Conair Water/Spray Tanks - Manual

Conair Water/Spray Tanks

Conair Water/Spray Tanks – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
Page: / 38

Table of Contents:

  • Page 5 – ATTENTION: Read this so; NTRODUCTION
  • Page 7 – EAD THIS SO NO; This equipment is powered by three-phase
  • Page 9 – ESCRIPTION
  • Page 10 – reduces the buoyancy of the extrusion in; HAT IS THE; WT; OR; ST; ANK
  • Page 11 – In a WT water tank; , the extrusion is submerged in a flooded; In the ST spray tank; , the extrusion may be submerged or
  • Page 12 – PECIFICATIONS
  • Page 13 – The tank support system provides for
  • Page 14 – Vertical Adjustment System:; EATURES AND
  • Page 16 – Cooling Coils Option:; Cooling coils remove heat buildup; Thermometers Option:; On water tanks, thermometers
  • Page 17 – NSTALLATION
  • Page 18 – Installation Hardware Needed:; The WT/ST tank comes fully assembled in a single crate.; Carefully uncrate the tank; to make sure no; Take a moment to record serial numbers; and; You are now ready to begin installation.; Complete the preparation steps on the next page.
  • Page 19 – Make sure the installation area provides:; City, tower or chilled water may; A grounded 3-phase power source; supplying the
  • Page 20 – Position the tank downstream of the extruder.; If you have the horizontal adjustment option,; LIGNING THE; To avoid personal injury or damage; Improper installation could
  • Page 21 – ONNECTING; Open the electrical enclosure.; to the; Check every terminal screw; to make sure wires are
  • Page 22 – Connect the main water supply; Do not use deionized water, brine; For maximum water flow:; If you have a water
  • Page 23 – ESTING THE; Turn water supply on and fill the tank.; Water fills the tank to the water level you set.; If you have the optional recirculation system:; Press the REC START button.; Check the pump for proper rotation.; The pump; WARNING: Voltage Hazard; If a pump rotates in the wrong
  • Page 25 – PERATION
  • Page 26 – Determine the cooling mode you will use.; The extrusion should be fully; Make sure the extruder and puller are ready.; During; Side to Side adjustment:; Turn on the water supply to fill the tank.; Use; REPARING FOR
  • Page 27 – Thread the extrudate through the tank.; Turn the linear actuator handwheel to move; Recheck the tank alignment.; With the extrudate
  • Page 28 – TOPPING THE; You should check profile size and surface; section for product quality prob-
  • Page 29 – AINTENANCE
  • Page 30 – Drain and clean the tank.; Remove any particles and wipe all surfaces thoroughly.; Monthly; Drain and clean the reservoir.; Every 6 months; REVENTATIVE
  • Page 31 – grease gun; Drain the tank and reservoir.
  • Page 32 – Press the REC STOP button; A safety device; Inspect the wires and connections.; Look for; Inspect the exterior power cords.; Carefully; HECKING; WARNING: High voltage
  • Page 34 – Additional details about; A F; This machines should be
  • Page 35 – Increase spray bar flow.; Problem; Verify that the emergency
  • Page 37 – PPENDIX; To contact Customer Service personnel, call:; RE
  • Page 38 – Inspect the equipment and perform alterations or adjust-
Loading the manual

WARNING - Reliance on this Manual Could Result in Severe Bodily Injury or Death!

This manual is out-of-date and is provided only for its technical information, data and capacities. Portions of this manual
detailing procedures or precautions in the operation, inspection, maintenance and repair of the product forming the subject
matter of this manual may be inadequate, inaccurate, and/or incomplete and cannot be used, followed, or relied upon.
Contact Conair at [email protected] or 1-800-654-6661 for more current information, warnings, and materials about
more recent product manuals containing warnings, information, precautions, and procedures that may be more adequate
than those contained in this out-of-date manual.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 5 - ATTENTION: Read this so; NTRODUCTION

● ● Purpose of the User Guide . . . .1-2 ● ● How the guide is organized . . . .1-2 ● ● Your responsibilities as a user .1-2 ● ● ATTENTION: Read this so no one gets hurt . . . . . . . . . . .1-3 1-1 UGE014/0999 Water/Spray Tanks I NTRODUCTION

Page 7 - EAD THIS SO NO; This equipment is powered by three-phase

UGE014/0999 Water/Spray Tanks I NTRODUCTION 1-3 We design equipment with the user’s safety in mind. You canavoid the potential hazards identified on this machine by following the procedures outlined below and elsewhere in the User Guide. ATTENTION: R EAD THIS SO NO ONE GETS HURT ! WARNING: Voltage h...

Page 9 - ESCRIPTION

2-1 UGE014/0999 Water/Spray Tanks ● ● What is a WT or ST tank? . . . . .2-2 ● ● How it works . . . . . . . . . . . . . . .2-3 ● ● Specifications . . . . . . . . . . . . . .2-4 ● ● Features and options . . . . . . . . .2-5 D ESCRIPTION

Other Conair Models

All Conair Other