Code Alarm CA100 - Manual
Code Alarm CA100 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – II; ADJEST AND TEST THE SENSITIVITY LEVEL OF THE SHOCK SENSOR
- Page 3 – OPERATION MANUAL; TRANSMITTER OPERATION:; PASSIVE DOOR LOCKING:
- Page 4 – DISARMING WITHOUT A TRANSMITTER
05-04-06
CA100
1
MODEL CA100
REMOTE CONTROL AUTO ALARM SYSTEM
INSTALLATION & OPERATION INSTRUCTIONS
WIRING DIAGRAM
Main 5 Pin White harness
6 Pin White Mini Connector
Black Antenna Wire
LED Indicator
Valet Switch
Blue Wire: (-) 200mA Unlock Pulse
Green Wire: (-) 200mA Lock Pulse
2 Pin
White
2 Pin
Blue
2 Pin
White
5 Pin
White
6 Pin
White
MAIN 5 PIN WIRE HARNESS:
5. R ed W ire: +12V To C onstant Battery So urce
4 . Brow n W ire: Positive output T o Siren
3 . Black W ire: G round to Vehicle F R AM E
2. W hite W ire: Park in g Light R elay O utput
1 . R e d / W hite W ire: P ark ing Light R elay Pow er Input
15A Fuse
6 PIN MINI CONNECTOR WIRE HARNESS:
6. Tan Wire: (-) 200mA Programmable Output
2. Blue Wire: Instant Trigger Ground Input
1. Violet Wire: Positive Door Pin Switch Input
4. Pink Wire: To Ignition Switched + 12V
5. Orange Wire: 200mA Grounded when armed
3. Green Wire: Negative Door Pin Switch Input
85
86
30
87a
Cut
To start solenoid
From ignition switch
Red wire
White wire
Orange
wire
Channel 3 / 2 Step Door Unlock.
12V
12V
Yellow wire
A. PROGRAMMING TRANSMITTER:
Note:
This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch
3
times and holding in on
3rd
push until a long chirp is heard then release the valet
switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating the
signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each transmitter.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
05-04-06 CA100 2 Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. Three long chirps & Three parking light flashes confirm exit. B. ALARM FEATURES PROGRAMMING: ALARM FEATURE “ I ” PRORAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Val...
05-04-06 CA100 3 6. Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor. a). Activate the warn-away (first stage the shock sensor), the siren will emit a short chirp. b). Activate the full alarm (second stage the shock sensor), the siren will emit a long chir...
05-04-06 CA100 4 The vehicle doors will automatically lock after passive arming cycle has been completed. ACTIVE DISARMING – UNLOCK & DISARM: 1. Press button on the transmitter. 2. The siren will chirp twice and parking light will flash twice to indicating that the security system is now disarme...
