Cornelius SID650W/80-B - Manual

Page 2 - TABLE OF CONTENTS

i 91704 TABLE OF CONTENTS Page GENERAL INFORMATION 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESCRIPTION 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION INSTRUCT...

Page 4 - GENERAL INFORMATION; DESCRIPTION; Table 1. SPECIFICATIONS; Water Temperature

1 91704 GENERAL INFORMATION DESCRIPTION The Remcor S.I.D. (Spiral Ice Maker/Dispenser) is a unique, self-contained, counter top style unit that automati- cally makes hard, clear cube quality ice and stores it in a sealed hopper for sanitary dispensing. The ice is made by a new, patented process on a...

Page 5 - INSTALLATION INSTRUCTIONS; UNPACKING INSTRUCTIONS; evaporator and void the extended evaporator warranty.

2 91704 INSTALLATION INSTRUCTIONS UNPACKING INSTRUCTIONS 1. With the unit upright, carefully remove the shipping crate. Inspect for shipping damage and report any such damage to the shipper immediately. 2. Unlock and open the hinged service door on the upper left side panel. 3. Remove shipping tape ...

Page 6 - for more information on this product.; FIGURE 1. ELECTRICAL WIRING INSTALLATION INSTRUCTIONS

3 91704 IMPORTANT: To ensure proper ice maker operation and also to reduce the frequency of water-related service problems, a water filter should be installed. Remcor recommends the use of IMI Cornelius filter, model number 81COR01PS. For specific recommendations on these filter systems for your loc...

Page 8 - FIGURE 3. MOUNTING TEMPLATE MODEL SID650-80

5 91704 15- 7/8-IN. 14-IN. 5/8-IN. 2-- 9/16-IN. 26-IN. 29- 1/4-IN. 18 -3/4-IN. 22-IN. 1 -5/8-IN. UNIT OUTLINE FRONT 3/8 DIA. 4 PLACES 1- 29/32-IN. 1 -5/8-IN. NOTE: SHADED AREA INDICATES OPENING IN CABINET BOTTOM FOR BEVERAGE TUBING FOR --B, --BC MODELS ONLY FIGURE 3. MOUNTING TEMPLATE MODEL SID650-8...

Page 9 - BEVERAGE SYSTEM; Installation; hopper with power applied to unit.; Troubleshooting Guide.; Adjustment Procedures

6 91704 BEVERAGE SYSTEM “B”models contain beverage faucets only and must be supplied with cold product from any remote cold plate or refrigerated soda factory. “BC”units have a built-in cold plate, in addition to the beverage faucets and are de- signed to be supplied direct from syrup tanks and carb...

Page 12 - OPERATING INSTRUCTIONS; Table 3. HARVEST CYCLE

9 91704 OPERATING INSTRUCTIONS A temperature sensing control bulb located in the storage hopper starts and stops the ice-making process in response to ice level in the hopper. With this ice level control “calling”for ice (hopper ice level is low), ice begins to form on the stainless steel tubing coi...

Page 13 - FIGURE 6. WIRING SCHEMATIC

10 91704 L1 L2 BROWN BLUE TP COMPRESSOR CC 2 START RELAY START CAP RUN CAP 5 R 5 CONTROL TRANSFORMER 220 C STOP / RUN LPS HPS BIN T’STAT COMPRESSOR CONTRACTOR CC 1 2 HARVEST MOTOR RED BLUE CAP NC HT3 NO CONDENSER FAN AIR PUMP NC HG SOL VALVE RUN CLEAN HT2 NO WATER DUMP VALVE FLUSH NC HT4 NO C ICE TH...

Page 14 - FIGURE 7. WIRING DIAGRAM

11 91704 YEL BLUE LPS FUSE 1-1/4 AMP TIME DELAY AGITATOR MOTOR CAP CLEAN ICE MAKER RUN RUN STOP BLUE BLUE GRN BLK BLK G R N PUR YEL YEL RED RED RED RED RED P I N K R E D Y E L B L K HARVEST TIMER NEUTRAL TERMINAL BOARD SOME LOCATIONS MAY VARY G R N WHT W H T PUSH TO FLUSH BIN T-STAT HPS GATE SOLENOI...

Page 15 - FIGURE 8. REFRIGERATION SCHEMATIC

12 91704 HIGH PRESSURE CONTROL HIGH SIDE SERVICE PORT COMPRESSOR LOW SIDE SERVICE PORT TXV BULB LOW PRESSURE CONTROL TXV PRESSURE TAP EVAPORATOR EXPANSION VALVE (TXV) SUCTION ACCUMULATOR SIGHT GLASS HOT GAS SOLENOID VALVE AIR-COOLED MODELS CONDENSER CONDENSER FAN A B FILTER/ DRIER PRESSURE REGULATIN...

