Page 3 - Contents; CONTENTS; DVR
Contents CONTENTS ABOUT THIS MANUAL ............................................................... ...........................................................9 UNPACKING ............................................................... ............................................................... ....
Page 5 - DISK
Contents 7-2.1. TIME / DATE ............................................................................................................................... 76 7-2.2. SYSTEM CONFIG ...................................................................................................................... 7...
Page 6 - VIDEO
Stand-alone DVR Instruction Manual 7-6.8.2. Manual Event Recording .................................................................................................... 105 7-6.8.3. Timer Recording (Schedule Recording) ............................................................................. 105 ...
Page 9 - About this manual; This is the Instruction Manual for Stand-alone type DVR model
About this manual This is the Instruction Manual for Stand-alone type DVR model CDR0850 . This Manual describes how to install and operate the Stand-Alone DVR and provides specifications and features. Please read this manual thoroughly and follow the installation process before using Stand- alone DV...
Page 11 - Unpacking
1 Unpacking Care should be taken when unpacking to avoid damaging the unit. Please check that the following items are included: ▶ Stand-alone DVR unit ▶ All Accessories : Bracket, Power Cable, Screws ▶ Remote Controller & Battery ▶ PS2 Mouse ▶ DSUB 26p Connector (Sensor Input, Relay Output Selec...
Page 13 - Features
Features ▶ Multi Functional Record -Powerful, multiple Record Modes available: Manual (Continuous), Timer, and Motion Detection Recording. ▶ User friendly GUI -A few simple buttons for Easy control. ▶ Automatic System Recovery -Automatic and Complete System recovery within 10 seconds. ▶ Easy PTZ con...
Page 15 - Stand-alone DVR should be installed in the following order; Make sure all the required hardware is available.
3 What to do at the time of Installation Stand-alone DVR should be installed in the following order; 1. Make sure all the required hardware is available. - Stand-alone DVR unit (including HDD) - Up to 8 cameras (including power source) - CCTV or VGA monitor (or TV set) - Network cable if connecting ...
Page 17 - Specifications; ITEM
4 Specifications ITEM Television System NTSC PAL Refresh Rate 60 fields/sec 50 fields/sec Video Resolution 720x480 720x576 Video InputsVideo Input SignalVideo OutputsVideo Output SignalLive 240 Frames/sec display 200 Frames/sec display ZoomSequenceDisplay FormatVideo enhanceVGA enhance AUDIO FEATURE...
Page 19 - Installation
5 Installation CONTENTS 5-1. C ONTROLS AND C ONNECTORS (F OR 8C H & 16C H DVR) .........................................................20 5-2. N OTE FOR I NSTALLATION ........................................................................................................22 5-3. S YSTEM C ONNECT...
Page 22 - Use a compatible input/output signal type of cameras and monitor.
Stand-alone DVR Instruction Manual 5-2. Note for Installation Install the system according to the instructions described in this manual. This product is designed for indoor use and should not be used outdoors. Avoid any area with high humidity or dust which can shorten lifetime of the unit. ...
Page 24 - Connection of Normal Cameras; auxiliary monitor port is the same as the main monitor.; Connection of S-VHS Monitor
Stand-alone DVR Instruction Manual 5-4. Installation 5-4.1. Camera Connection ▫ Connection of Normal Cameras Connect the cameras to the Video Input (BNC connector) on the back of the unit as shown above [Fig. 5-3 System Connection]. ▫ Connection of Loop Output The Camera or video output is available...
Page 26 - capacity can cause system failure.; Refer to; the connection to; RELAY OUT
Stand-alone DVR Instruction Manual - 5-4.3. Sensor Connection and RELAY IN &OUT ▫ SENSOR Connection (SENSOR IN) Connect the sensor to ALM (SENSOR) IN. The Sensor should be a contactor type and support NO (Normal Open). Refer to [Fig. 5-6 SENSOR IN/OUT PIN] for connection. [Fig 5-6. SENSOR IN/OUT...
