Page 2 - 5 Volvo Drive
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON
Page 3 - Contents
Crestron CP2/CP2E 2-Series Integrated Control Processor Contents 2-Series Integrated Control Processor: CP2/CP2E 1 Introduction ............................................................................................................................... 1 Features and Functions ......................
Page 5 - Introduction; Features and Functions; Functional Summary
Crestron CP2/CP2E 2-Series Integrated Control Processor 2-Series Integrated Control Processor: CP2/CP2E Introduction Features and Functions Crestron’s CP2 and CP2E 2-Series Integrated Control Processors, cost-competitive options in Crestron's 2-Series line of integrated control systems, are designed...
Page 6 - bit Motorola ColdFire; Specifications; CP2/CP2E 2-Series Integrated Control System Specifications; SPECIFICATION DETAILS
2-Series Integrated Control Processor Crestron CP2/CP2E bit Motorola ColdFire processor. The 2-Series operating system is vastly upgraded from Crestron’s X-generation products, yet compatible with existing Crestron software and programming. A key feature is the new Crestron Compiler, which allows ...
Page 7 - Physical Description; Front and Rear Panels; The front panels of the CP2 and CP2E are shown below.; CP2/CP2E Front Panels
Crestron CP2/CP2E 2-Series Integrated Control Processor Physical Description The CP2/CP2E integrated control systems are housed in black enclosures with labeling on the front and rear panels. The front panels of both units include standard LEDs and two reset buttons. All connections to the units are...
Page 8 - Controls and Indicators; Pressing this button in combination with the; Ports; The CP2/CP2E rear panel ports are illustrated and described below.
2-Series Integrated Control Processor Crestron CP2/CP2E Controls and Indicators The CP2/CP2E front panel indicators and controls are described below. PWR (Power) This LED illuminates when the unit is connected to and receives 24VDC power from an AC power pack or the Cresnet NET connector. NET This L...
Page 9 - not; be used. Only the required pins for each communication type should; Non-Standard COM Pinout; PIN
Crestron CP2/CP2E 2-Series Integrated Control Processor NOTE: The orientation of this connector is “upside down” compared to other Crestron network devices (e.g., CNX-BIPAD8, CNX-RMCLV). Be sure the mating Cresnet cable connector is properly aligned before attempting to insert it, to avoid damage to...
Page 10 - COM Pinout to RS-485 Bus; INFRARED – SERIAL OUTPUT; RELAY OUTPUT
2-Series Integrated Control Processor Crestron CP2/CP2E COM Pinout to RS-485 Bus COM (DB9) CONNECTOR RS-485 BUS Tie Pins 1 & 9 - Tie Pins 4 & 6 + Pin 5 G INFRARED – SERIAL OUTPUT A B C D E F G H S G S G S G S G INFRARED - SERIAL OUTPUT S G S G S G S G These connectors provide eight serial ou...
Page 11 - LAN Port Pinout; TYPE PIN; NOTE; ports are provided with the unit.; Memory
Crestron CP2/CP2E 2-Series Integrated Control Processor 24VDC, 2.0A (Power Supply) 2 4 V D C 2.0A This male connector can be used to supply 24VDC power to the CP2/CP2E from an AC power pack purchased separately. (Refer to Optional Power Supply on page 13). When power is supplied to the units through...
Page 12 - Flash; TOP LEVEL SECONDARY LEVEL; Viewport; ), to simplify restoring them in the event of file corruption or to; Volatile; Digital, analog and serial signal values
2-Series Integrated Control Processor Crestron CP2/CP2E series control engine. Non-volatile memory contains information that is retained after loss of electrical power. Volatile memory is lost after a power failure. Refer to the lists below for a breakdown of memory usage for program-related informa...
Page 13 - DRAM; Industry Compliance; To prevent bodily injury when mounting or servicing this unit in a
Crestron CP2/CP2E 2-Series Integrated Control Processor DRAM DRAM is used by the operating system for dynamic storage of variables, signals and other constructs used at runtime. The actual amount of DRAM used at any given time depends on the particular program that is running, i.e., usage is variabl...
Page 14 - Ear Attachment for Rack Mounting (CP2E shown in illustration); closest to the front panel.; Bussing Strip Installation; To utilize the bussing strip, determine the number of relays to be
2-Series Integrated Control Processor Crestron CP2/CP2E Ear Attachment for Rack Mounting (CP2E shown in illustration) 1. Using a Phillips screwdriver, remove and retain the three side screws closest to the front panel. 2. Position a rack ear so that its mounting holes align with the vacated holes, a...
