Chamberlain 1022 - Manual - manualsarea.com

Page 2 - NOTE; IMPORTANT SAFETY INSTRUCTIONS; SAFETY INFORMATION; POTENTIAL

PN# 3642036534, 02/26/2010 REV. 1 2 OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since movingobjects, springs under tension, and electric motors can cause injuries, your saf...

Page 3 - Operates door opener from inside garage.; SAFETY FEATURES; SECTION

PN# 3642036534, 02/26/2010 REV. 1 3 TABLE OF CONTENTS OPENER FEATURES INTELLICODE ® Rolling Code Security System. An electronic rolling code system that enhances the security ofthe door opener by continuously changing the access codeeach time the remote control is used. The door openerresponds to ea...

Page 4 - PRE-INSTALLATION CHECK LIST; This opener is designed for use with SECTIONAL doors only.; The door opener’s header bracket; you should consider; WA R N I N G; The outlet should be; WA R N I N G

PN# 3642036534, 02/26/2010 REV. 1 6 To avoid damage to your door and/or opener, make sure you disable and/or remove any door locks, ropes, and/or cables(NOT door lift cables) prior to installing youropener . ( Refer to Section 1.) 4 PRE-INSTALLATION CHECK LIST FOR HELP-1.800.354.3643 OR WWW.GENIECOM...

Page 5 - TYPICAL SECTIONAL DOOR INSTALLATION

PN# 3642036534, 02/26/2010 REV. 1 5 TYPICAL SECTIONAL DOOR INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM TYPICAL SUPPORT BRACKET (NOT PROVIDED) EXTENSION SPRING OR TORSION SPRING SAFE-T-BEAM ® BRACES ADDED HEADER BRACKETMOUNTING BOARD POWER CORD (APPROX. 45 IN.) TO 120V GROUNDED OUTLE...

Page 6 - Not Shown Full Size .

PN# 3642036534, 02/26/2010 REV. 1 6 RECOMMENDED TOOLS FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 3/16" Drill Bit 1/4", 7/16", 3/8" and 1/2" Sockets Step ladder Drill Ratchet Carpenter’s level Pencil Tape measure Wire strippers Phillips screwdriver Adjustable wrench PARTS IDE...

Page 7 - DO NOT RETURN TO POINT OF PURCHASE.

PN# 3642036534, 02/26/2010 REV. 1 FASTENERS - Shown Full size (See Parts List below for full description.) Lag screw - 5/16" x 2" Self-drilling Screw 1/4"-20 x 3/4" Hex Flange Nut 1/4"-20 Cotter pin Clevis pin 5/16" x 3/4" Hex Bolt - 5/16"-18 x 3/4" Hex Flange Nut...

Page 8 - CHAIN

PN# 3642036534, 02/26/2010 REV. 1 8 1-PIECE RAIL HARDWARE ASSEMBLED VIEW FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 3-PIECE RAIL HARDWARE ASSEMBLED VIEW Tensioner Rail with chain Chain Chain Connector Release Knob Header Bracket Power Head Power Cord Carriage Assembly Clevis Pin, Long & Cot...

Page 9 - PENER ASSEMBLY; There are 4 boxes inside the carton. Each box is; Remove the motor power head and place it on; until opener is fully assembled and; CAUTION; IMPORTANT INSTALLATION INSTRUCTIONS

PN# 3642036534, 02/26/2010 REV. 1 9 PENER ASSEMBLY FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 1 NOTE: Three (3) piece rail assemblies are for a 7foot high door. Clear a workspace area to unpack and organize boxand contents for assembly. 1. There are 4 boxes inside the carton. Each box is number...

Page 10 - Rail Assembly for CHAIN DRIVE OPENER; Chain and rail should extend; Rail Assembly for BELT DRIVE OPENER; After both rail; CHAIN DRIVE RAILS; Mount chain/belt to tensioner pulley; Wrap around tensioner pulley

10 FIG. 1-2 Split Rail sections . FIG. 1-3 Split Rail assembly . A B Chain Rail Center Rail End Rail Wire Tie(s) Rail Assembly for CHAIN DRIVE OPENER NOTE: For split rail clamps, nuts, and boltslocate Bag 0 from Box 1. 3. Remove the two rail sections that are not connected to the chain and place the...