Page 28 - Connecting the cable to Ethernet.; to use a longer cable, we suggest using repeater.
Stand-alone DVR Instruction Manual 5-4.5 Connection to an Ethernet (Optional) Network ▫ Connecting the cable to Ethernet. Our Ethernet connector is a RJ45 type. The maximum cable length is 300 ft. When you want to use a longer cable, we suggest using repeater. Refer to [Fig. 5-11] for connector pin ...
Page 29 - switch conforms to the correct input voltage.
5. Installation 5-4.6. POWER CONNECTION Select proper voltage (see fig 5-12) and connect to a reliable power source. It should not be shared with other electrical equipment on the same line. Poor performance can occur if the connected voltage is more than 10% plus or minus the required voltage. Freq...
Page 31 - How to operate; IR
6 How to operate CONTENTS 6-1. G ENERAL I NFORMATION .........................................................................................................33 6-2. O PERATING I NTERFACE ..........................................................................................................34 6-3...
Page 33 - RS422C or the Ethernet port located on the back of the unit.
6. How to Operate 6-1. General Information ▫ You can operate all functions of the system by use of the 28 buttons located on the front panel, remote controller and a mouse. Additionally, you can remotely control this unit via RS422C or the Ethernet port located on the back of the unit. ▫ System stat...
Page 37 - stay on the MENU bar when the system is not connected through the; client’s computer when the system is connected through the; SmViewer; and the mouse; SmViewer; functions on the DVR system through internet.; pointer on the screen of the DVR system only, not on the SmViewer.
6. How to Operate 6-4.3. APPEARANCE OR DISAPPEARANCE OF POWER BUTTON The Power On/Off button and the Audio buttons (See 6-7.4) as shown in Fig.6-3-1 will always stay on the MENU bar when the system is not connected through the SmViewer (Client Host Program or Internet Explorer). But the Power On/Off...
Page 40 - FULL SCREEN
Stand-alone DVR Instruction Manual 6-6.2. SPLIT SCREENS FULL SCREEN SEQUENCING SCREEN [4B] 2nd QUAD SCREEN [4A] 1st QUAD SCREEN 8 SPLIT SCREEN 40
Page 42 - Displaying the cameras in SEQUENCE is available in the LIVE
Stand-alone DVR Instruction Manual 6-7.3. SEQUENCING SCREENS ▫ Displaying the cameras in SEQUENCE is available in the LIVE mode or the RECORD mode. Each of the channels will be displayed in sequence and the dwell time can be adjusted in the camera set up menu (Refer to 7-4.7). ▫ This ICON is display...
Page 44 - Click the ZOOM button on the MENU bar in the LIVE mode.
Stand-alone DVR Instruction Manual 6-7.5. ZOOM The image on the screen will be zoomed up to 2 times when the ZOOM button is clicked in the LIVE mode (This function is available on the full screen mode only). ▫ Click the ZOOM button on the MENU bar in the LIVE mode. ▫ Move the mouse on the ZOOMED scr...
Page 45 - OSD; button on the MENU bar to turn the OSD (On Screen Display) ON or OFF.
6. How to Operate 6-7.6. OSD ON / OFF OSD ON /OFF is possible in the LIVE mode or RECORD mode. ▫ Click the OSD button on the MENU bar to turn the OSD (On Screen Display) ON or OFF. When the OSD is in OFF position, all the texts on the screen will be disappeared. CAM 01 CAM 02 CAM 03 CAM 01 CAM 02 CA...
Page 46 - Click the
Stand-alone DVR Instruction Manual 6-7.7. PAN / TILT ▫ Click the PAN/TILT button on the MENU bar in the LIVE mode to access the PAN/TILT cameras. ▫ Click the (EXIT) button to return to the LIVE mode. [Fig.6-13 PAN/TILT button] [Fig.6-14 PAN/TILT window] 46
Page 47 - CHANNEL; Channel Selection and Screen Conversion; It will be converted a full screen.
