CyberPower CPS160PPB2U - Manual

160 User Guide

AC Mobile Power Inverter

CPS160PPB2U

Specifications

Troubleshooting

Fuse Replacement

Important Safety Information

Package Contents

Product Features

• AC Mobile Power Inverter

• User Guide

1. Unplug the inverter from the DC power outlet.

2. Disassemble the DC plug as pictured below.

3. Replace the 15 amp fuse.

4. Reassemble the DC plug as pictured below.

Input Voltage

11 to 15 volts

Output Peak Power

160 Watts

Output Continuous Power 100 Watts

Output Voltage

120 Volts / USB 5 Volts

Output Frequency

60 Hz

Output Waveform

Simulated Sine Wave

Protection Features

Low Voltage, Overheat,

Overload, Short Circuit

Problem

No AC output power

Poor contact with DC power

outlet.

Automotive electrical system

requires ignition to be on.

Car's DC power outlet fuse is

blown.
Over-heating.

Vehicle's battery voltage is

below 11 volts.
Vehicle's battery input voltage

is higher than 15 volts.
Inverter is overloaded.

Ensure the inverter is securely plugged

into vehicle's DC power outlet. Replace

the DC power outlet if necessary.
Turn the vehicle ignition to the

"Accessory" position.

Check the vehicle fuse panel and

replace the damaged fuse.
Allow inverter to cool. Ensure that there

is adequate ventilation around the unit

and load does not exceed the unit's

Continuous Power rating (see

specifications).
Unplug the inverter and start the vehicle

to charge the battery.
Check your vehicle's user guide for

troubleshooting.
Ensure load does not exceed the unit's

Continuous Power rating (see

specifications).

Suggested Solutions

Possible Cause

Before installing and using the CyberPower Mobile Power Inverter

please read and follow these safety instructions:

• Moderate Temperature - Ambient air temperature should be between

32

o

F - 104

o

F (0

o

C - 40

o

C). Keep the inverter out of direct sunlight.

• Free Air Flow - Keep the inverter's ventilation slots unobstructed to ensure

air flow to the unit. Do not place any items on or over the inverter during

operation. The unit will shut down if it overheats.
Storage Tips

• Proper storage temperature range is 32

o

F - 122

o

F (0

o

C - 50

o

C)

• Store and use the inverter in a cool and dry environment.

• Avoid exposing the inverter to heating elements, direct sunlight, or high

humidity.

Operating and Storage Tips

Operating Tips

The inverter should only be operated under the following conditions:
• Dry - Do not allow water or other liquids to come into contact with the

inverter.

• Do not operate the CPS160PPB2U near flammable materials, fumes, or

gases.

• Always use the inverter where there is adequate ventilation. Do not

obstruct the ventilation slots.

• Never immerse the unit in water.

• Proper cooling is essential when operating the inverter. Refrain from

placing the inverter near the vehicle's heat vent, or in direct sunlight.

• Always turn the inverter off when not in use by removing it from the DC

accessory socket.

• Check the warning labels on battery chargers or adapters before

connecting them to the inverter. Do not connect battery chargers or

adapters with warnings about using with inverters.

CyberPower Systems (USA), Inc.

4241 12th Av enue Eas t, Suite 400, Shak opee, MN 55379

TEL: (952) 403-9500 Toll-Free: (877) 297-6937

FAX: (952) 403-0009 E-mail: s ales @c ps ww.c om

CPSww.com

C

2014 CyberPower Systems, Inc.

All rights reserved. Reproduction in whole or in part without permission is prohibited.

K01-0000378-01

Limited Warranty

Product Registration

Technical Support

Legal notices (FCC Part 15)

CyberPower warrants this CPS160PPB2U (the "Inverter") to be free from material

and manufacturing defects for two years. If a defect results in product failure during its

normal use, CyberPower’s sole responsibility is to repair or replace (at its sole option)

the Inverter.

The foregoing Limited Warranty is the consumer’s sole and exclusive remedy and

excludes any incidental or consequential damages. Some States do not allow the

exclusion or limitation of incidental and consequential damages, so certain of the

above limitations or exclusions may not apply to you (the Consumer). This limited

warranty gives the Consumer specific legal rights and the Consumer may have other

rights, which vary from State to State.

To make a Limited Warranty claim:

1. Pack and ship the Inverter to CyberPower at 4241 12th Avenue East, Suite 400,

Shakopee, MN 55379.

2. Clearly indicate on the outside of the packaging that this is a “WARRANTY

RETURN”

3. Clearly include your name and address (a) on the outside packaging and (b) on a

sheet of paper enclosed in the box with the Inverter that is being returned.

4. You MUST prepay all shipping costs and you are responsible for packaging and

shipment.

CAUTION:

Any changes or modifications not expressly approved by the guarantee

of this device could void the user’s authority to operate the equipment.

Thank you for purchasing a CyberPower product. Prompt product registration entitles

coverage under the Limited Warranty and also allows the opportunity to be notified of

product enhancements, upgrades, and other announcements.

Registration is quick and easy at www.cpsww.com/register

Feel free to contact our Tech Support department with installation, troubleshooting, or

general product questions.

CyberPower Technical Support

Phone: 1-877-297-6937

Email: [email protected]

Web: www.CPSww.com

Address: 4241 12th Ave. E., STE 400, Shakopee, MN 55379

Hours of Operation: Monday – Friday, 7:00am – 6:00pm (CST)

This equipment has been tested and found to comply with the limits for a Class B Digital Device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the

equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for

help. Any special accessories needed for compliance must be specified in the instruction.

CAUTION:

A shielded-type power cord is required in order to meet FCC emission limits and

also to prevent interference to the nearby radio and television reception. It is essential that only the

supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment.

Spring

Ring

Contact Pin

Contact Retainer

15A Fuse

Power plug

1. 12V power plug
2. USB charging ports
(2.1 AMPS)
3. Cooling Fan
4. 120V AC outlet
5. Seat clip
6. Child safety covers

1

2

6

3

4

5

TM