Page 11 - POWER HEAD & RAIL ASSEMBLY; Assembly for CHAIN DRIVE OPENER; The chain adjustment nut is; Chain adjustment; Disable garage door lock; Belt adjustment; Assembly for BELT DRIVE OPENER; The belt adjustment nut is located in; C A U T I O N

POWER HEAD & RAIL ASSEMBLY Assembly for CHAIN DRIVE OPENER NOTE: Handle carefully! Drive chain can slide out of rail.NOTE: For power head and rail assembly locateBag 1 from Box 1.NOTE: Copy serial number from power headframe and record it on warranty page. NOTE: Standing at the powerhead, facing...

Page 12 - NSTALLATION; Finding header bracket mounting location; Do NOT move door spring!; WARNING

12 PN# 3642036534, 02/26/2010 REV. 1 FIG. 2-2 Finding highest point of travel . NSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 2 HEADER AND DOOR MOUNTING BRACKETS: 1. Finding header bracket mounting location . • Close garage door. – Use a pencil and level. a) Mark center of garage door ...

Page 13 - Position assembly and align; HEADER BRACKET; Mounting Straps; Mounting the power head; Attach angle iron to beams; FIG. 2-5 Rail mounting to header bracket

MOUNTING THE OPENER: 1. Getting started . • Position assembled rail on wall next to header bracket (Fig. 2-4) . – Place material on floor under power head to protect from scratching. (A box, stool, or similar device may be needed to clear a torsion spring.) NOTE: For header bracket pins locate Bag 2...

Page 14 - INSTALL DOOR ARMS; short clevis pin & cotter pin

14 PN# 3642036534, 02/26/2010 REV. 1 DOOR BRACKET: NOTE: For door bracket and bolts locate Bag 4from Box 2. 1. Finding door bracket mounting location . • Door bracket is mounted as high on door as possible along vertical centerline and NO LOWER THAN top set of rollers (Fig. 2-7) . 2. Mounting the do...

Page 15 - WALL CONSOLE INSTALLATION; Splitting and stripping; Black

PN# 3642036534, 02/26/2010 REV. 1 NOTE: For Wall Console, wire and insulated staples locate Bags 6 and 7 from Box 2. 1. Wall Console location. Wall Console location should be in direct sight of door. It should be at least five feet (5') above floor to prevent small children from operating door. ...

Page 16 - Do NOT install rear cover yet.; Insulated; wire guide; Mounting Entrapment warning label; Independent Light Control; Controls door opener lights from inside garage; Vacation Locking Switch; Open and closes door from

PN# 3642036534, 02/26/2010 REV. 1 16 3.Securely fasten wires. Securely fasten wires to ceiling and wall using insulated staples provided.– Use insulated staples.– Staples should be snug only. If rear cover is attached to power head, remove it. On power head:– Route wall console wires through w...

Page 17 - SYSTEM INSTALLATION; System is; Dashed Line = striped wire

PN# 3642036534, 02/26/2010 REV. 1 17 AFE-T-BEAM ® SYSTEM INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 4 NOTE: The opener will not close the door automatically unless the Safe-T-Beam ® System is installed. NOTE: For Safe-T-Beam®, screws, wire, and insulated staples locate items and Ba...

Page 18 - wire to power head wire; alignment check must be; Insert wires; Cover clips

PN# 3642036534, 02/26/2010 REV. 1 18 3b. Wiring (pre-wired) . Route wire from wall to Safe-T-Beam ® sensors (Fig. 4-5b) . Splice pre-wiring to shortened sensor wire, match wire pairs dash-to-dash and plain-to-plain . - Trim sensor wire to approximately one foot (1 ft) from sensor. - Split and st...

Page 19 - ONNECTING TO POWER; grounding; Check local building codes; alignment; INFRARED PROTECTION FUNCTION; before; ƁƁ; Remove motor cover; WITH PERMANENT WIRING:; Instructions for Electrician.; Motor Cover Screws

PN# 3642036534, 02/26/2010 REV. 1 19 ONNECTING TO POWER FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 5 Plug the opener into a properly grounded electrical outlet (Fig. 5-1). To reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third ( grounding ) pin. ...

Page 20 - OOR LIMITS; Limit controls; Engage Chain/Belt Connector to Carriage; Set Close Travel Limit

PN# 3642036534, 02/26/2010 REV. 1 20 OOR LIMITS FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 6 The OPEN (UP) and CLOSE (DOWN) door positionsare controlled by making the adjustments on thepanel located on the bottom of the power head. Theadjustments that can be made are: • Close Travel Limit, • Op...

