Page 2 - NOT
2 TABLE OF CONTENTS Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6Assembly . ....
Page 5 - THINK SAFETY; UNPACKING
5 • Never feed material into the cutting tool from the rear of the saw. An accident and serious injury could result. THINK SAFETY Safety is a combination of operator common sense and alert-ness at all times when the saw is being used.Never use another person as a substitute for a table exten-sion, o...
Page 6 - ASSEMBLY; SAW INSTALLATION
6 IMPORTANT: Table is coated with a protectant. To ensure proper fit and operation, remove coating. Coating is easilyremoved with mild solvents, such as mineral spirits, and a softcloth. Avoid getting solution on paint or any of the rubber orplastic parts. Solvents may deteriorate these finishes. Us...
Page 10 - RAIL ASSEMBLY
• If an adjustment is necessary, proceed as follows: Loosen and remove the six socket pan head screws and the rearpanel (see Figure 22). Loosen the four hex head bolts onthe trunnion (see Figure 23) and shift trunnions until aposition is found where the saw blade is parallel to themiter guage slots....
Page 12 - RIVING KNIFE TO BLADE ADJUSTMENT; INSTALL TABLE INSERT
• Make sure locking pin is aligned with riving knife hole and secure in position by tightening locking knob. • Riving knife must be in line with blade. Make sure riving knife sits flat against mounting bracket and lock plate. RIVING KNIFE TO BLADE ADJUSTMENT • Riving knife to blade clearance: the ga...
Page 13 - INSTALLATION
13 INSTALL MITER GAUGE Refer to Figure 37.• The miter gauge comes preassembled. Unpack the miter gauge and clean thoroughly. Insert into storage slots onright side of cabinet. INSTALL PUSH STICK Refer to Figure 38.• Insert the push stick into brackets on left side of base. INSTALL RIP FENCE Refer to...
Page 14 - EXTENSION CORDS; OPERATION; DESCRIPTION; Capacity with 10
• Inspect tool cords periodically and if damaged, have them repaired by an authorized service facility. • Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cordor plug is necessary, do not connect the green (or greenand yellow) wire to a li...
Page 15 - Rip Fence Dimensions:; STARTING AND STOPPING THE SAW
Rip Fence Dimensions: Rip fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 1 ⁄ 4 ″ Rip fence rails (front and rear) . . . . . . . . . . . . . . . . . . . . . 56 1 ⁄ 2 ″ Blade capacity maximum . . . . . . . . . . . . . . . . . . . . . . . . . . 10 ″ Blade arbor . . ....
Page 17 - PERPENDICULAR ADJUSTMENT; CURSOR ADJUSTMENT
RIP FENCE ADJUSTMENT The saw's rip fence is precision manufactured, incorporatingfine adjustments for accurate cuts. The saw is built to allowthe operator to accurately adjust the rip fence without prob-lems in a matter of seconds. LEVELING THE FENCE TO THE TABLE • Lift the lock handle to unlock the...
Page 19 - MAINTENANCE; CLEANING
COMPOUND MITER CUTTING This cut is performed with the miter gauge, and is a combina-tion of miter cutting and bevel crosscutting. The cut is made atangle other than 90° to both the edge and flat side of wood. RIPPING WARNING: When bevel ripping and whenever possible, place the fence on the side of t...
Page 20 - Repair Protection Agreements; Here’s what the Repair Protection Agreement*; Sears Installation Service
• Use soap and soft water on rubber and plastic parts.• After cleaning, lubricate unpainted surfaces with a light application of medium consistency machine oil. This lubri- cation should be repeated at least once every six months. NOTE: Instead of oil, a good quality paste wax can be applied to rip ...
Page 21 - Service Record; Contractor Table Saw; DATE
21 Service Record Craftsman 10 ″ Contractor Table Saw DATE MAINTENANCE PERFORMED REPLACEMENT PARTS REQUIRED
Page 22 - TROUBLESHOOTING; SYMPTOM
22 TROUBLESHOOTING SYMPTOM Saw stops or will not start Excessive vibration Cannot make square cut when crosscutting Blade stalls (however, motor turns) Blade does not come up to speed Cut binds, burns or stalls when ripping Cut not true at 45 or 90° positions Tilt and elevating handwheeldifficult to...
Page 23 - CORRECTIVE ACTION
23 TROUBLESHOOTING (CONTINUED) SYMPTOM Saw makes unsatisfactory cut POSSIBLE CAUSE(S) 1. Dull blade2. Blade mounted backwards3. Gum or pitch on blade4. Incorrect blade for cut5. Gum or pitch on table CORRECTIVE ACTION 1. Sharpen or replace blade2. Turn blade around3. Remove blade and clean4. Change ...
