CyberPower CPS480PAU - Manual

This product package includes:

• AC Power Inverter

• Cigar Plug Cable

• Battery Clamp Cable (CPS480PAU only)

• User Guide

Thank you for choosing a CyberPower power inverter. To enjoy all the

features and benefits of Inverter, please read and follow all instructions

completely.

The power inverter is a portable source of 120 volt AC power. The AC

Power converts DC battery power from your vehicle into standard 120

volt AC power, allowing you to power most notebook computers, cell

phone chargers, camcorders, and other electronic products drawing AC

power. Your personal devices may exceed the inverters wattage limit.

Refer to your device's user guide for actual wattage requirements.

This guide contains important information regarding the safety,

operation, maintenance, and storage of this product. Failure to read this

guide and follow the directions could result in injury and/or property

damage.

Before installing and using the CyberPower power inverter please read

the manual. Misusing or incorrectly connecting the Inverter may damage

the equipment or create hazardous conditions for users. Read the

following safety instructions and pay special attention to all

CAUTION

and

WARNING

statements in the manual.

1. 120 volt AC outlet

2. USB charging port

3. LED indicator light [Power LED(Green), Input / Output Fault (Red)]

4. ON/OFF Switch

5. DC Input positive terminal

6. DC Input negative terminal

7. Cooling Fan

Connecting the power cord for loads under 150 watts

Follow these steps to connect the power inverter :

1. Place the inverter on a flat surface in your vehicle floor.

2. Make sure the power switch on the panel is off.

3. Take the power cord equipped with the cigar plug and place the ring

terminals over the two cabling terminals on the back of the inverter.

4. Place the inverter cigar plug in the vehicle cigarette lighter socket.

5. Turn on the power switch. The green light indicates that the inverter is

operating normally and that AC power is available at the outlet.

6. Verify that the connected device(s) draws less than 150 watts and plug

into the AC outlet.

7. Always turn the inverter off when not in use.

Connecting the power cords for loads over 150 watts

Follow these steps to connect the power inverter :

1. Place the inverter on a flat surface.

2. Make sure the power switch on the panel is off.

3. Take the power cord equipped with battery clamps on one end and

place the ring terminals over the two cabling terminals on the back of

the inverter.

4. Fasten the positive (red) clamp to the positive battery post, and then

fasten the negative (black) clamp to the negative battery post.

5. Turn on the power switch. The green light indicates that the inverter is

operating normally and that AC power is available at the outlet.

6. Take device power cord plug into the inverter AC outlet.

7. Always turn the inverter off when not in use.

Make sure you connect cable red to red and black to black, and make

sure you screw the nuts on tightly.

Use the cigar plug cable only when the vehicle’s engine is running.

Use the cigar plug cable with the engine off will cause excessive

battery drain.

• Do not operate the inverter near flammable materials, fumes, or

gases.

• Always use the inverter where there is adequate ventilation. Do not

obstruct the ventilation slots.

• Never immerse the unit in water or other liquids.

• Proper cooling is essential when operating the inverter. Refrain from

placing the inverter near the vehicle's heat vent or in direct sunlight.

• Always turn the inverter off by removing it from the DC accessory

socket when not in use.

• Check the warning labels on battery chargers or adapters before

connecting them to the inverter. Do not connect battery chargers or

adapters with warnings about using with inverters.

CAUTION :

1. Connect the RED cable to the

POSITIVE terminal of the battery.

2. Connect the BLACK cable to the

NEGATIVE terminal of the battery.

A reverse polarity connection (positive to negative) will blow a fuse in

the inverter and may permanently damage the unit. Damage caused

by a reverse polarity connection is not covered by your warranty.
Batteries contain corrosive materials and present an electrical shock

hazard. To prevent irritation and burns, wear protective eyewear and

clothing when you install the inverter or work with the batteries.Take

special care to ensure that metal tools and personal metal objects like

rings and bracelets do not contact the battery terminals.

CAUTION

WARNING

CAUTION

Battery

Red

Black

(+)

(-)

CAUTION :

1. Connect the RED cable to the

POSITIVE terminal of the inverter.

2. Connect the BLACK cable to the

NEGATIVE terminal of the inverter.

CPS240PAU

CPS480PAU

Front View

Back View

Front View

Back View

1

1

2 3

4

7

5

6

4

240 User Guide

480 User Guide

AC Mobile Power Inverters

Introduction

Product Overview

Package Contents

Product Features

Operation - CPS240PAU / CPS480PAU cigar plug cable

Operating and Storage Tips

Operation - CPS480PAU only

1

2

3

7

5

6

Operating Tips

The inverter should only be operated under the following conditions:

• Dry - Do not allow water or other liquids to come into contact with the

inverter.

• Moderate Temperature - Ambient air temperature should be between

32

o

F - 104

o

F (0

o

C - 40

o

C). Keep the inverter out of direct sunlight.

• Free Air Flow - Keep the inverter's ventilation slots unobstructed to

ensure air flow to the unit. Do not place any items on or over the inverter

during operation. The unit will shut down if it overheats.

Storage Tips

• Proper storage temperature range is 32

o

F - 122

o

F (0

o

C - 50

o

C)

• Store and use the inverter in a cool and dry environment.

• Avoid exposing the inverter to heating elements, direct sunlight, or high

humidity.

TM

TM

CPS240PAU

CPS480PAU