6. How to Operate PAN / TILT CHANNEL ZOOM / FOCUS [Fig.6-15 PAN/TILT CONTROL window] ▫ Channel Selection and Screen Conversion To change a channel, press the CHANNEL button on the front panel or click the CHANNEL button on the [Fig.6-15 PAN /TILT CONTROL window]. It will be converted a full screen. ...
Page 50 - CLEAR LISTS button
Stand-alone DVR Instruction Manual ▫ CLEAR LISTS button Click the CLEAR LISTS button to clear the lists, you will be prompted to confirm changes. When you click the OK button, the POWER LOSS LISTS will be deleted. To cancel, click the CANCEL button Fig.6-19 POWER LOSS LISTS Message 50
Page 53 - OFF
6. How to Operate 6-8. Record This system provides Watchdog function. When power goes off during recording and the power turns on, the system will automatically start to record. 6-8.1. Manual (Continuous) recording ▫ Click the SETUP icon on the MENU bar in the LIVE mode. ▫ Click the RECORD button in...
Page 54 - ON
Stand-alone DVR Instruction Manual The MOTION ( ) and SENSOR ( ) as shown in Fig.6-24 should be turned ON in this recording mode. ▫ Press the RECORD button on the front panel or click the RECORD icon on the MENU bar. [Fig.6-24 Manual Event Recording setup] 6-8.3. Timer Recording ▫ Click the SETUP ic...
Page 56 - Recording Icons; corner of the screen.; or; by repeatedly clicking the mouse.
Stand-alone DVR Instruction Manual 6-8.5. Recording Icons The Recording Icons depends on recording modes are displayed on the upper left hand corner of the screen. ▫ To turn the Recording Icon OFF, click the DISPLAY ON in the RECORD menu and then it will be turned OFF. You can select the value ON or...
Page 58 - When the devices are ready to playback, the; on the corresponding devices will be; Ready; HDD
Stand-alone DVR Instruction Manual 6-9.2.1. Playback Devices In order to payback, plug the USB devices such as external USB HDD, USB memory to the USB port or insert a recorded media (CD-R/W or DVD-R/W) into the DVD-R/W drive. When the devices are ready to playback, the Ready on the corresponding de...
Page 59 - buttons indicate the selected Start HOUR.; By using the Replay Time set-up buttons:
6. How to Operate ▫ Select the hour on the Start Time Select Window (See Fig.6-32) by clicking the mouse on the Hour (0 – 23 hour) you wish to start to play. The green active buttons indicate the HOUR that recorded data exists, and the red active buttons indicate the selected Start HOUR. [Fig.6-32 S...
Page 60 - NORMAL PLAY: Click the button to play all the recorded data.
Stand-alone DVR Instruction Manual 6-9.2.3. Replaying Replaying start time set-up can be possible within a recording time extent. ▫ Replay buttons (NORMAL / MOTION / SENSOR) NORMAL PLAY: Click the button to play all the recorded data. MOTION PLAY: Click the button to play the recorded data by MOTION...
Page 64 - on the corresponding devices
Stand-alone DVR Instruction Manual 6-10. COPY ▫ Click the COPY icon on the MENU bar, and the COPY window as shown in Fig.6-38 will be displayed. ▫ Click the (EXIT) button to return to the previous mode. [Fig.6-38 COPY window] 6-10.1. Copying devices In order to copy the recorded data, plug the USB d...
Page 66 - channel selection
Stand-alone DVR Instruction Manual [Fig.6-40 Copy Start time and Channel Selection window] ③ channel selection ② HOUR selection button ① All channels HOUR selection ① All channels, HOUR selection button. Click the arrow button on the upper left corner as shown in Fig.6-40 to set the full extent of t...
