Clover TFT2288C - Manual

Contents 7 HDD INSTALLATION ............................................... ............................................................... ........ 147 9-1. HDD (H ARD D ISK D RIVE ) INSTALLATION ........................................................................ 148 APPENDIX ....................

9 About this manual This is the Instruction Manual for 22” Wide TFT-LCD monitor built-in 8Ch DVR system, Model LCD2284DVR, LCD2288DVR, TFT2284C and TFT2288C. The last digit of the model numbers (e.g.: 4 and 8) represent the number of cameras included in the system. This Manual describes how to insta...

11 Unpacking Care should be taken when unpacking to avoid damaging the system. Please check that the following items are included: Note : Contact your dealer immediately if any components are missing. 1 22” LCD Monitor built-in 8 Ch DVR 2-Indoor camera with C-mount lens 2-Outdoor camera with mountin...

System Instruction Manual 12 22” Wide LCD Panel Built-in 8 Ch Digital Video Recorder LCD2284DVR (LCD2288DVR, TFT2284C or TFT2288C) is the most reliable and functional embedded DVR system available today. The system displays 8 channels of live images in Real Time speed, compresses data digitally and ...

13 Features ▶ 22” Wide Screen - High resolution TFT-LCD 1,680 x 1,050, Contrast ratio 1,000:1, Response time 5 msec ▶ Multi Functional Record - Powerful, multiple Record Modes available: Manual (Continuous), Timer, and Motion Detection Recording. ▶ User friendly GUI - A few simple buttons for Easy c...

15 What to do at the time of Installation The system should be installed in the following order; 1. Make sure all the required hardware is available. - 22” wide TFT-LCD monitor built-in 8 Ch DVR - Up to 8 cameras ((Refer to the retail box for the number of camera in the system). - CCTV monitor or TV...

17 Specifications ITEM DESCRIPTIONS Television System NTSC PAL Refresh Rate 60 fields/sec 50 fields/sec Video Resolution 720x480 720x576 Video Inputs 8- 6pin Din Cameras or 8- BNC Cameras Video Input Signal Composite 1.0 Vp-p 75 Ohms Video Output 1- Composite output VIDEO SIGNAL Video Output Signal ...

19 Installation CONTENTS 5-1. CONTROLS AND CONNECTORS ................................................................................ 20 5-2. NOTE FOR INSTALLATION .......................................................................................... 23 5-3. SYSTEM CONNECTION .....................

System Instruction Manual 22 12. ALARM LED - The green LED will blink when an alarm is activated or video loss. 13. POWER LED - The red LED is lit when the Power switch on the rear of the system is ON. z Rear - A [Fig. 5-2 Rear View] USB CONNECTOR POWER INPUTPOWER SWITCH A USB PORT CAMERA IN EACH 12...

5. Installation 25 5-4. Installation 5-4.1. Camera Connection ▫ Connection of 6pin MINI DIN Cameras Connect the supplied cameras to the Camera Input (6pin mini DIN jack) on the back of the system as shown in [Fig. 5-2 Rear View]. ▫ Connection of BNC Cameras Connect the BNC cameras (not included) to ...

System Instruction Manual 26 - Place the system on the flat surface with soft fabric and set the proper angle of panel (screen) as shown [Fig.5-3-2]. - Attach the mounting bracket to the desired location on the wall. Locate wall studs and securely fix the mounting bracket with the supplied screws. 5...

5. Installation 27 5-4.4. RS485 Connection ▫ Connect the cable to the “RS485 PORT” on the terminal block of the system. Refer to [Fig 5-6] for connection of Connector PIN 5-4.5 Connection to an Ethernet Network (Optional) ▫ Connecting the cable to Ethernet. Our Ethernet connector is a RJ45 type. The...

29 How to operate CONTENTS 6-1. GENERAL INFORMATION ............................................................................................... 31 6-2. OPERATING INTERFACE................................................................................................ 32 6-3. IR REMOTE CONTROLLER...

6. How to Operate 35 ▫ Press the ENTER button to turn the power OFF. By clicking the mouse: ▫ Click the POWER OFF button on the MENU bar (See Fig.6-3 ) and then the message (See Fig.6-2 ) will be displayed on the screen. ▫ Click the OK button to turn the power OFF. 6-4.4 APPEARANCE OR DISAPPEARANCE ...