Page 21 - Emergency release cable to carriage; DOOR; Engage/Disengage Carriage Lock; CARRIAGE LOCK; opener power head; Keyed Emergency Release Operation Instructions

21 Obtain standard emergency release kit and remove S-hook from the cable end that attaches to the opener carriage. 1. Attach the emergency release cable loop end to the opener carriage as shown (FIG 6-4). Properly connecting the release cable to the carriage fitting will enable the correct carriage...

Page 22 - x 4 under center of door opening.; CONTACT REVERSE TEST; clockwise; OPEN; Force Control Adjustment

PN# 3642036534, 02/26/2010 REV. 1 22 FIG. 6-6 2 x 4 under center of door opening. CONTACT REVERSE TEST The force adjustments and limit switch settingsMUST BE COMPLETED before testing. 1. Testing . Open garage door using wall button.– Place a 2" x 4" board (laid flat) under center of garage...

Page 23 - FCC and IC CERTIFIED; Learn code button and LED; ROGRAMMING REMOTE CONTROLS; LOST OR STOLEN REMOTE; Your door opener will no

PN# 3642036534, 02/26/2010 REV. 1 23 FCC and IC CERTIFIED FIG. 7-1 Learn code button and LED SET SET OPEN FORCE CLOSE CODE LEARN LIMIT MANUAL Open Travel Limit Open Set Limit Button Close Travel Limit Close Set Limit Button Down Force Control Adjustment Up Force Control Adjustment Learn Code Button ...

Page 24 - EMOTE CONTROL; BATTERY REPLACEMENT AND VISOR CLIP INSTALLATION; Battery replacement; Alkaline; LIGHT BULB / LENS INSTALLATION; heavy duty service

EMOTE CONTROL BATTERY REPLACEMENT AND VISOR CLIP INSTALLATION 8 FIG. 8-1 Open battery cover . 1. Battery replacement . • To open gently push straight out on battery cover lock tab as shown (Fig. 8-1) . • Flip open battery cover. – Remove old battery. • Make sure new battery is facing proper directio...

Page 25 - If you have any questions, please do not hesitate to contact Genie; IMPORTANT SAFETY INSTRUCTIONS; SAVE THESE INSTRUCTIONS.; To reduce the risk of severe injury or death:; MAINTENANCE

PN# 3642036534, 02/26/2010 REV. 1 25 Use wall button supplied with opener. Any other wall control can causethe opener to operate unexpectedly. WARNING If you have any questions, please do not hesitate to contact Genie ® customer service at: 1.800.354.3643 IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FO...

Page 26 - CIRCUIT WIRING DIAGRAM; POWER CORD; CORDON DE SECTEUR; PRIMARY; SECONDARY; L’ouverture du couvercle peut entraîner des chocs électriques.; CHOQUE ELÉCTRICO

PN# 3642036534, 02/26/2010 REV. 1 26 CIRCUIT WIRING DIAGRAM FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 1 2 3 4 5 6 1 2 3 4 1 2 3 1 2 POWER CORD CORDON DE SECTEUR CABLE ELÉCTRICO TERMINAL BLOCK BORNE BLOQUE DE TERMINALES WHITE BLANC BLANCO BLACK NOIR NEGRO GREEN VERT VERDE SURGE PROTECTOR (MOV) ...

Page 27 - TROUBLESHOOTING GUIDE -; OPERATION; PROBLEM; OR

PN# 3642036534, 02/26/2010 REV. 1 27 TROUBLESHOOTING GUIDE - OPERATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM PROBLEM WHAT TO DO Opener does NOT runfrom Wall Console. Check power source.– Plug a lamp into outlet used for power head. If lamp works, power source is OK.– If not, check fuse o...

Page 28 - POWER HEAD LED; Power head LED; Possible Problem; Red LED

PN# 3642036534, 02/26/2010 REV. 1 TROUBLESHOOTING GUIDE - POWER HEAD LED FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Power head LED Possible Problem Solution Red LED showing Green LED showing OFF OFF Normal operation None required Continuous ON Programming incomplete Complete programming 1 B...

Page 29 - TRANSMITTER COMPLIANCE STATEMENT

PN# 3642036534, 02/26/2010 REV. 1 29 Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture. No warranty is madethat they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another country, the importermus...

Page 30 - Limited Warranty

GMI Holdings, Inc d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified opener Model 1022 or opener Model 1024 or opener Model 1042 (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free...

Chamberlain 1022 - Manual

Table of Contents:

Summary

Other Chamberlain Models