Page 68 - To set the starting time and date to copy; Select each of channels (1 through 8 in red) or “; To set the ending time and date to copy,; right-click on the replaying screen again, and
Stand-alone DVR Instruction Manual 6-10.4. Copying the recorded data during replaying The system, CDR0850 allows users to copy the recorded data during replaying. ▫ Start replaying (See section 6-9). ▫ Right-click on the replaying screen, and the COPY DATA screen will be displayed (See Fig.6-43). ▫ ...
Page 70 - Save the recorded data on
Stand-alone DVR Instruction Manual DVD-RW COPY Save the recorded data on DVD-R/W Medias. Click the DVD-R/W button to start copy. ▫ As soon as one of the above button is clicked , copying will start along with displaying the icon shown in Fig.6-45. The following icon indicates that copying is in proc...
Page 71 - SETUP
7 SETUP CONTENTS 7-1. SETUP.................................................................................................................................74 7-2. SYSTEM ..............................................................................................................................75 ...
Page 76 - Click the “EXIT” button to return to the SYSTEM menu.
Stand-alone DVR Instruction Manual 7-2.1. TIME / DATE ▫ Click the “TIME/DATE” button in the SYSTEM menu, and the TIME/DATE menu will be displayed (See Fig.7-4). ▫ Click the “EXIT” button to return to the SYSTEM menu. [Fig.7-4 TIME / DATE menu] ▫ TIME FORMAT Click the mouse on the TIME FORMAT button ...
Page 78 - FACTORY DEFAULT; ” button in the SYSTEM CONFIG menu, and you will be
Stand-alone DVR Instruction Manual 7-2.2. SYSTEM CONFIG ▫ Click the “SYSTEM CONFIG” button in the SYSTEM menu, and the SYSTEM CONFIG menu will be displayed (See Fig.7-10). ▫ Click the “EXIT” button to return to the SYSTEM menu. [Fig.7-10 SYSTEM CONFIG] 7-2.2.1. FACTORY DEFAULT ▫ Click the “ FACTORY ...
Page 80 - BACKUP CONFIG
Stand-alone DVR Instruction Manual [Fig.7-14 LOAD CONFIG window] ▫ BACKUP CONFIG This function is to save the current settings to load the settings to the system. Save the current settings in the BACKUP CONFIG in order to load it to the system in the near future whenever you change the settings. - C...
Page 82 - Select ON or OFF by clicking the mouse.; PASSWORD CHANGE; The; Don’t forget the password.
Stand-alone DVR Instruction Manual 7-2.3. PASSWORD ▫ ON/OFF Select ON or OFF by clicking the mouse. If the ON is selected, the password has to be entered to get into the SETUP mode, RECORD mode, COPY mode, REPLAY mode, and when trying to connect the network through the SmViewer . ▫ PASSWORD CHANGE C...
Page 84 - USB memory
Stand-alone DVR Instruction Manual 7-2.5. FIRMWARE UPDATE There are two ways to update the firmware through USB memory and the SmViewer (GUI). We recommend users to update the firmware only in the LIVE mode. ▫ By USB memory - Format the USB with your computer and save the firmware file on it (not in...
Page 86 - stop recording when the space of HDD is in full.
Stand-alone DVR Instruction Manual 7-3.1. HDD WRITE FAIL If HDD is in full and the OVERWRITE on the HDD is turned OFF in the recording mode, the system will activate the relay output (See section 5-4.3) for a siren or other device. ▫ Click the HDD WRITE FAIL button in the DISK MANAGER window and sel...
Page 88 - the RECORD icon on the MENU BAR. It is possible only in the LIVE mode.
Stand-alone DVR Instruction Manual 7-4. CAMERA ▫ Click the “CAMERA” button in the SETUP menu and the CAMERA menu will be displayed (See Fig.7-26). To change the settings in the CAMERA menu, stop recording by clicking the RECORD icon on the MENU BAR. It is possible only in the LIVE mode. ▫ Click the ...
