Cisco 2020 - Manual

Cisco 2020

Cisco 2020 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
Page: / 32

Table of Contents:

  • Page 2 – Document any damage noted during the inspection.; Installing an LS2020 Switch in Rack; Cooling Air and Hardware Placement; The exhaust is not located near the air intake of other equipment.; Required Tools; A number 2 Phillips screwdriver for mounting the chassis.; Rack Installation Procedure
  • Page 6 – Wiring a DC-Powered System; Preparation for Wiring
  • Page 7 – Wiring Procedure; Replace the terminal block cover.
  • Page 8 – Installing Fantails; Required Tools and Equipment; Fantails in the desired quantity (provided by Cisco Systems).
  • Page 9 – Fantail Installation Procedure
  • Page 10 – Connecting Cables
  • Page 11 – Closing the Chassis; Applying System Power; To power up an LS2020 switch, perform the following steps:
  • Page 13 – Installing Modems
  • Page 14 – Basic LS2020 Configuration Tasks; Required Configuration Information; Host name for the LS2020 node.; Passwords
  • Page 15 – Host Name; Primary NP address and mask (for every LS2020 node in the network); each node must have a unique host ID.; each node in the network must have a unique host ID.
  • Page 16 – Subnet mask for the NP’s Ethernet address; Trunk Port Information; The number of the chassis slot in which the trunk card is located
  • Page 17 – Attaching a Terminal to a Console Port; Background Information
  • Page 18 – For the Console Port:
  • Page 19 – Method 1; Attaching a Terminal and Matching the Baud Rate
  • Page 20 – TCS SEL LED
  • Page 21 – Connecting the Terminal to the NP
  • Page 22 – Special Consideration: Running Scripts Separately
  • Page 23 – for this particular LS2020 node, effectively deleting the files.; Entering Configuration Data; Observe the system’s boot display:
  • Page 24 – Enter date
  • Page 25 – and the IP; If you answer
  • Page 26 – ” at the chassis
  • Page 30 – How to Proceed; Running Diagnostics; The node name and its IP address; Installing StreamView Network Management Software
  • Page 31 – Configuring the Network; If Your PC Has Two 1.44-MB Floppy Disk Drives; Enter the following command at the DOS prompt:
  • Page 32 – If Your PC Has One 1.44-MB Floppy Disk Drive
Loading the manual

C H A P T E R

Hardware Installation 2-1

2

Hardware Installation

This chapter provides procedures for installing a LightStream 2020 multiservice ATM switch
(LS2020 switch) in a networking environment. Installing an LS2020 switch involves several tasks in
two major categories:

1

Installing the LS2020 switch hardware

Separate sections in this chapter are devoted to the following topics:

— “Unpacking and Inspecting the LS2020 Switch Hardware”

— “Installing an LS2020 Switch in Rack”

— “Wiring a DC-Powered System”

— “Installing Fantails”

— “Attaching Data Cables”

— “Closing the Chassis”

— “Applying System Power”

2

Performing basic configuration procedures

The basic configuration tasks for the LS2020 switch are accomplished through configuration
scripts provided in this chapter.

Note

Refer to the LightStream 2020 Release Notes for important, release-specific information that

may not appear elsewhere in the LS2020 documentation set.

Unpacking and Inspecting the LS2020 Switch Hardware

When unpacking the LightStream 2020 switch, you should inspect the shipping container contents
to ensure the shipment is complete as well as check for damage that may have occurred during
shipment.

Step 1

Check the shipping container before removing the LS2020 switch hardware from the
loading dock and inspect it for any signs of in-transit damage.

Step 2

Transport the container to the systems area where the LS2020 switch is to be installed.

Step 3

Cut the packing straps and lift the cardboard box off the LS2020 chassis. Remove the
packing material and bill of materials.

Step 4

Check the bill of materials against the shipment received.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Document any damage noted during the inspection.; Installing an LS2020 Switch in Rack; Cooling Air and Hardware Placement; The exhaust is not located near the air intake of other equipment.; Required Tools; A number 2 Phillips screwdriver for mounting the chassis.; Rack Installation Procedure

2-2 LightStream 2020 Installation Guide Installing an LS2020 Switch in Rack Step 5 Inspect all external surfaces of the chassis for signs of damage. Pay special attention toareas of the chassis corresponding to visible damage to the shipping container. Step 6 Document any damage noted during the ins...

Page 6 - Wiring a DC-Powered System; Preparation for Wiring

2-6 LightStream 2020 Installation Guide Wiring a DC-Powered System Wiring a DC-Powered System The procedure in this section explains how to wire a DC-powered LS2020 switch to a DC powersource. This task should be performed only by qualified service personnel or a licensed electrician. This section a...

Page 7 - Wiring Procedure; Replace the terminal block cover.

Hardware Installation 2-7 Wiring a DC-Powered System Figure 2-3 Connections to DC-powered Chassis Wiring Procedure Warning The wiring task should be performed only by a licensed electrician or qualified service personnel. Untrained personnel may be exposed to hazardous DC voltages. To wire a DC-powe...

Other Cisco Models

All Cisco Other