Craftsman Assure Link Garage Door Opener Smartphone Control Kit (No service fees, free app download)- User Manual

1

ASSURELINK

TM

GARAGE DOOR OPENER

SMARTPHONE CONTROL KIT

MODEL 139.53999

To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing door control.
• Connect ONLY to 7-28 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing
garage door:
• Install door control within sight of garage door, out of reach of

children at a minimum height of 5 feet (1.5 m), and away from ALL
moving parts of door.

• NEVER permit children to operate or play with door control push

buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER

permit anyone to cross path of closing garage door.

• DO NOT install this door control on garage door opener systems

controlling one-piece or swing doors.

To provide an adequate visual alert, the garage door opener light
bulb(s) MUST be a minimum of 40 Watt (or equivalent).

This kit includes the Assurelink™ Control Panel model 41a7928-1 and the
Assurelink™ Internet Gateway model 41A7665. The control panel is
intended to be installed with Craftsman

®

Security

✚

™ Garage Door

Openers manufactured between 1998 and present. The Assurelink™
Control Panel is NOT compatible with Security

✚

2.0™ Garage Door

Openers. DO NOT install this door control on garage door opener
systems controlling one-piece or swing doors.

APPLICATION

The Assurelink™ Control Panel offers a quick and convenient way to add
Assurelink™ technology to your existing garage door opener. Assurelink™
technology uses a 900MHz signal to provide two-way communication
between the garage door opener and Assurelink™ enabled accessories.
When programmed to the Assurelink™ Internet Gateway you can monitor
and control your garage door from any internet enabled computer or
smartphone. You may program up to 12 Assurelink™ remote controls, 2
Assurelink™ keyless entries and a combination of 16 Assurelink™
accessories to the Assurelink™ control panel. For full compatibility, see
page 4.

OVERVIEW

Install the control panel in place of the existing door control. Due to
power consumption the control panel cannot be used in conjunction with
another wired door control connected to your garage door opener. If an
additional door control is needed, the

wireless door control model

41A7773-1

can be programmed to the control panel. To program the

41A7773-1 to the control panel, follow the remote control programming
steps. When in battery back-up mode, any feature using unattended
operation such as Timer-to-Close, closure from a garage door and gate
monitor or remote operation utilizing the Assurelink™ Internet Gateway
will be disabled.
1. Disconnect all electrical and battery power (if applicable) to the

garage door opener.

2. Remove the existing door control from the wall.
3. Note the polarity of the wires connected to the existing door

control.

• Label the wire connected to the RED terminal.

• Label the wire connected to the WHITE terminal.

Disconnect the wires from the existing door control.

4. Connect the wires to the new control panel. Make sure the polarity

is correct.

• Red wire to the R terminal.

• White wire to the W terminal.

5. Mount the control panel to the wall.
6. Reconnect power. The yellow command LED and the red learn LED

will blink quickly for up to 5 minutes as the control panel
recharges. When the control panel is operational, the yellow
command LED will glow steadily.

7. To test the control panel, press the push bar to activate the garage

door opener.

INSTALL THE ASSURELINK™ CONTROL PANEL

Existing Door Control

Discard, donate
or recycle

Wire from
RED terminal

Connect
RED wire to

R

terminal

Wire from
WHITE
terminal

Connect
WHITE
wire to

W

terminal

Assurelink™ Control Panel

•

If the yellow command LED does not turn on, reverse the wires
connected to the R and W terminals of the control panel. Replace
wire if necessary.

•

If yellow and red LEDs are blinking slowly, the control panel is not
compatible with your garage door opener.

•

If the yellow and red LEDs are blinking quickly, the control panel is
charging, and may take up to 5 minutes to become operational.

TROUBLESHOOTING