Page 90 - ” is
Stand-alone DVR Instruction Manual 7-4.3. Buzzer In order to alert users, the Buzzer will sound at that time video signal lost. ▫ Click on each of the channels you wish to turn the buzzer “ON” or “OFF”. If the “ O ” is selected, the buzzer will sound when video signal lost and if the “ X ” is select...
Page 92 - Pan/Tilt Vendor select
Stand-alone DVR Instruction Manual ▫ Pan/Tilt Vendor select Click the “PAN/TILT & REMOTE” button in the PAN/TILT window and the vendor lists will show up. Select a vendor on the vendor lists by clicking the mouse. Fig.7-34 PAN/TILT & REMOTE [Fig.7-35 PAN/TILT Vendor lists] ▫ Model Click the ...
Page 94 - Stop Bits
Stand-alone DVR Instruction Manual ▫ Stop Bits Click the “STOP BITS” button in the PAN/TILT window and select 1 or 2 on the Stop Bits pop-up window by clicking the mouse. [Fig.7-42 STOP BITS button] [Fig.7-43 Stop Bits pop-up window] ▫ Parity Bit Click the “PARITY BITS” button in the PAN/TILT window...
Page 98 - Adjust audio volume by clicking the
Stand-alone DVR Instruction Manual 7-5.3. Microphone Volume ▫ Adjust audio volume by clicking the ▲ or ▼ button. [Fig.7-53 Microphone Volume control button] 98
Page 100 - Timer; for more information related to
Stand-alone DVR Instruction Manual 7-6.2. All Manual / Timer recording button ▫ Click the All Manual / Timer recording button in the RECORD menu and the All Manual / Timer recording button will be displayed as shown in Fig.7-57. ▫ Select the Manual Recording button or Timer Recording button for all ...
Page 102 - HALF D1
Stand-alone DVR Instruction Manual 7-6.4. All Sensors ON / OFF ▫ Click the button in the RECORD menu and the ALL SENSOR setup pop-up window will be displayed as shown in Fig.7-62. ▫ By clicking the mouse, select the on the pop-up window (See Fig.7- 62) to enable the system to start recording by Sens...
Page 104 - up window by clicking the mouse.
Stand-alone DVR Instruction Manual 30 25 15 12 10 8 7 6 5 5 3 3 2 2 1 1 NTSC OFF PAL OFF [Fig.7-67 Recording Speed for each channel] 7-6.7. Recording Quality ▫ Click the QUALITY button on each of the channels in the RECORD menu and the QUALITY pop-up window will be displayed as shown in Fig.7-69. ▫ ...
Page 105 - Recording Mode
7. Setup 7-6.8. Recording Mode The factory default setting for Recording is the Manual Recording (or called Continuous Recording), which keeps recording continuously if the OVERWRITE is set ON in the DISK MANAGE menu. This Manual Recording mode is not only one of the most popular Recording modes for...
Page 106 - selected in this recording mode. If not, it won’t be recording.; Click the mouse on the
Stand-alone DVR Instruction Manual 7-6.9. Recording by Motion Detection When the menu of motion properly setup (See section 7-6.3 on page 101 for all the channels and this section for each of the channels) and detects motion of objects, the system begins to record automatically. The recording icon o...
Page 108 - Spot Setup; By All Set
Stand-alone DVR Instruction Manual ▫ Spot Setup If the “ON” is selected by clicking the mouse on the SPOT button in the MOTION menu, a full screen will display when a motion is detected. If the “OFF” is selected, the full screen won’t be displayed even though motion of objects is detected. [Fig.7-75...
Page 110 - By Window Set; Right-click on the current window to return to the MOTION menu.
Stand-alone DVR Instruction Manual By Window Set Click the WINDOW SET button in the MOTION menu on each of the cameras and click one of cells (330 cells in total) for the starting point of the area which you would like to designate, and then click the other one of cells for the ending point of area ...
Page 112 - By Each Cell
Stand-alone DVR Instruction Manual By Each Cell Click the EACH CELL button in the MOTION menu on each of the cameras and click the mouse on each of the cells as much as you would like to designate the Motion Detection Area. To clear, click the designated cells. Right-click on the current window to r...
