Page 2 - CAUTION
CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Explanation of two Symbols The lightning flash with arrowhead symbol, within an equilateral tri...
Page 3 - FCC CLASS B NOTICE
NOTE : This equipment has been certified and found to comply with the limits regulated by FCC, EMC and LVD. Therefore, it is designed to provide reasonable protection against interference and will not cause interference with other appliance usage. However, it is imperative that user follows this man...
Page 4 - CONTENTS
CONTENTS 1. GENERAL PRECAUTIONS 1 2. SPECIFICATIONS 3 3. OPERATION 5 3.1 FRONT PANEL 5 3.2 BACK PANEL 9 4. BASIC CONFIGURATION OF THE MONITOR SCREEN 10 4.1 START UP 10 4.2 LIVE SCREEN 11 4.3 RECORDING SCREEN 12 4.4 PLAYBACK SCREEN 13 4.5 RECORD AND PLAYBACK SCREEN 14 4.6 LIVE 15 4.7 RECORDING 16 4.8...
Page 6 - GENERAL PRECAUTIONS
1. GENERAL PRECAUTIONS 1. Read Instructions: All of the safety and operating instructions should be read and understood before the product is used. 2. Retain Instructions: The safety and operating instructions should be retained for future reference. 3. Heed Warnings: All warnings on the product and...
Page 8 - DVR SPECIFICATIONS
2. SPECIFICATIONS DVR SPECIFICATIONS System NTSC or PAL (Auto Detection) Video Input 4 Inputs (BNC): 1Vp-p composite, 75ohms Video Output 2 Outputs (BNC), 4 Looping output (BNC): 1Vp-p composite, 75 ohms Audio Input 1 Channel (RCA) Audio Output 1 Channel (RCA) Alarm Input 4 Ch alarm Inputs: Normally...
Page 9 - While recording, you can Playback and see the Live screen
Backup JPEG & AVI File format through GUI, DVR File format at USB. Ethernet RJ-45 Connector for network communication PAN / TILT RS-485 Control (Pelco D Protocol) USB Port Data Backup, Firmware Update Jog-Shuttle YES Setup On screen Display setup User Interface Menu driven User Input Device Fron...
Page 13 - WATERMARK CHECK; - To exit or return to the LIVE or RECORD mode, press this button on PTZ; is in full or data stop played.; NOTE; Recommended USB Memory
WATERMARK CHECK - Press and hold this button for about 3 seconds in the playback mode, the Water Mark OSD will be shown on the screen. To exit, press and hold this button again for about 3 seconds. - The WTMK function : Watermarking is an identification code or bit pattern integrated into the multim...
Page 15 - BASIC CONFIGURATION OF THE MONITOR SCREEN; Hard Drive information.
4. BASIC CONFIGURATION OF THE MONITOR SCREEN 4.1 START UP When the system starts up, the following pictures will be displayed in sequence. Firmware version # Hard Drive information. Operational information Function Title Network Configuration - 10 -
Page 19 - RECORD AND PLAYBACK SCREEN
4.5 RECORD AND PLAYBACK SCREEN REC, Playback OSD & Speed Time and Date Camera Title Indicates recording HDD Nine Screens in Record and Playback Mode Quad Screen in Record and Playback Mode REC, Playback OSD & Speed Time and Date Camera Title Camera Title Indicates recording HDD - 14 -
Page 20 - AUTO; button. It will available in the; LIVE; and; RECORD; button to return to the; QUAD; - Press the channel button to freeze the current display.
4.6 LIVE Live means viewing the present video images from the cameras on the monitor. 4.6.1 Full Screen display Full screen display is possible in the Live mode or Record mode. Use channel selection button to choose a corresponding video input. Refer to 4.2 “Full Screen in LIVE Mode” 4.6.2 Quad Scre...
