Page 2 - 5 Volvo Drive
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. © 2003 Crestron Electronics, Inc.
Page 3 - Contents; Operations Guide – DOC. 5708A
Crestron ST-PC Dual AC Power Control Module Contents Dual AC Power Control Module: ST-PC 1 Introduction ............................................................................................................................... 1 Features and Functions ..............................................
Page 5 - Introduction; Features and Functions
Crestron ST-PC Dual AC Power Control Module Dual AC Power Control Module: ST-PC Introduction Features and Functions There are two Crestron ® Dual AC Power Control Module configurations available: ST-PC and STI-PC. Configuration is based on the type of power availability. Use the ST-PC with a 120V po...
Page 6 - Specifications; SPECIFICATION DETAILS; Dual AC Power Control Module: ST-PC Operations
Dual AC Power Control Module Crestron ST-PC AC power is supplied via a 3-wire line cord (no plug on the STI-PC configuration). This power is solely for the purpose of powering the loads attached to the POWER A and B ports. Specifications The following table provides a summary of specifications for t...
Page 7 - Physical Description
Crestron ST-PC Dual AC Power Control Module NOTE: Crestron software and any files on the website are for Authorized Crestron dealers and Crestron Authorized Independent Programmers (CAIP) only. New users may be required to register to obtain access to certain areas of the site (including the FTP sit...
Page 9 - Ports; PIN SIGNAL; GND
Crestron ST-PC Dual AC Power Control Module Ports A number of labeled ports are provided on the back of the ST-PC. Refer to the following illustrations and descriptions. ST-PC Ports CRESTRON ELECTRONICS INC. N.J. 07626 .5A 12VDC NET NET POWER A POWER IN POWER B 90-125VAC 10A MAX OUTPUT COMBINED 50-6...
Page 10 - POWER A and POWER B; NET
Dual AC Power Control Module Crestron ST-PC POWER A and POWER B For the ST-PC, two three-prong socket connectors are provided to connect to any device that requires AC on/off power switching. For the STI-PC, two international power cords (approximately six feet in length) are available for connectio...
Page 11 - Setup; Identity Code; Functions | Set Network ID; Set ID; Current Network Devices; Close; Hardware Hookup
Crestron ST-PC Dual AC Power Control Module Setup Identity Code Refer to the note on page 12 for a definition of Viewport. All equipment and user interfaces within the network require a unique identity code (Net ID). These codes are two-digit hexadecimal numbers from 03 to FE. The Net ID of each uni...
Page 13 - Programming Software; Earliest Version Software Requirements for the PC; NOTE
Crestron ST-PC Dual AC Power Control Module Programming Software NOTE: Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website ( www.crestron.com ). To post a question or view questions you have...
Page 14 - C2Net-Device Slot in Configuration Manager
Dual AC Power Control Module Crestron ST-PC Configuration Manager is where programmers “build” a Crestron control system by selecting hardware from the Device Library . In Configuration manager, drag the PRO2 from the Control Systems folder of the Device Library and drop it in the upper pane of the ...
Page 15 - Setting the Net ID in Device Settings; Net ID; SIMPL Windows automatically changes the Net ID values of a device
Crestron ST-PC Dual AC Power Control Module C2Net Device, Slot 9 Setting the Net ID in Device Settings Double-click the ST-PC icon to open the “Device Settings” window. This window displays the ST-PC device information. If necessary, select the Net ID tab to change the Net ID as shown in the followi...
Page 16 - ST-PC Symbol in Programming Manager; pwr; Device Extenders; Program View; Uploading
Dual AC Power Control Module Crestron ST-PC ST-PC Symbol in Programming Manager Programming Manager is where programmers “program” a Crestron control system by assigning signals to symbols. The following graphic shows the ST-PC symbol in the SIMPL Windows’ Programming Manager. ST-PC SIMPL Windows Sy...
Page 17 - Firmware for the ST-PC is not field upgradable.; Communication Settings; For laptops and other PCs without a built-in RS-232 port, Crestron
Crestron ST-PC Dual AC Power Control Module parameters, and communicate with network device consoles and touchpanels, among many other tasks. Viewport can function as a terminal emulator for generic file transfer. All of these functions are accessed through the commands and options inViewport menus....
Page 18 - Communications settings; as the connection type. Verify that an available COM port; OK; button to save the settings
Dual AC Power Control Module Crestron ST-PC 1. Open the Crestron Viewport. Either launch the standalone version of Viewport, or start SIMPL Windows, and from the menu bar, select Tools | Viewport . 2. Refer to the following illustration. From the Viewport menu, select Setup | Communications settings...
Page 19 - Uploading a SIMPL Windows Program; Upload via SIMPL Windows; What to Send
Crestron ST-PC Dual AC Power Control Module NOTE: The parameters shown in the illustration above are the port settings for a 2- Series control system. Consult the Operations Guide for the control system being used for the exact parameter selection. 4. To verify communication, select Diagnostics | Es...
Page 20 - Diagnostics | Report Program Information; . This should display a; Problem Solving; Troubleshooting; TROUBLE
Dual AC Power Control Module Crestron ST-PC “Send Program” Window 4. To verify that the program has been transferred successfully, select Diagnostics | Report Program Information . This should display a window that provides details about the current program loaded into the control system. Problem So...
Page 21 - Further Inquiries; Check the Crestron website (
Crestron ST-PC Dual AC Power Control Module Further Inquiries If after reviewing this Operations Guide, you cannot locate specific information or have questions, please take advantage of the Crestron award winning customer service team by calling: • In the US and Canada, call the Crestron corporate ...
Page 22 - Return and Warranty Policies; Merchandise Returns / Repair Service
Dual AC Power Control Module Crestron ST-PC Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and reques...
Page 23 - This page intentionally left blank.
Crestron ST-PC Dual AC Power Control Module Operations Guide – DOC. 5708A Dual AC Power Control Module: ST-PC • 19 This page intentionally left blank.
Page 24 - Operations Guide
Crestron Electronics, Inc. Operations Guide – DOC. 5708A 15 Volvo Drive Rockleigh, NJ 07647 11.03 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