Page 113 - Detection function properly:
7. Setup ▫ Map View Click the MAP VIEW button in the MOTION menu to view the current settings for Motion detection area. Right-click on the current window to return to the MOTION menu. [Fig.7-86 MAP VIEW button] Note : Please pay attention to the following directions in order to use the Motion Detec...
Page 116 - Alarm Hold Time Setup
Stand-alone DVR Instruction Manual ▫ Alarm Hold Time Setup The system continues recording for the Alarm HOLD TIME and finishes the recording. Click the mouse on the HOLD in the SENSOR menu and choose one of the values among 1 through 30 seconds with the mouse’s wheel, and then click it to save. [Fig...
Page 117 - pop-up window will be
7. Setup 7-7. NETWORK ▫ Click the “NETWORK” button in the SETUP menu and the NETWORK menu will be displayed on the screen as shown in Fig.7-94. ▫ Click the (EXIT) button to return to the SETUP menu. [Fig.7-94 NETWORK menu] 7-7.1. IP Mode ▫ There are two kinds of IP MODE, “DYNAMIC IP” and “STATIC-IP”...
Page 118 - OK
Stand-alone DVR Instruction Manual [Fig.7-95 IP Mode button] [Fig.7-96 IP Mode pop-up window] 7-7.2. GATEWAY, SUBNET, IP ADDRESS ▫ Click the GATEWAY / SUBNET / IP ADDRESS button in the STATIC IP MODE and the On Screen Keyboard will appear. ▫ Delete the current values with the button and enter the ad...
Page 124 - Registration to DYNDNS.ORG
Stand-alone DVR Instruction Manual 7-7.7.2. Registration to the DDNS server Visit at www.dyndns.org to register. Registration to DYNDNS.ORG 1. Visit at www.dyndns.com . 2. Sign up for a new user name and a password: Click the Create Account on the 3. eck your e-mail and confirm an e-mail from dyndns...
Page 126 - INPUT
Stand-alone DVR Instruction Manual 7-8.1. VIDEO ENHANCEMENT ON EACH CAMERA ▫ Click on an INPUT button in the VIDEO ENHANCE menu. ▫ The CONTRAST and BRIGHTNESS sliders will be displayed along with camera picture as shown in Fig.7-111. ▫ Adjust Contrast and Brightness with the sliders by clicking the ...
Page 127 - Click on the; VGA OUTPUT; in the; CONTRAST, BRIGHTNESS and SATURATION; sliders will be displayed along with; VIDEO ENHANCE
7. Setup 7 -8.2. VIDEO ENHANCEMENT ON VGA OUTPUT ▫ Click on the VGA OUTPUT in the VIDEO ENHANCE menu. ▫ The CONTRAST, BRIGHTNESS and SATURATION sliders will be displayed along with camera picture. ▫ Adjust Contrast, Brightness and saturation with the sliders by clicking the mouse. ▫ To return to the...
Page 129 - Remote Host Program
129 8 Remote Host Program CONTENTS 8-1. R EMOTE P ROGRAM O VERVIEW .............................................................................................130 8-2. I NSTALLING THE P ROGRAM TO PC ........................................................................................131 8-3. I N...
Page 131 - Remote Host Program; After the installation has been completed, the
8. Remote Host Program 8-2. Installing the Program to PC Install the program into PC by using program CD (supplied) as follows. How to install the program 1. Start the operating system (Windows 2000/XP). 2. Insert the program CD into CD-ROM drive. 3. Open My Computer , and then select CD-ROM drive. ...
Page 132 - be turned; Up to 10 users can remotely access your DVR with the HOST NAME.; How to setup the Internet Explorer; Registration to the; You should type the
Stand-alone DVR Instruction Manual 8-3. Internet Explorer When you are trying to use this function, it is highly recommended that the password should be turned ON in the SYSTEM menu not to enable unauthorized personnel to access your DVR system (See section 7-2.3). Up to 10 users can remotely access...