System Instruction Manual 38 6-6.2. SPLIT SCREENS 8 SPLIT SCREEN FULL SCREEN [4B] 2nd QUAD SCREEN [4A] 1st QUAD SCREEN SEQUENCING SCREEN

System Instruction Manual 40 6-7.3. SEQUENCING SCREENS ▫ Displaying the cameras in SEQUENCE is available in the LIVE mode or the RECORD mode. Each of the channels will be displayed in sequence and the dwell time can be adjusted in the camera set up menu (Refer to section 7-4.7). ▫ This ICON is displ...

6. How to Operate 41 6-7.4. LIVE AUDIO ▫ The basic system (LCD2284DVR) includes two indoor cameras built-in two way audio and two outdoor cameras built-in one way audio and IR LEDs (Infrared) to view objects in the darkness. Audio functions up to 4 cameras. ▫ To listen, click the CHANNEL button on t...

System Instruction Manual 42 of the system. ▫ To listen only (one way Audio), select one out of indoor/outdoor cameras by clicking the CHANNEL button on the MENU bar. Note : - It is impossible to communicate between the system and the cameras as long as the COMBO VIEWER (GUI) is being executed, even...

System Instruction Manual 44 6-7.6. OSD ON / OFF OSD ON /OFF is possible in the LIVE mode or RECORD mode. ▫ Click the OSD button on the MENU bar to turn the OSD (On Screen Display) ON or OFF. When the OSD is in OFF position, all the texts on the screen will be disappeared. [Fig.6-12 OSD OFF SCREEN] ...

System Instruction Manual 46 ▫ Channel Selection and Screen Conversion To change a channel, press the CHANNEL button on the remote controller or click the CHANNEL button on the [Fig.6-15 PAN /TILT CONTROL window]. It will be converted a full screen. To return to the LIVE mode, press the SPLIT button...

System Instruction Manual 48 6-7.9. POWER LOSS LISTS The list indicates the time/date when the system power was turned OFF. ▫ Click the POWER LOSS LISTS button on the SYSTEM STATUS window to view the POWER LOSS LISTS. ▫ Each of the pages contains 10 lists. You can search the pages by clicking the UP...

System Instruction Manual 52 6-8. Record This system provides Watchdog function. When power goes off during recording and then the power turns on, the system will automatically start recording. 6-8.1. Manual (Continuous) recording ▫ Click the SETUP icon on the MENU bar in the LIVE mode. ▫ Click the ...

System Instruction Manual 54 6-8.4. Timer Event Recording ▫ Click the SETUP icon on the MENU bar in the LIVE mode. ▫ Click the RECORD button in the SETUP menu and the RECORD window will be displayed. ▫ Select the TIMER RECORDING ( ) between the MANUAL RECORDING ( ) and the TIMER RECORDING ( ) as sho...

6. How to Operate 55 6-8.5. Recording Icons The Recording Icons depends on recording modes are displayed in the upper left hand corner of the screen. ▫ To turn the Recording Icon OFF, click the DISPLAY ON in the RECORD menu and then it will be turned OFF. You can select the value ON or OFF by repeat...

System Instruction Manual 56 6-9. REPLAY 6-9.1. QUICK REPLAY It is available only by pressing the QICK SEARCH button on the remote controller. ▫ Press the PLAY button, then the recent recorded data will be played. 6-9.2. REPLAY ▫ Click the REPLAY icon on the MENU bar, then the REPLAY window as shown...

System Instruction Manual 58 ▫ Select the hour on the Start Time Select Window (See Fig.6-32 ) by clicking the mouse on the Hour (0 – 23 hour) you wish to start to play. The green active buttons indicate the HOUR that contains recorded data, and the red active buttons indicate the selected Start HOU...

6. How to Operate 59 6-9.2.3. Replaying Replaying start time set-up can be possible within a recording time extent. ▫ Replay buttons (NORMAL / MOTION / SENSOR) NORMAL PLAY: Click the button to play all the recorded data. MOTION PLAY: Click the button to play the recorded data by MOTION only. SENSOR ...

6. How to Operate 63 6-10. COPY ▫ Click the COPY icon on the MENU bar, and then the COPY window as shown in [Fig.6-38] will be displayed. ▫ Click the (EXIT) button to return to the previous mode. 6-10.1. Copying devices In order to copy the recorded data, plug the USB devices such as external USB HD...

70 SETUP CONTENTS 7-1. SETUP .............................................................................................................................. 73 7-2. SYSTEM ........................................................................................................................... 74 7-...

7. Setup 71 CONTENTS 7-4. CAMERA .......................................................................................................................... 87 7-4.1. C AMERA ON/OFF ........................................................................................................ 88 7-4.2. C AM...