Page 21 - Recording will start when the; button is pressed. The; indicator will be lit and ‘
- Press the same channel selection button to release the freeze function. Freeze symbol 4.6.7 OSD On / Off Available in the LIVE, RECORD or PLAYBACK mode. When the OSD button is pressed, all the texts except the REC and PB (PLAYBACK) OSD are cleared temporarily. When the button is pressed again whil...
Page 22 - Playback from the first recording time; When the; pause during playing, press; PLAY
The whole recording lists are updated hourly up to 1,000 lists on both Master and Slave. 4.7.3 Schedule recording Recording by scheduled time The time of record start and finish can be set to hour: minute. Refer to section 5.7.6 for more information. 4.7.4 ALARM recording When an alarm signal is rec...
Page 25 - SETUP SCREEN TREE
Page 40 - Registration to DYNDNS.ORG
5.11.2 HOST NAME • Choose the HOST NAME in the DDNS SET menu with the UP/DOWN buttons. • Press the ENTER button to change the values with the UP/DOWN buttons and select the digits (up to 8 digits) by using the LEFT/RIGHT buttons. • After changing the values, press the ENTER button. 5.11.3 USER NAME ...
Page 41 - Registration to CLOVERDVR.COM; Go; CAUTION The power switch must be turned off before installing
10. To complete, click Add Host on the bottom. 11. After registration, go to the DDNS SET menu on the DVR. 12. Refer to section 5.11 DDNS in this manual for the next step. Registration to CLOVERDVR.COM 1. Go to website www.cloverdvr.com 2. Select Insert New User. 3. Enter your ID and Password (up to...
Page 42 - INSTALL THE HDD2
4. Attach the HDD to the removable HDD rack and secure it with the supplied screws as below. 5. Assemble and put the removable HDD rack back in it’s place. 6. Turn the power on and see if the HDD is being recognized. 6.2 INSTALL THE HDD2 The HDD2 (SLAVE) can be installed inside of the system. The po...
Page 44 - ENTER; button is pressed.; ESC
7. PTZ CONTROL 1. Connect Pan/Tilt/Zoom camera’s control to RS485(+) / RS485(-) port on the rear of the system. 2. The video output of Pan/Tilt/Zoom camera to the one out of channel you wish to connect. 3. Press and hold the PTZ button for about 3 seconds on the front panel and the PAN/TILT CONTROL ...
Page 45 - System Configuration Diagram; TIME LAPS VCR
8. INSTALLATION 8.1 System Configuration Diagram The following illustration is showing the fully installed system. CH1 CH2 CH3 CH4 LOOP OUT VIDEO IN V - OUT1 A - IN A - OUT ETHERNET ALARM IN 1 2 3 4 GND + _ ALARM OUT AC INPUT AC100-240V,50/60Hz POWER ATTENTION CAUTION RISQUE DE CHOC ELECTROIQUE NE P...
Page 46 - on the back panel of the product.; is a looping output trough
8.2 CAMERA This product can be installed up to 4 cameras. Connect cameras to the VIDEO IN (BNC) on the back panel of the product. To connect a PTZ camera, connect the PTZ camera’s control line to the RS-485 (+, -) terminal and connect the video output to one out of VIDEO IN on the back panel of the ...
Page 47 - Speaker
CH1 CH2 CH3 CH4 LOOP OUT VIDEO IN V - OUT1 A - IN A - OUT ETHERNET ALARM IN 1 2 3 4 GND + _ ALARM OUT AC INPUT AC100-240V,50/60Hz POWER ATTENTION CAUTION RISQUE DE CHOC ELECTROIQUE NE PAS ENLEVER DO NOT OPEN RISK OF ELECTRONIC SHOCK RS485 V - OUT2 M ODEL NO : CDR4170 AC100-240V,50/60Hz, 25W CLOVER E...