Page 134 - Buttons of Remote Host Program; Player button
Stand-alone DVR Instruction Manual 8-4. Remote Host ④ ⑥ ⑤ ③ ② ① [Fig.8-5 SmViewer] 134 Buttons of Remote Host Program ① Player button ② Connection button ③ Setup (Config) button ④ ⑤ Full Screen button Speaker / Microphone volume control ⑥ EXIT button
Page 135 - Version number
8. Remote Host Program 8-4.1. Setup ① ② ③ ④ [Fig.8-6 HOST CONFIG window] ① Version number It represents the current version number of the Firmware. ② Copy Refer to Section 8-4.5 in regards to copying methods after selecting one between the Quick Copy and the Live + Copy. ▫ Quick Copy Click on the Qu...
Page 137 - There are two ways to access the DVR through the; With Set Direct setting; NETWORK
8. Remote Host Program 8-4.2. Connection There are two ways to access the DVR through the SmViewer as follows. ▫ With Set Direct setting - Click the “CONNECT” button on the SmViewer and the SmViewer will be displayed. - Click the mouse on the “Set Direct” in the Connect Dialog menu and click the “ED...
Page 138 - “FULL SCREEN” button again to go back to the NORMAL SCREEN.
Stand-alone DVR Instruction Manual 8-4.3. Switch the Normal Screen to Full Screen ▫ Click the “FULL SCREEN” button on the SmViewer and the current screen size will be enlarged to fit the monitor’s screen size, but the resolution will be lowered. ▫ Click the “FULL SCREEN” button again to go back to t...
Page 139 - PC Speaker ON/OFF: Turn the Speaker ON or OFF by clicking the mouse.
8. Remote Host Program 8-4.4. Speaker / Microphone ⑤ ④ ① ② ③ [Fig.8-10 Speaker / Microphone ] Buttons of Remote Host Program ① Audio Input channel selection: Select the same audio channel as the DVR has. ② PC Speaker ON/OFF: Turn the Speaker ON or OFF by clicking the mouse. ③ PC Microphone ON/OFF: T...
Page 140 - client computer with these icons.
Stand-alone DVR Instruction Manual 8-4.5. Copy There are four icons such as NETWORK, USB, CD and DVD in the COPY menu of the SmViewer. The recorded data will be saved in the Backup Files (Open Windows Explorer – click My Computer - click the Program Files – click StandAlone MPEG4 DVR – click Backup ...
Page 142 - Chart. Button of Player Program
Stand-alone DVR Instruction Manual 8-5. PLAYER [Fig.8-14 Player] ⑦ ⑧ ⑩ ⑪ ⑫ ③ ④ ⑤ ⑥ ② ① ⑨ Chart. Button of Player Program ① Status window (Play mode, Date, Time) ② Calendar ③ Convert to AVI File ④ Search button for replaying ⑤ Capture button ⑥ Print button ⑦ Division button ⑧ Playback (Replay) speed ...
Page 143 - It indicates the play mode, date and time.
8. Remote Host Program ① Status window (Play mode, Date, Time) It indicates the play mode, date and time. [Fig.8-15 Status window] ② Calendar It shows the date currently being replayed. [Fig.8-16 Calendar] ③ Convert AVI File Convert the recorded files to AVI files. - Click the Convert AVI button on ...
Page 145 - By using Windows media player:
8. Remote Host Program [Fig.8-20 Select one of the Channels] [Fig.8-21 Start Convert Button] How to play the AVI files By using Windows media player: - Click the OPEN button on the Convert AVI window and double click one of the AVI files to play. The AVI files will save in the AVI Files folder (Open...
Page 146 - Search button for Replaying
Stand-alone DVR Instruction Manual ④ Search button for Replaying - Click the Search button on the Player and the Browse for Folder will be displayed. - Select the folder that contains the recorded data and click the OK button on the Browser for Folder. One channel or all the channels can be replayed...