7. Setup 77 7-2.2. SYSTEM CONFIG ▫ Click the “SYSTEM CONFIG” button in the SYSTEM menu, and then the SYSTEM CONFIG menu will be displayed (See Fig.7-10 ). ▫ Click the “EXIT” button to return to the SYSTEM menu. 7-2.2.1. FACTORY DEFAULT ▫ Click the “ FACTORY DEFAULT ” button in the SYSTEM CONFIG menu...

System Instruction Manual 78 7-2.2.2. LOAD CONFIG / BACKUP CONFIG You can save up to four different settings in the BACKUP CONFIG and load the files in the LOAD CONFIG to change the settings to the system. ▫ LOAD CONFIG This function is to load the changed settings to the system. - Click the LOAD CO...

7. Setup 81 7-2.3. PASSWORD ▫ ON/OFF Select ON or OFF by clicking the mouse. If the ON is selected, the password has to be entered to get into the SETUP mode, RECORD mode, COPY mode, REPLAY mode, and when trying to connect the network through the COMBO VIEWER . ▫ PASSWORD CHANGE Click the password “...

System Instruction Manual 82 7-2.4. IR REMOTE ID Up to 16 DVR systems can be controlled by only one remote controller we provided, but IDs should be assigned on each of the systems. You don’t have to assign any ID on the single unit and you can control the system with the provided remote controller ...

System Instruction Manual 84 7-3. DISK MANAGER ▫ Click the “DISK MANAGER” button in the SETUP menu and then the DISK MANAGER window will be displayed (See Fig.7-22 ). ▫ A DVD R/W(USB) and 1 Hard Disk Drives can be installed, and all information in regards to the drives will be automatically displaye...

System Instruction Manual 90 7-4.5. Pan/Tilt Settings ▫ Click the PAN/TILT button on the corresponding channels in the CAMERA menu, then the PAN/TILT window will be displayed as shown in [Fig.7-33] . ▫ Click the (EXIT) button to return to the CAMERA menu. ▫ PTZ ID - Click the PTZ ID button in the PA...

System Instruction Manual 92 ▫ Baud rate Click the “BAUD RATE” button in the PAN/TILT window and choose a value among 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps on the Baud Rate pop-up window by clicking the mouse. ▫ Data Bits Click the “DATA BITS” button in the P...

System Instruction Manual 98 7-6.2. All Manual / Timer recording button ▫ Click the All Manual / Timer recording button in the RECORD menu, then the All Manual / Timer recording button will be displayed as shown in [Fig.7-55] . ▫ Select the Manual Recording button or Timer Recording button for all t...

System Instruction Manual 100 7-6.4. All Sensors ON / OFF ▫ Click the button in the RECORD menu, then the ALL SENSOR setup pop-up window will be displayed as shown in [Fig.7-60]. ▫ By clicking the mouse, select the on the pop-up window (See Fig.7- 60 ) to enable the system to start recording by Sens...

7. Setup 101 7-6.6. Recording Speed ▫ Click the F/S (Frames Per Seconds: Recording Speed) button on each of the channels in the RECORD menu, then the Recording Speed pop-up window will be displayed as shown in [Fig.7-64]. ▫ Select one of the Recording Speed among AUTO, 30, 15, 10, 7, 5, 3, 2, 1 and ...

System Instruction Manual 102 30 25 15 12 10 8 7 6 5 5 3 3 2 2 1 1 NTSC OFF PAL OFF 7-6.7. Recording Quality ▫ Click the QUALITY button on each of the channels in the RECORD menu, then the QUALITY pop-up window will be displayed as shown in [Fig.7-67] . ▫ Select one of the Recording Quality among LO...

7. Setup 103 7-6.8. Recording Mode The factory default setting for Recording is the Manual Recording (or called Continuous Recording), which keeps recording continuously if the OVERWRITE is set ON in the DISK MANAGE menu. This Manual Recording mode is one of the most popular Recording modes for user...

System Instruction Manual 104 7-6.9. Recording by Motion Detection When the menu of motion is properly set up (See section 7-6.3 for all the channels and this section for each of the channels) and detected motion of objects, the system begins recording automatically. The recording icon on the MENU b...

System Instruction Manual 106 ▫ Spot Setup If the “ON” is selected by clicking the mouse on the SPOT button in the MOTION menu, a full screen will display when a motion is detected. If the “OFF” is selected, the full screen won’t be displayed even though motion of objects is detected. ▫ Region The M...

