Cub Cadet BV 228- User Manual
Cub Cadet BV 228– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – SAVE THESE INSTRUCTIONS; SERVICE INFORMATION
- Page 3 – OIL AND FUEL INFORMATION
- Page 4 – TROUBLESHOOTING; CLEANING AND STORAGE; OPERATING INSTRUCTIONS; OPTIONAL ACCESSORY
- Page 5 – 69-07543 P00; Souffleur / aspirateur à; L’APPAREIL NE DÉMARRE PAS ?; li; Manuel de l’utilisateur
- Page 6 – CONSERVEZ CES INSTRUCTIONS; SERVICE TECHNIQUE; CONSIGNES DE SÉCURITÉ
- Page 7 – INSTRUCTIONS DE DÉMARRAGE ET D’ARRÊT; SI VOUS UTILISEZ LE DÉMARREUR ÉLECTRIQUE ELECTRIC STARTER; INFORMATIONS SUR L’HUILE ET LE CARBURANT
- Page 8 – ENTRETIEN ET RÉPARATIONS; INSTRUCTIONS D’UTILISATION
- Page 9 – RÉSOLUTION DES PROBLÈMES; NETTOYAGE ET RANGEMENT; FONCTIONNALITÉS DÉMARREUR ÉLECTRIQUE ET POWER START BITTM; ACCESSOIRE EN OPTION
- Page 10 – REMARQUES
- Page 11 – Sopladora / Aspiradora manual; Se necesitan herramientas:; Manual del Operador
- Page 12 – GUARDE ESTAS INSTRUCCIONES; INFORMACIÓN DE SEGURIDAD
- Page 13 – INSTRUCCIONES DE ARRANQUE Y PARADA; SI UTILIZA EL ARRANCADOR ELÉCTRICO; INFORMACIÓN DEL ACEITE Y COMBUSTIBLE
- Page 14 – INSTRUCCIONES DE MANTENIMIENTO Y REPARACIÓN; INSTRUCCIONES DE OPERACIÓN
- Page 15 – Almacenamiento a largo plazo; LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS; LIMPIEZA Y ALMACENAMIENTO; ACCESORIO OPCIONAL
- Page 16 – HOW TO OBTAIN SERVICE:; Le Droit des États vis à vis de la présente garantie:; CÓMO OBTENER SERVICIO:; CUB CADET LLC
769-07543 P00
01/12
NEED HELP?
CALL 1-877-282-8684 IN U.S. OR 1–800–668–1238 IN CANADA
BV228 EC
2-Cycle
Electric Start Capable
Handheld Blower / Vacuum
IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
9
Upper Blower Tube
Removing Unit From Carton
Assemble The Unit
Insert the upper blower
tube into the blower outlet
and turn it clockwise until
it locks into place.
Install the lower blower tube
onto the upper blower tube
and turn it clockwise until it
locks into place.
Starting The Unit
Assemble The Unit
Place the unit on a level
surface. Fill the fuel tank.
Crouch in the starting
position.
Squeeze and hold
the
throttle for all further steps.
Pull
the rope
5 times
.
Move
the choke lever to
Position 2
.
1
1
2
Remove all contents from
carton.
5
1
8
3
Starting The Unit
10
11
Need Help?
Call 1-877-282-8684
DIDN’T START?
Repeat the starting instructions.
IF
engine fails to start after 2 attempts,
move choke lever to position 3 and pull
the starter rope until engine starts
IF
unit still fails to start, refer to the
operator’s manual for additional starting
and troubleshooting information
Mix thoroughly in a separate
fuel can:
– 2.6 fl. oz. of 2-cycle
engine oil
– 1 gallon of unleaded
gasoline
NOTE:
Do not mix directly in
the fuel tank.
4
Starter Rope
On/Off Stop Control
Lower Blower Tube
Trigger
Handle
Cruise Control
Starting The Unit
Fuel Cap
Primer Bulb
Choke Lever
Lower Vacuum Tube
Upper Vacuum Tube
Vacuum Elbow
Vacuum Bag Strap
Cinch Strap
Vacuum Bag
Zipper
Air Filter
Cover
Muffler
Cover
Spark Plug
Tools Required:
• Flathead Screwdriver
1 Gallon
2.6 oz
50:1
Press
the primer bulb
10
times
, or until fuel is visible.
Move
the choke lever to
Position 1
.
1
6
7
5 X
Continue to squeeze
the
trigger, or press down the
cruise control, and allow the
unit to warm up for 30-60
seconds.
Continue to squeeze the
trigger.
Move
the choke
lever to
Position 3
.
Warm
the unit for an
additional 60
seconds
. The unit may be
used during this time.
14
Continue to squeeze the
trigger. Pull
the rope
3-5
times
to start the engine.
12
3-5 X
1
13
10 X
Primer
Bulb
Choke Lever
E
s
p
a
ñ
o
l
—
P
a
g
e
1
1
E
n
g
li
s
h
—
P
a
g
e
1
F
ra
n
ç
a
is
—
P
a
g
e
5
Operator’s Manual
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
• Avoid accidental starting. Be in the starting position whenever pulling the starter rope. The operator and unit must be in a stable position while starting. Refer to Starting and Stopping Instructions . • Do not set unit on any surface except a clean, hard area while engine is running. Debris such...
3 ASSEMBLING THE UNIT BLOWER ASSEMBLYInstalling the Upper Blower Tube 1. Align the bump on the end of the upper blower tube with the bump slot on thebottom end of the blower outlet (Fig. 1). 2. Insert the upper blower tube into the blower outlet (Fig. 1). 3. Twist the upper blower tube clockwise unt...
REPLACING THE SPARK PLUG Use a replacement part number 753-06193 . The correct spark gap is 0.025 in. (0.635 mm) . 1. Stop the engine and allow it to cool. 2. Grasp the plug boot firmly and pull the cap from the spark plug.3. Clean dirt from around the spark plug. Remove the spark plug from the cyli...