Page 16 - MAINTENANCE; REGULAR BASIS; Cleaning Instructions; EVERY THREE MONTHS; Maintenance/Adjustment; PERIODICALLY; both the ice maker and hopper.; Ice Maker Section; not contact exposed electrical wiring or components.

13 91704 MAINTENANCE REGULAR BASIS (or as required) Cleaning of the ice maker is recommended on a regular basis not only for sanitary reasons, but also to maintain the performance of the unit. Build-up of line and scale can hinder ice-making production rates and interfere with proper dispensing of t...

Page 17 - Dispenser Section; Note: It may be helpful to twist cover slightly.

14 91704 6. Move the water float valve reservoir to the “Clean”position by lifting slightly and pulling forward to raise the reservoir to the upper mounting screws. 7. Remove the float valve cover and add 4 ounces of Virginia Ice Machine Cleaner to the reservoir. CAUTION: Virginia Ice Machine Cleane...

Page 18 - FOR UNITS WITH BEVERAGE SYSTEM; Cold Plate

15 91704 7. Reverse steps above to reassemble ice chute. 8. Sanitize the inside of the hopper agitator, ice chute, the hopper cover and ice drop cover with a solution of 1 ounce of household bleach to 2 gallons of water. (200 PPM) 9. Replace the hopper cover and ice drop cover. Turn on the electrica...

Page 20 - TROUBLESHOOTING GUIDE

17 91704 TROUBLESHOOTING GUIDE The following pages contain troubleshooting charts designed to aid an experienced service person in diagnosing any operating problem which may be experienced. It is assumed that normal service techniques and skills are familiar to the person doing the troubleshooting. ...

Page 33 - MAINTENANCE/ADJUSTMENT PROCEDURES; THERMOSTAT ALTITUDE ADJUSTMENTS; COUNTERCLOCKWISE TURN; ICE THICKNESS ADJUSTMENT

30 91704 MAINTENANCE/ADJUSTMENT PROCEDURES THERMOSTAT ALTITUDE ADJUSTMENTS IMPORTANT: Adjust the bin thermostat setting only if storage hopper over fill is a problem. BIN THERMOSTAT 1. Open the hinged service door. 2. The adjustment screw is located below the “Flush”switch on the left side of the el...

Page 34 - hopper with power applied to the unit.

31 91704 CLEANING/REPLACE THE FILTER 1. Remove the filter from the cabinet panel by sliding it forward toward the front of the unit. 2. Wash the filter in a solution of warm water and a mild detergent. Do not use caustic detergents as they may attack the aluminum filter elements. 3. Dry filter thoro...

Page 35 - HARVEST TIME ADJUSTMENT; viewed from the front of the unit.; MANUAL FILLING; contact with these components.

32 91704 HARVEST TIME ADJUSTMENT WARNING: Disconnect electrical power to the unit before servicing the timer in the electrical box. 1. Disconnect power to ice maker. 2. Remove upper front panel and electrical control box cover. 3. Place the “Stop/Run”switch in the “Stop”position. 4. Using Figure 9 a...

Page 36 - FIGURE 9. HARVEST TIMER

33 91704 9A FIGURE 9. HARVEST TIMER Distributed By: Commercial Refrigeration Service, Inc. WWW.IceCubes.NET WWW.CorneliusParts.COM (866) 423-6253 623-869-8881

Page 37 - PARTS LIST

34 91704 PARTS LIST DESCRIPTION PART NUMBERS Air Cooled Water Cooled Dispenser Components 80 80 “BC” 80 80 “BC” Gate Slide 21491 21491 21491 21491 Depressor Retainer 22644 22644 22644 22644 Agitator 22855 22855 22855 22855 Vend Switch 30895 30895 30895 30895 Switch Boot 31007 31007 31007 31007 Agita...

Page 39 - WARRANTY; IMI Cornelius Offices

SD 99-3 1/16/96 91704 IMI CORNELIUS INC . O NE C ORNELIUS P LACE A NOKA, MN . 55303--6234 T ELEPHONE (800) 238--3600 F ACSIMILE (612) 422--3232 T ECH S VC 1-800-535-4240 WARRANTY IMI Cornelius Inc. and Remcor Products Company warrants that all equipment and parts are free from defects in material an...

Page 40 - Remcor Incorporated

CORPORATE HEADQUARTERS: Remcor Incorporated 500 Regency Drive Glendale Heights, IL 60139 (708) 980--6900 Distributed By: Commercial Refrigeration Service, Inc. WWW.IceCubes.NET WWW.CorneliusParts.COM (866) 423-6253 623-869-8881

Cornelius SID650W/80-B - Manual

Table of Contents:

Summary

Other Cornelius Models