System Instruction Manual 108 By Window Set Click the WINDOW SET button in the MOTION menu on each of the cameras and click one of cells (1,320 cells in total) for the starting point of the area which you would like to designate, and then click the other one of cells for the ending point of area unt...

System Instruction Manual 110 By Each Cell Click the EACH CELL button in the MOTION menu on each of the cameras and click the mouse on each of the cells as much as you would like to designate the Motion Detection Area. To clear, click the designated cells. Right-click on the current window to return...

7. Setup 111 ▫ Map View Click the MAP VIEW button in the MOTION menu to view the current settings for Motion detection area. Right-click on the current window to return to the MOTION menu. Note : Please pay attention to the following directions in order to use the Motion Detection function properly:...

System Instruction Manual 114 ▫ Alarm Hold Time Setup The system continues recording for the Alarm HOLD TIME and finishes the recording. Click the mouse on the HOLD in the SENSOR menu and choose one of the values among 1 through 30 seconds with the mouse’s wheel, and then click it to save. ▫ Spot Se...

System Instruction Manual 120 7-7.6. DDNS (DYNAMIC DOMAIN NAME SYSTEM) ▫ Select the DDNS button in the NETWORK menu by clicking the mouse or pressing the buttons on the remote controller. The DDNS menu will show up as shown in [Fig.7-103] . ▫ To return to the NETWORK menu, Click the (EXIT) button. ▫...

System Instruction Manual 122 7-7.7.2. Registration to the DDNS server Visit at www.dyndns.org to register. Registration to DYNDNS.ORG 1. Visit at www.dyndns.com . 2. Sign up for a new user name and a password: Click the Create Account on the upper right hand corner. 3. After signup new user, check ...

System Instruction Manual 124 7-8.1. VIDEO ENHANCEMENT ON EACH CAMERA ▫ Click on an INPUT button in the VIDEO ENHANCE menu. ▫ The CONTRAST and BRIGHTNESS sliders will be displayed along with camera picture as shown in [Fig.7-109] . ▫ Adjust Contrast and Brightness with the sliders by clicking the mo...

127 127 Remote Host Program CONTENTS 8-1. REMOTE PROGRAM OVERVIEW ................................................................................. 128 8-2. INSTALLING THE PROGRAM TO PC ............................................................................. 129 8-3. INTERNET EXPLORER ............

8. Remote Host Program 129 8-2. Installing the Program to PC Install the program into PC by using program CD (supplied) as follows. How to install the program 1. Start the operating system (Windows 2000/XP/VISTA). 2. Insert the program CD into CD-ROM drive. 3. Open My Computer , and then select CD-R...

System Instruction Manual 130 8-3. Internet Explorer When you are trying to use this function, it is highly recommended that the password should be turned ON in the SYSTEM menu not to enable unauthorized personnel to access your DVR system (See section 7-2.3). Up to 10 users can remotely access your...

System Instruction Manual 132 8-4. Remote Host [Fig.8-5 ComboViewer] Buttons of Remote Host Program ① Player button ② Connection button ③ Setup (Config) button ④ ⑤ Full Screen button Speaker / Microphone volume control ⑥ EXIT button ① ② ③ ⑤ ⑥ ④

8. Remote Host Program 133 8-4.1. Setup ① Version number It represents the current version number of the Firmware. ② Copy Refer to Section 8-4.5 in regards to copying methods after selecting one between the Quick Copy and the Live + Copy. ▫ Quick Copy Click on the Quick Copy for faster copying the r...

System Instruction Manual 136 8-4.3. Switch the Normal Screen to Full Screen ▫ Click the “FULL SCREEN” button on the COMBO VIEWER and then the current screen size will be enlarged to fit the monitor’s screen size, but the resolution will be lowered. ▫ Click the “FULL SCREEN” button again to go back ...

8. Remote Host Program 137 8-4.4. Speaker / Microphone Buttons of Remote Host Program ① PC Speaker ON/OFF: Turn the Speaker ON or OFF by clicking the mouse. ② PC Microphone ON/OFF: Turn the Microphone ON or OFF by clicking the mouse. ③ PC Speaker Volume Control: Adjust the Speaker Volume by clicking...

System Instruction Manual 138 8-4.5. Copy There are four icons such as NETWORK, USB, CD and DVD in the COPY menu of the COMBO VIEWER. The recorded data will be saved in the Backup Files (Open Windows Explorer – click My Computer - click the Program Files – click ComboViewer – click Backup Files) thr...