Page 48 - MONITOR; DVR system; INSTALLING THE PROGRAM TO THE PC
TIME LAPS VCR CH1 CH2 CH3 CH4 LOOP OUT VIDEO IN V - OUT1 A - IN A - OUT ETHERNET ALARM IN 1 2 3 4 GND + _ ALARM OUT AC INPUT AC100-240V,50/60Hz POWER ATTENTION CAUTION RISQUE DE CHOC ELECTROIQUE NE PAS ENLEVER DO NOT OPEN RISK OF ELECTRONIC SHOCK RS485 V - OUT2 M ODEL NO : CDR4170 AC100-240V,50/60Hz...
Page 49 - CLDVR; icon on your desktop to connect the DVR through; GUI; and the
How to install the client program (CLDVR) 1. Start the operating system (Windows 98/2000/XP). 2. Insert the program CD into CD-ROM drive. 3. Open My Computer, and then select CD-ROM drive. 4. Select the CLDVR folder, and then double click SetupCLDVR.EXE. The software installation will begin. 5. Afte...
Page 51 - EXPLANATION OF CLDVR FUNCTION
1 2 3 4 2 clover.cloverdvr.com 1. CONNECTION STATUS INDICATOR It indicates that is currently being connected IP address and bandwidth (transmission speed). 2. FUNCTION OF BUTTONS Refer to next section. 3. LED DISPLAY, CLOCK The LED is lit depends on mode such as LIVE, PLAYBACK and RECORD. And the cl...
Page 52 - The following pop-up window will appear.
1. F/W (FIRMWARE) The FIRMWARE can be upgraded by pressing the F/W button or USB device. This button is not for users, only for manufacturers and distribution center. 2. SAVE • Click the SAVE button to save the video images that is currently being displayed on the GUI. • The following pop-up window ...
Page 54 - WAIT
Select Channel Reset button 7. PRINT • Click the PRINT button to print the current pictures shown on the GUI and then the following window pops up along with “ WAIT …” . Please wait a couple of seconds until the system loads data to print. 8. REC • Click the REC button to start or stop recording. Us...
Page 59 - button on the GUI and USB Memory.
9.5.2 PTZ CONTROL The following picture enables you to control PTZ camera connected to the system. ZOOM control PAN control FOCUS control TILT control PAN/TILT CONTROL Press UP key for TILT UP, DOWN key for TILT DOWN, LEFT key for PAN LEFT and RIGHT key for PAN RIGHT. FOCUS/ZOOM CONTROL Press “ Z+” ...
Page 61 - APPENDIX; SPEED
APPENDIX 1. RECORDING TIME TABLE (DAYS) 1.1 REC RESOLUTION (720H) / REC QUALITY (VERY HIGH) SPEED 40G HDD 80G HDD 120G HDD 200G HDD 01 IPS 15-Days 19-Hours 31-Days 12-Hours 47-Days 07-Hours 78-Days 19-Hours 02 IPS 7-Days 22-Hours 15-Days 19-Hours 23-Days 17-Hours 39-Days 12-Hours 03 IPS 5-Days 07-Ho...
Page 65 - PARTIAL MALFUNCTION OF SURVEILLANCE SCREEN; - Check the camera power, connection or cleaning of connection part.
[6-1] SCHEDULE REC : OFF [6-2] SCHEDULE REC SETTING : No setup data 6] DISPLAY [1] TITLE DISPLAY : ON [2] BORDER LINE : ON [3] TIME / DATE : ON [4] POSITION : BOTTOM 7] BUZZER [1] KEY BUZZER : ON [2] VIDEO LOSS : ON 8] ACCOUNT [1] DVR ACCOUNT SET [1-1] PASSWORD : OFF [1-2] PASSWOD CHANGE DEFAULT PAS...
Page 67 - serial number and the date of purchase.
Limited 2Year Warranty This warranty gives the original purchaser specific legal rights and you may also have other rights, which may vary from state to state. If our products do not function because of any defect in material or workmanship, we will repair it for free for 2 year on parts and labor f...
