link adapter or if you already have an Ethernet adapter installed on your computer, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. router) automatically. To verify your IP ...
Page 19 - Statically Assign an IP address
ENGLISH 19 Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Change Adapter...
Page 20 - Glossary
ENGLISH 20 Glossary 1000BASE-LX A short laser wavelength on multimode fiber optic cable for a maximum length of 550 meters. 1000BASE-SX A long wavelength for a “long haul” fiber optic cable for a maximum length of 10 kilometers. 100BASE-FX 100Mbps Ethernet implementation over fiber. 100BASE-TX 100Mb...
Page 25 - Technical Specifications
ENGLISH 25 Standards • IEEE 802.3 10BASE-T Ethernet • IEEE 802.3u 100BASE-TX Fast Ethernet • IEEE 802.3ab 1000BASE-T Gigabit Ethernet • IEEE 802.3x Flow Control • IEEE 802.1p Priority Queuing Protocol • CSMA/CD Data Transfer Rate Ethernet: • 10Mbps (half-duplex) • 20Mbps (full-duplex) Fast Ethernet:...
Page 26 - RJ-45 Pin Specifications
ENGLISH 26 RJ-45 Pin Specifications The following table shows the standard RJ-45 receptacle/connector and their pin assignments. RJ-45 Connector pin assignment Contact Media Direct Interface Signal 1 Rx +(receive) 2 Rx - (receive) 3 Tx + (transmit) 4 Not used 5 Not used 6 Tx - (transmit) 7 Not used ...
Page 27 - Contacting Technical Support
ENGLISH 27 Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DGS-1005G) • Hardware Revision (located on the label o...
Page 28 - Registration
ENGLISH 28 Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Registration Version 1.1 May 18