Page 15 - the bussing strip to provide strain relief.; Network Wiring; Exceeding the power output (maximum 24W) of the CP2/CP2E can
Crestron CP2/CP2E 2-Series Integrated Control Processor 5. Secure the wires connected to the terminal block with a tie wrap around the bussing strip to provide strain relief. Network Wiring NOTE: When making wire connections, refer to the latest revision of the Cresnet Network Interconnect Drawing (...
Page 16 - Wire Gauge Values; WIRE GAUGE; Hardware Hookup; Hookup Connections for the CP2/CP2E
2-Series Integrated Control Processor Crestron CP2/CP2E Wire Gauge Values RESISTANCE (R) WIRE GAUGE 4 16 6 18 10 20 15 22 13 Doubled CAT5 8.7 Tripled CAT5 NOTE: When daisy-chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors. Twist together the ends of the wi...
Page 17 - Optional Power Supply; Programming the CP2 and CP2E; )—registration is required for downloading.; CP2/CP2E Device Library Symbols; System Views; System Views of the CP2 and CP2E
Crestron CP2/CP2E 2-Series Integrated Control Processor Optional Power Supply The units can be powered through the NET network connector, or by an optional AC power pack (purchased separately). If an external power supply is to be used, Crestron recommends its CNPWS-75 External Power Supply or PW-24...
Page 18 - Add Item
2-Series Integrated Control Processor Crestron CP2/CP2E Slot 1: C2Net-Device The C2Net-Device slot enables the CP2 and CP2E to control up to 252 Cresnet devices. Each Cresnet device is assigned a unique identifier called a Net ID, which is a hexadecimal value ranging from 03 to FE. To view the list ...
Page 19 - In Program Manager, drag the C2I-IO8 symbol from; Signals; > configures that Versiport as an analog input. A Versiport can; Description; Internal configuration of a Versiport; > goes low, the output pin is driven to a
Crestron CP2/CP2E 2-Series Integrated Control Processor Slot 3: C2I-IO8 The CP2 and CP2E provide eight I/O ports called Versiports, each of which can function as a digital input, a digital output, or an analog input. Each Versiport has a corresponding pullup resistor. In Program Manager, drag the C2...
Page 20 - Digital Input Mode; MinChange
2-Series Integrated Control Processor Crestron CP2/CP2E Driving the corresponding <pu-disable> signal high can modify this behavior. This is not recommended, though, since it will cause the output pin to float when < o > goes low. Example 1 (recommended): The < pu-disable1 > signal...
Page 21 - MinChange1; Program View; About the IP Table; Functions | Setup IP Table
Crestron CP2/CP2E 2-Series Integrated Control Processor A voltage source is placed on Versiport 1 and < MinChange1 > is set to 10 via an Analog Initialize symbol. The value of < i1 > will not be propagated until it changes by at least 10. If the current value is 500, then a new value wil...
Page 23 - requiring
Crestron CP2/CP2E 2-Series Integrated Control Processor If the program contains SIMPL+ or User modules, the conversion might generate error messages. This is because modules and programs often contain symbols with “ambiguous” signals. For example, the inputs of the Serial to Analog symbol can be def...
Page 24 - Module Header Information; Yes; Establishing Communication with the CP2/CP2E; Serial Connection
2-Series Integrated Control Processor Crestron CP2/CP2E Module Header Information After you convert each module in a program, you can convert the program as described previously: drag the CP2 or CP2E onto the existing control system in System Views and click Yes to confirm the replacement. For furth...
Page 25 - To verify communication, click; Diagnostics | Establish Communications (Find; Open Viewport and click; Functions | Set Control System IP Information.; to set the new IP information.
Crestron CP2/CP2E 2-Series Integrated Control Processor • Hardware handshaking (RTS/CTS) enabled. • Software handshaking (XON/XOFF) not enabled. “Port Settings” dialog box: Default PC settings for RS-232 communication with the CP2/CP2E. To verify communication, click Diagnostics | Establish Communic...
Page 26 - Communication Settings; on the menu to display the “Port Settings” dialog box.; Troubleshooting Communications; has been selected. Some computers have more than one COM port
2-Series Integrated Control Processor Crestron CP2/CP2E use a CAT5 crossover cable to connect the two LAN ports directly, without using a hub. Once the cable connections are made, open the Crestron Viewport and click Setup | Communication Settings on the menu to display the “Port Settings” dialog bo...
