Code Alarm SRT 9000 - Manual

5 Charging the Battery Your 2-way transmitter is powered by a built-in 3.7V lithium polymer battery. When the screen displays low battery orthe icon is flashing it is time to recharge your remote transmitter. Charge the transmitter battery using the supplied plug-in home charger. While the battery o...

6 When the remote start “ ” icon is flashing press the “ ” icon button to display the remote start status. When the count down timer “ ” icon is flashing press the “ ” icon button to display the count down timer. Use buttons numbered 1-4 to start, stop or exit the countdown timer mode. When the star...

7 Vehicle Menu Options on the 2-Way Transmitter The 2-way transmitter allows multiple operations from the main four buttons by scrolling through the menu screens and selecting the desired function. To scroll through the menu screens press the “ ” switch up until the desired function is displayed. Pr...

9 Settings for the 2-Way Transmitter, continued Power Save Mode While in power save mode the 2-way transmitter will not attempt to communicate with the vehicle to conservebattery life. This feature is useful when leaving the vehicle for extended periods of time or if using the secondary 1way transmi...

10 Settings for the 2-Way Transmitter, continued Lighting for 2-Way Transmitter This setting adjusts the amount of time the 2-way transmitter’s display will remain active without activity. To adjustthe amount of time the display stays active scroll to menu 2 and select LIGHTING FOR OLED, then use th...

16 Using Valet Mode Using Valet Mode To engage valet mode: 1. Turn the ignition key to the ON position.2. Press and hold the emergency override button.3. The blue dashboard mounted LED will light solidindicating that the system is in valet mode. When valet mode is activated the dash mounted status L...

17 Using Your Remote Vehicle Starter, continued Preheating or Precooling the Vehicle’s interior Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system startsthe vehicle, the heater or air conditioning will activate and heat or cool the vehicle...

18 Using Your Remote Vehicle Starter, continued Operating the Daily Start Timer The system has the ability to start your vehicle based on a preset time entered into the 2-way transmitter. Prior toactivating this feature it will be necessary to enter the desired start time, refer to Daily Start Timer...

19 Page Call Out From within the vehicle, press and hold the emergency override button for 4 seconds, the2-way remote control will emit a beep and the vehicle call page will be displayed toindicate that someone is calling you to the vehicle. Additional System Features Check Vehicle Status To check t...

20 Anti Hi-Jack Active Anti Hi-Jack When Active Anti Hi-Jack is selected it must be activated by the transmitter each time it is needed. 1. While the ignition is ON, scroll to vehicle menu 1 and select CAR JACKING or press simultaneouslypress START and UNLOCK for 5 seconds. 2. If the vehicle’s door ...

21 Quick Reference Operation Guide, continued Remote control button operation. Transmitter Button System Function Notes / Button 1 Arm/Lock Press and release - Arm and Double Lock Pulse Press twice within 3 seconds - Arm/Lock and Bypass Zone 4 Press within 5 seconds - - Arm/Lock and Bypass Zone 6 Pr...

22 Replacing Remote Control Batteries 1-way 5 Button Remote Control: The two 3 volt lithium batteries inside the remote control should last approximately 1 year under normal use. When the battery becomes weak you will notice the remote control range (the distance from the vehicle the remotecontrol w...

23 Coded Override Procedure The system has an optional override mode that allows you to program a 2-digit personal code using the emergencyoverride button offering a higher level of security. This feature must be enabled by your installing dealer, thedefault override code is 11. 1. Enter the vehicle...

24 Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle security product (the “Product”), purchased from an authorized CODE dealer, that(except as provided below) should this Product under normal use and conditions, be proven...

26 FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of IndustryCanada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference thatm...