Page 24 - Figure 55 - Replacement Parts Illustration for Rip Fence
24 Model 351.218330 Figure 55 - Replacement Parts Illustration for Rip Fence 26 13 24 11 11 12 2 1 3 3 4 5 6 14 27 28 29 25 30 31 15 7 8 8 10 10 19 18 17 16 20 21 22 23 9 9
Page 25 - REPLACEMENT PARTS LIST FOR RIP FENCE
25 * Standard hardware item available locally. REPLACEMENT PARTS LIST FOR RIP FENCE KEYNO. PART NO. DESCRIPTION QTY. 1 09845.00 3CMI-6 E-Ring 2 2 31107.00 Locking Handle 1 3 31108.00 8 x 50mm Spring Pin 2 4 31109.00 Bushing 1 5 31110.00 Shaft 1 6 31111.00 Cam 1 7 01923.00 5 x 30mm Spring Pin 1 8 311...
Page 26 - Figure 56 - Replacement Parts Illustration for Cabinet
26 Model 351.218330 Figure 56 - Replacement Parts Illustration for Cabinet 10 11 12 14 8 2 2 5 6 7 8 2 3 3 17 6 16 15 25 23 18 19 20 4 9 1 2 2 7 5 21 22 24 13
Page 27 - REPLACEMENT PARTS LIST FOR CABINET; RECOMMENDED ACCESSORY
27 REPLACEMENT PARTS LIST FOR CABINET * Standard hardware item available locally. KEYNO. PART NO. DESCRIPTION QTY. 1 31125.00 Scale 1 2 06346.00 6-1.0 x 12mm Socket Pan Head Screw 30 3 31126.00 Front Corner Support 2 4 31127.00 Front Panel 1 5 STD870820 8-1.25 x 20mm Socket Head Bolt* 4 6 STD852008 ...
Page 28 - Figure 57 - Replacement Parts Illustration for Rails
28 Model 351.218330 Figure 57 - Replacement Parts Illustration for Rails 31 32 33 28 30 29 27 26 24 24 24 25 25 25 41 7 39 38 36 37 35 21 23 14 13 21 20 15 22 23 23 2 6 8 9 1 10 11 12 19 18 16 17 45 3 4 5 43 40 44 34 42
Page 29 - REPLACEMENT PARTS LIST FOR RAILS
29 REPLACEMENT PARTS LIST FOR RAILS * Standard hardware item available locally. ∆ Not shown. KEYNO. PART NO. DESCRIPTION QTY. 1 31138.00 Paddle 1 2 31558.00 Switch 1 3 17933.00 Circuit Breaker,15A 1 4 STD863508 5-0.8 x 8mm Pan Head Screw* 2 5 STD852005 5mm Lock Washer* 2 6 STD851005 5mm Flat Washer*...
Page 30 - Model
30 Model 351.218330 Figure 58 - Replacement P ar ts Illustration fo r Base 19 20 21 24 23 22 25 13 18 6 6 6 17 16 13 13 15 1 1 2 1 13 4 9 4 4 4 3 2 2 3 5 5 5 5 5 5 5 2 1 7 7 7 7 8 9 6 8 3 28 28 34 27 26 26 32 31 30 29 29 33 10 11 14 12
Page 32 - Figure 59 - Replacement Parts Illustration for Blade Drive
32 6 59 15 16 17 58 34 36 37 38 7 8 9 10 11 12 13 20 21 22 36 28 25 26 24 24 26 25 32 33 47 40 74 70 71 72 73 41 65 75 76 77 78 79 79 81 82 83 84 85 87 88 16 17 56 53 46 45 44 30 43 31 29 27 30 86 80 50 51 49 16 52 17 54 55 17 42 66 67 68 69 38 39 60 62 61 37 35 23 2 1 3 19 18 17 16 14 15 48 4 5 Mod...
Page 33 - REPLACEMENT PARTS LIST FOR BLADE DRIVE
33 * Standard hardware item available locally REPLACEMENT PARTS LIST FOR BLADE DRIVE KEYNO. PART NO. DESCRIPTION QTY. 1 STD835016 8-1.25 x 16mm Hex Head Bolt* 1 2 STD852008 8mm Lock Washer* 1 3 16716.00 8mm Flat Washer (W) 1 4 STD843620 16-2.0mm Fiber Hex Nut* 1 5 STD851016 16mm Flat Washer* 1 6 311...
Page 34 - Figure 60 - Replacement Parts Illustration for Blade Guard
34 6 6 34 7 7 8 9 10 11 12 13 20 20 21 21 22 22 35 28 25 26 27 24 29 31 30 32 33 5 4 4 37 36 9 23 2 2 2 1 3 3 19 18 17 16 16 14 15 15 15 4 Model 351.218330 Figure 60 - Replacement Parts Illustration for Blade Guard
Page 35 - REPLACEMENT PARTS LIST FOR BLADE GUARD
35 REPLACEMENT PARTS LIST FOR BLADE GUARD * Standard hardware item available locally. ∆ Not shown. N/A Not available as replacement part. KEYNO. PART NO. DESCRIPTION QTY. 1 N/A 6-1.0 x 58mm Hex Head Bolt 1 2 STD840610 6-1.0mm Hex Nut* 3 3 STD851006 6mm Flat Washer* 2 4 N/A Spacer 3 5 31237.00 Left B...
Page 36 - Your Home; in your home; Our Home; Sears Parts & Repair Service Center; Para pedir servicio de reparación
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC ® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC MC Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC Get it fixed, at your home or ours! Your Home For exper...