Page 147 - Division button; Move the slider with the mouse to control the replaying speed.
8. Remote Host Program 147 [Fig.8-22 Print command window] [Fig.8-23 Print image] ⑦ Division button Select one of the following divisions while replaying. Full Screen 4 Division Screen 9 Division Screen 16 Division Screen [Fig.8-24 Division button] ⑧ Playback (Replay) Speed Control Move the slider w...
Page 149 - Installation of additional HDDs
9 Installation of additional HDDs CONTENTS 9-1. HDD (H ARD D ISK D RIVE ) INSTALLATION...........................................................................150 9-2. I NSTALLATION OF AN ADDITIONAL HDD ..................................................................................151 149
Page 150 - any of IDE Drives, the system won’t be working properly
Stand-alone DVR Instruction Manual 9-1. HDD (Hard Disk Drive) INSTALLATION ▶ Three of internal Hard Disk Drives (HDD) and a CD R/W or DVD R/W can be installed in the system. DVR manufacturer already installed a 320GB of Hard Disk Drive (IDE) and a DVD R/W. To install additional hard disk drives, ref...
Page 151 - Installation of additional HDDs; -2. Installation of an additional HDD; “Cable Select”; recognize the additional HDD.
9. Installation of additional HDDs 9-2. Installation of an additional HDD ▶ Set the jumper setting to “Cable Select” position on the additional HDD. Note : Be sure that the jumper setting is correct. If not, the system will not recognize the additional HDD. ▶ Turn off the power. Unscrew and remove t...
Page 153 - APPENDIX
APPENDIX CONTENTS R ECORDING TIME TABLE ............................................................................................................. 154 F ACTORY DEFAULT SETTINGS ...................................................................................................... 155 153
Page 154 - Recording time table
Stand-alone DVR Instruction Manual Recording time table HDD: 300GB Recording Resolution: Half D1 (720 x 240) Based on 8 cameras HOURS Each (Total) 15 fps (120fps) 10 fps (80fps) 7 fps (56fps) 5 fps (40fps) 3 fps (24fps) 2 fps (16fps) 1 fps (8fps) BEST 69.00 104.00 149.00 208.00 347.00 521.00 1041.00...
Page 155 - Factory default settings
Factory default settings (1) LIVE SCREEN 8 SPLIT OSD ON (2) TIME / DATE DISPLAY : ON TIME FORMAT : 24 HOUR DATE FORMAT : YYYY/MM/DD (3) LOAD / BACKUP CONFIG NONE LISTS (4) USER ACCOUNT PASSWORD : SET YOUR PASSWORD ( THE PASSWORD IS NULL ) PASSWORD ON/OFF : OFF (5) IR REMOTE ID OFF (6) HDD OVERWRITE ...
Page 159 - FAQ
FAQ CONTENTS I CANNOT LOGIN ......................................................................................................................... 160 159
Page 160 - I cannot login
Stand-alone DVR Instruction Manual I cannot login ▶ Please check if the link LED of DVR and LAN port of PC are lit. ▶ Please check if the IP address on DVR and the PC is identical. Check SYSTEM STATUS by pressing STATUS button of DVR (Available on LIVE mode and RECORD mode.) MY IP : xxx.xxx.xxx.xxx ...
Page 161 - Limited 2Year Warranty; consequential damages.
Limited 2Year Warranty This warranty gives the original purchaser specific legal rights and you may also have other rights, which may vary from state to state. If our products do not function because of any defect in material or workmanship, we will repair it for free for 2 year on parts and labor f...
Page 162 - How to obtain Factory Service; number, serial number and the date of purchase.
Stand-alone DVR Instruction Manual How to obtain Factory Service z Original purchaser must fill out the warranty card and mail it to the factory with the model number, serial number and the date of purchase. z We will repair or replace, and return the system to the owner under this limited warranty....