Chamberlain CR550 - Manual - manualsarea.com

Page 2 - WARNING; must; START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS

1 CONTENTS PAGE SAFETY INSTRUCTIONS . . . . . . . .1CARTON INVENTORY . . . . . . . . . .2TOOLS REQUIRED . . . . . . . . . . . .2DOOR REQUIREMENTS . . . . . . . .2PREPARE & TEST THE DOOR . .3-4INSTALLATION . . . . . . . . . . . . . .5-6CONNECT ELECTRIC POWER . . .7ADJUSTMENT . . . . . . . . . . ....

Page 3 - on the door; DOOR REQUIREMENTS; Independent clamping method; fig A

2 1. Instruction manual (this document)2. Warning and risk of entrapment labels3. Hardware bag4. Release handle, cord and risk of entrapment card5. 3 Channel mini transmitter (2)6. Wall or visor mounted transmitter7. Stop collar8. Clamp bracket and plate9. Weight bar 10. Extension poles & brace ...

Page 4 - TESTING THE DOOR; Non opener side; INSTALLING THE STOP COLLAR; Is stop collar installed?; YES; Proceed to the next step

TESTING THE DOOR Complete the following test to ensure your door is wellbalanced, and not sticking or binding: • Disable all locks and remove any ropes connected to the garage door. • Lift the door to about halfway and then release it. The door should remain suspended entirely by its spring. • Raise...

Page 5 - PREPARING THE OPENER; PINNING THE DOOR; Attaching the extension poles (if required); Reinforcing brace must be used.

4 PREPARING THE OPENER 7 For left hand side installationsthe wire jumper should be removed. For right hand side installationsthe wire jumper should be in place(factory installed). Set opener position (left or right hand) Extension pole Reinforcing Brace Drive leg Note: A ballooning door may delay th...

Page 6 - INSTALLATION STEPS; FOR RIGHT HAND INSTALLATIONS; of the door is secure.

5 INSTALLATION STEPS 9 FOR RIGHT HAND INSTALLATIONS • Ensure that the opener position jumper (wire connector) is installed (refer Section 7). • Place the opener in manual release mode (refer Section 11).• Open the roller door fully. For safety, tie a rope around the door (as shown). • Mark the posit...

Page 7 - OPERATING THE MANUAL RELEASE; To disengage the opener; ATTACH THE RELEASE HANDLE AND CORD

10 • Thread one end of the rope through the hole in the top of the red handle so “NOTICE” reads right side up asshown. • Secure with an overhand knot at least 25 mm from the end of the rope to prevent slipping. • Thread the other end of the rope through the loop of the manual release cable. • Adjust...

Page 8 - SETTING THE LIMITS

Travel limits regulate the points at which the door willstop when moving UP or DOWN. During the set upprocedure, the motor will run and operate the door.The opener must be fully installed on the door and allinstallation steps completed before proceeding. PREPARATION:• Position the door about half wa...

Page 9 - • Door should be closed before proceeding.; • The door must travel through a complete cycle, up and; FIXING WARNING LABELS; STANDARD INSTALLATION COMPLETE; SETTING THE FORCE

The force, as measured on the closing edge of the door,should not exceed 400 N (40 kg). If the closing force ismeasured to more than 400 N, The Protector System TM (IR Beams) must be installed (refer section 16). The force setting regulates the amount of powerrequired to open and close the door. • D...

Page 10 - Installing and adjusting:; IR Beams must be installed; grey

NOTE: This accessory must be used for allinstallations where the closing force as measuredon the bottom of the door is over 400 N (40 kgf). After the opener has been installed and adjusted, theProtector System™ (IR Beams) accessory can beinstalled. Instructions are included with this accessory. The ...

Page 11 - DELETING ALL transmitter codes; • Press and hold the learn button until the; WIRELESS PROGRAMMING (OPTIONAL ACCESSORIES)

10 ADDING transmitters using the learn button• Press and hold down the transmitter button you wish to program to the opener. • The orange LED will flash continuously to indicate it is receiving signal from the transmitter. • Press and release the learn button on the opener.• The courtesy LED will fl...

Page 12 - Learn button programming

Wireless Keypad 8747AML Using the (purple) learn button: 1. Press and release the (purple) learn button (1) on the opener (the orange LED will light). 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on thekeypad (2), then press and hold the ENTER button. ...

Page 13 - Multifunction control panel; Model 8747AML Keyless entry system; ACCESSORIES; SPECIAL FEATURES; • Slide the transmitter onto bracket.

12 1 2 LOCK LIGHT 1.Multifunction control panel Connect white/red wire to the red “wired wallcontrol” quick connect terminal and the white wireto the white “wired wall control” quick connectterminal. 2.The Protector System™ (IR Beams) Connect both white wires to the white “safety beam”quick connect ...

Page 14 - TROUBLESHOOTING

TROUBLESHOOTING 1.The opener doesn't operate from either the GREEN start button or the transmitters: • Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box. • Have you disabled all door locks? Review installation instruction warnings on page 1. • ...

Page 15 - OPERATION OF YOUR OPENER; Opening the door manually:; MAINTENANCE OF YOUR OPENER; CARE OF YOUR OPENER

14 OPERATION OF YOUR OPENER Your opener can be activated by any of the followingdevices: • The GREEN start button Hold the button down until door starts to move. • The wall control, outside keyswitch or keyless entry system (if you have installed any of theseaccessories). • The transmitter or wirele...

15 © 2012 The Chamberlain Group, Inc 114B4542B TM Trademark of The Chamberlain Group, Inc. ® Registered Trademark of The Chamberlain Group, Inc. Chamberlain Limited Warranty, we may, subject to your other rights andremedies as a consumer, charge you a fee to repair, replace and/orreturn the Unit to ...

Chamberlain CR550 - Manual

Table of Contents:

Summary

Other Chamberlain Models