System Instruction Manual 140 8-5. PLAYER [Fig.8-14 Player] Chart. Button of Player Program ① Status window (Play mode, Date, Time) ② Calendar ③ Convert to AVI File ④ Search button for replaying ⑤ Capture button ⑥ Print button ⑦ Division button ⑧ Playback (Replay) speed Control ⑨ Search slider for r...

System Instruction Manual 142 - Click the Start Convert button on the Convert AVI window and click the CLOSE button after verifying the status “Complete” (See Fig.8-21 ). [Fig.8-17 Convert AVI window] [Fig.8-18 Backup Files by Networking] [Fig.8-19 DvrRecData by USB]

8. Remote Host Program 143 [Fig.8-20 Select one of the Channels] [Fig.8-20-1 Select folder for saving] [Fig.8-21 Start Convert Button] How to play the AVI files By using Windows media player: - Click the OPEN button on the Convert AVI window and double click one of the AVI files to play. The AVI fil...

System Instruction Manual 144 ④ Search button for Replaying - Click the Search button on the Player and the DVR Player will be displayed. - Select the folder that contains the recorded data and click the OK button on the DVR Player. One channel or all the channels can be replayed depends on the sele...

8. Remote Host Program 145 ⑦ Division button Select one of the following divisions while replaying. ⑧ Playback (Replay) Speed Control Move the slider with the mouse to control the replaying speed. The “0” represents the normal speed, “-“and “+” represents slow speed or fast speed respectively. [Fig....

147 HDD Installation CONTENTS 9-1. HDD (HARD DISK DRIVE) INSTALLATION .................................................................... 148 9

System Instruction Manual 148 9-1. HDD (Hard Disk Drive) INSTALLATION The system manufacturer already installed a large space of Hard Disk Drive (refer to the retail box for capacity) in the system. Just in case, refer to the following explanation on how to install a HDD. ▶ The power switch must be ...

9. Installation of additional HDDs 149 ▶ After pushing the HDD to the left and securely fix the bracket to the system with two screws. Connect the power connector and the data cable to the HDD. ▶ After pushing the HDD to the right and securely fix the bracket to the system with two screws.

System Instruction Manual 150 ▶ Assemble the HDD cover and securely fix it to the system with two screws. ▶ Plug the AC power cord to the system and an AC outlet. Turn on the power switch on the back of the system and the following window will be displayed. Check the power cable and the data cable c...

9. Installation of additional HDDs 151 ▶ Update the Firmware with USB memory (or CD-RW/DVD-RW). - Copy the Firmware to USB memory (or CD-RW/DVD-RW). -Plug the USB memory to USB Port of the system and select USB/CDRW/DVD on the following window. ▶ If the Firmware is detected, the Firmware lists will ...

153 APPENDIX CONTENTS FACTORY DEFAULT SETTINGS ...........................................................................................156

System Instruction Manual 154 Recording time table HDD: 500GB Recording Resolution: Half D1 (720 x 240) Based on 8 cameras HOURS Each (Total) 30 fps (240fps) 15 fps (120fps) 10 fps (80fps) 7 fps (56fps) 5 fps (40fps) 3 fps (24fps) 2 fps (16fps) BEST 58.00 115.00 173.00 249.00 347.00 579.00 870.00 HI...

155 Factory default settings (1) LIVE SCREEN 8 SPLIT OSD ON (2) TIME / DATE DISPLAY : ON TIME FORMAT : 24 HOUR DATE FORMAT : YYYY/MM/DD (3) LOAD / BACKUP CONFIG NONE LISTS (4) USER ACCOUNT PASSWORD : SET YOUR PASSWORD ( THE PASSWORD IS NULL ) PASSWORD ON/OFF : OFF (5) IR REMOTE ID OFF (6) HDD OVERWR...

System Instruction Manual 160 I cannot login ▶ Please check if the link LED of DVR and LAN port of PC are lit. ▶ Please check if the IP address on DVR and the PC is identical. Check SYSTEM STATUS by pressing STATUS button of DVR (Available on LIVE mode and RECORD mode.) MY IP : xxx.xxx.xxx.xxx Check...

161 Limited 1Year Warranty This warranty gives the original purchaser specific legal rights and you may also have other rights, which may vary from state to state. If our products do not function because of any defect in material or workmanship, we will repair it for free for 1 year on parts and lab...

System Instruction Manual 162 How to obtain Factory Service • Original purchaser must fill out the warranty card and mail it to the factory with the model number, serial number and the date of purchase. • We will repair or replace, and return the system to the owner under this limited warranty. • Pl...