Page 27 - Viewport Message
Crestron CP2/CP2E 2-Series Integrated Control Processor some may be internal (e.g., for a modem). Consult the manufacturer’s documentation for further information about the COM ports on your PC. 3. Check the ERR LED indicator on the front panel of the CP2/CP2E. If this LED is illuminated, unplug the...
Page 28 - “Send Program” Dialog Box
2-Series Integrated Control Processor Crestron CP2/CP2E Compiling and Uploading a Program to the Control System After you have completed your SIMPL Windows program you must compile and upload the program to the control system. To compile the program, simply click the Convert/Compile button on the SI...
Page 29 - Uploading Web pages to the CP2E
Crestron CP2/CP2E 2-Series Integrated Control Processor Another way to verify that the program has been transferred successfully is to select Report Program Information on the Viewport Functions menu. Program information is also displayed in the Viewport console whenever power is removed and re-appl...
Page 30 - Uploading Touchpanel Projects via the CP2/CP2E
2-Series Integrated Control Processor Crestron CP2/CP2E Uploading Touchpanel Projects via the CP2/CP2E You can use a connection to the CP2 or CP2E to upload VisionTools Pro-e projects to any Cresnet touchpanel. Compiled projects for TPS panels are contained in VTZ files; projects for all other touch...
Page 31 - confirm the transfer, click; Diagnostics | Check Ops Version; Viewport console should display the new .cuz version number.; Advanced Console Commands; control systems. You can access the CP2/CP2E console in; Special
Crestron CP2/CP2E 2-Series Integrated Control Processor 3. After the transfer is complete, the CP2/CP2E will automatically reboot. To confirm the transfer, click Diagnostics | Check Ops Version . The Viewport console should display the new .cuz version number. Advanced Console Commands The SIMPL Win...
Page 32 - Troubleshooting; CP2/CP2E Troubleshooting; TROUBLE; Network Analyzer; Windows
2-Series Integrated Control Processor Crestron CP2/CP2E Troubleshooting The table below and on the next page provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. CP2/CP2E Troubleshooting TROUBLE POSS...
Page 33 - Battery Replacement; Danger of explosion if battery is incorrectly replaced.; Passthrough Mode; Functions | Enter Passthrough Mode
Crestron CP2/CP2E 2-Series Integrated Control Processor Battery Replacement A Lithium battery is used to power the system clock within the CP2/CP2E. Under normal conditions, it will last for approximately 10 years. In the event that the clock fails, only an authorized technician should replace it. R...
Page 34 - Passthrough Mode Dialog Box; The PC will now be communicating directly with the device.; Functions | Exit Passthrough Mode; system reboot will also exit Passthrough mode.
2-Series Integrated Control Processor Crestron CP2/CP2E Passthrough Mode Dialog Box The PC will now be communicating directly with the device. To exit Passthrough mode, simply click Functions | Exit Passthrough Mode . A system reboot will also exit Passthrough mode. 30 • 2-Series Integrated Control ...
Page 35 - Further Inquiries
Crestron CP2/CP2E 2-Series Integrated Control Processor Further Inquiries If after reviewing this Operations Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: • In the US and Canada, call Crestron's co...
Page 36 - Software License Agreement; LICENSE TERMS; consent of Crestron.; OTHER LIMITATIONS
2-Series Integrated Control Processor Crestron CP2/CP2E Software License Agreement This License Agreement (“Agreement”) is a legal contract between you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for software referenced in this guide, which includes...
Page 37 - PROPRIETARY RIGHTS
Crestron CP2/CP2E 2-Series Integrated Control Processor If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity w...
Page 38 - Return and Warranty Policies; Merchandise Returns / Repair Service
2-Series Integrated Control Processor Crestron CP2/CP2E Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factor...
Page 39 - This page intentionally left blank.
Crestron CP2/CP2E 2-Series Integrated Control Processor This page intentionally left blank. Operations Guide - DOC. 5980 2-Series Integrated Control Processor: CP2/CP2E • 35
Page 40 - Operations Guide – DOC. 5980; Specifications subject to
Crestron Electronics, Inc. Operations Guide – DOC. 5980 15 Volvo Drive Rockleigh, NJ 07647 02.02 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
